[Help Test] kdump, x86, acpi: Reproduce CPU0 SMI corruption issue after unsetting BSP flag

[HATAYAMA Daisuke]

Hello,

I've addressing kdump restriction that there's only one cpu available
on the kdump 2nd kernel. Now I need to check if the following CPU0 SMI
corruption issue fixed in the following commit can again be reproduced
by unsetting BSP flag of the boot cpu:

commit 74b5820808215f65b70b05a099d6d3c969b82689
Author: Bjorn Helgaas <bjorn.helgaas at hp.com>
Date:   Wed Jul 29 15:54:25 2009 -0600

    ACPI: bind workqueues to CPU 0 to avoid SMI corruption

    On some machines, a software-initiated SMI causes corruption unless the
    SMI runs on CPU 0.  An SMI can be initiated by any AML, but typically it's
    done in GPE-related methods that are run via workqueues, so we can avoid
    the known corruption cases by binding the workqueues to CPU 0.

    References:
        http://bugzilla.kernel.org/show_bug.cgi?id=13751
        https://bugs.launchpad.net/bugs/157171
        https://bugs.launchpad.net/bugs/157691

    Signed-off-by: Bjorn Helgaas <bjorn.helgaas at hp.com>
    Signed-off-by: Len Brown <len.brown at intel.com>

The reason is that in the current situation, I have two ideas to deal
with the avove kdump restriction:

  1) Disable BSP at the 2nd kernel, posted at:
    [PATCH v1 0/2] x86, apic: Disable BSP if boot cpu is AP
    https://lkml.org/lkml/2012/10/16/15

  2) Unset BSP flag at the 1st kernel, suggested by Eric Biederman
     during the discussion of the idea 1).

On the idea 1), BSP is disabled on the kdump 2nd kernel. My conclusion
is that we have no method to reset BSP, i.e. recover BPS's healthy
state, while we can recover AP by means of INIT as described in MP
specification.

The idea 2) is simpler. We unset BSP flag of the boot cpu at 1st
kernel. The behaviour when receiving INIT depends on whether or not
BSP flag is set or not on its MSR; we can set and unset BSP flag of
MSR freely at runtime. (I don't mean we should).

So, next thing I should do is to evalute risk of the idea 2). In fact,
during the discussion of the idea 1), HPA pointed out that some kind
of firmware affects if BSP flag is unset. Also, maybe from the same
reason, recently introduced cpu0 hot-plugging feature by Fenghua Yu
doesn't appear to unset BSP flag.

The biggest problem next is that I don't have any machines reported in
the bugzilla articles; this issue inherently depends on firmware.

So, could anyone help testing the idea 2) above if you have which of
the following machines? (or other ones that can lead to the same bug)

- HP Compaq 6910p
- HP Compaq 6710b
- HP Compaq 6710s
- HP Compaq 6510b
- HP Compaq 2510p

I prepared a small programs for this test. See the attached file.
The steps to try to reproduce the bug is as follows:

  1. $ tar xf bsp_flag_modules.tar.gz; cd bsp_flag_modules
  2. $ make # to build these programs
  3. $ insmod unsetbspflag.ko # to unset BSP flag of the boot cpu
  4. $ insmod getcpuinfo.ko # to confirm if BSP flag of the boot cpu has
                            # been unset.
     $ dmesg | tail
  5. Close the lid of the machine.
  6. Wait some minutes if necessary.
  7. Open the lid and you can see oops on the screen if bug has
    successfully been reproduced.

-- 
Thanks.
HATAYAMA, Daisuke
-------------- next part --------------
A non-text attachment was scrubbed...
Name: bsp_flag_modules.tar.gz
Type: application/gzip
Size: 9181 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/kexec/attachments/20130806/b72bc04b/attachment-0001.gz>