[PATCH 18/19] arm64: kdump: update a kernel doc

AKASHI Takahiro takahiro.akashi at linaro.org
Mon Jan 18 21:35:44 PST 2016


On 01/19/2016 10:43 AM, Dave Young wrote:
> On 01/18/16 at 07:26pm, AKASHI Takahiro wrote:
>> On 01/16/2016 05:16 AM, Mark Rutland wrote:
>>> On Fri, Jan 15, 2016 at 07:18:38PM +0000, Geoff Levand wrote:
>>>> From: AKASHI Takahiro <takahiro.akashi at linaro.org>
>>>>
>>>> This patch adds arch specific descriptions about kdump usage on arm64
>>>> to kdump.txt.
>>>>
>>>> Signed-off-by: AKASHI Takahiro <takahiro.akashi at linaro.org>
>>>> ---
>>>>   Documentation/kdump/kdump.txt | 23 ++++++++++++++++++++++-
>>>>   1 file changed, 22 insertions(+), 1 deletion(-)
>>>>
>>>> diff --git a/Documentation/kdump/kdump.txt b/Documentation/kdump/kdump.txt
>>>> index bc4bd5a..36cf978 100644
>>>> --- a/Documentation/kdump/kdump.txt
>>>> +++ b/Documentation/kdump/kdump.txt
>>>> @@ -18,7 +18,7 @@ memory image to a dump file on the local disk, or across the network to
>>>>   a remote system.
>>>>
>>>>   Kdump and kexec are currently supported on the x86, x86_64, ppc64, ia64,
>>>> -s390x and arm architectures.
>>>> +s390x, arm and arm64 architectures.
>>>>
>>>>   When the system kernel boots, it reserves a small section of memory for
>>>>   the dump-capture kernel. This ensures that ongoing Direct Memory Access
>>>> @@ -249,6 +249,20 @@ Dump-capture kernel config options (Arch Dependent, arm)
>>>>
>>>>       AUTO_ZRELADDR=y
>>>>
>>>> +Dump-capture kernel config options (Arch Dependent, arm64)
>>>> +----------------------------------------------------------
>>>> +
>>>> +1) The maximum memory size on the dump-capture kernel must be limited by
>>>> +   specifying:
>>>> +
>>>> +   mem=X[MG]
>>>> +
>>>> +   where X should be less than or equal to the size in "crashkernel="
>>>> +   boot parameter. Kexec-tools will automatically add this.
>>>
>>>
>>> This is extremely fragile, and will trivially fail when the kernel can
>>> be loaded anywhere (see [1]).
>>
>> As I said before, this restriction also exists on arm, but I understand
>> that recent Ard's patches break it.
>>
>>> We must explicitly describe the set of regions the crash kernel may use
>>> (i.e. we need base and size). NAK in the absence of that.
>>
>> There seem to exist several approaches:
>> (a) use a device-tree property, "linux,usable-memory", in addition to "reg"
>>      under "memory" node
>> (b) use a kernel's early parameter, "memmap=nn[@#$]ss"
>>
>> Power PC takes (a), while this does not work on efi-started kernel
>> because dtb has no "memory" nodes under efi.
>> X86 takes (b). If we take this, we will need to overwrite a weak
>> early_init_dt_add_memory().
>
> X86 takes another way in latest kexec-tools and kexec_file_load, that is
> recreating E820 table and pass it to kexec/kdump kernel, if the entries
> are over E820 limitation then turn to use setup_data list for remain
> entries.

Thanks. I will visit x86 code again.

> I think it is X86 specific. Personally I think device tree property is
> better.

Do you think so?

-Takahiro AKASHI


>
> Thanks
> Dave
>



More information about the kexec mailing list