[Crash-utility] "cannot access vmalloc'd module memory" when loading kdump'ed vmcore in crash
Worth, Kevin
kevin.worth at hp.com
Sat Oct 4 13:34:30 EDT 2008
Hi Dave (and kexec list),
Including kexec list in this email because Dave mentioned: "Show the outputs of the live system and the subsequent dumpfile. If they both end up resolving to the same physical address, then there's an issue with the dumpfile." Things appear to be resolving to the same address (though I suspect Dave can confirm).
Please see below. I did have to censor one of the lines a bit- I do have a proprietary kernel module that I'm not able to discuss much about other than that it involves network traffic and should be causing any funky behavior here (the ext3 module seems to behave the same way). I just changed its name to "custom_lkm".
One additional note, although my "running system" kernel has the modified 3G kernel / 1G user split, my "capture kernel" is just the standard Ubuntu kernel (with 1G kernel / 3G user). The system panic'ed immediately if I tried to use my modified kernel as the "capture kernel". I figured this was outside the norm so I've been using the standard kernel to perform the capture.
First I ran through some commands Dave suggested on the live system (my contexts for the live system and dump were different, but what might be more important is that "vm -p" on a live system produced errors, while on the dump it did not):
crash> vm
PID: 32227 TASK: 47bc8030 CPU: 0 COMMAND: "crash"
MM PGD RSS TOTAL_VM
f7e67040 5fddfe00 63336k 67412k
VMA START END FLAGS FILE
f3ed61d4 8048000 83e5000 1875 /root/crash
f3ed6d84 83e5000 83fc000 101877 /root/crash
....
crash> vm -p
PID: 32227 TASK: 47bc8030 CPU: 0 COMMAND: "crash"
MM PGD RSS TOTAL_VM
f7e67040 5fddfe00 63336k 67412k
VMA START END FLAGS FILE
f3ed61d4 8048000 83e5000 1875 /root/crash
VIRTUAL PHYSICAL
vm: read error: physical address: 10b60b000 type: "page table"
crash> p modules
modules = $2 = {
next = 0xf9088284,
prev = 0xf8842104
}
crash> module 0xf9088280
struct module {
state = MODULE_STATE_LIVE,
list = {
next = 0xf8ff9d84,
prev = 0x403c63a4
},
name = "custom_lkm\000\000\000\000\000\000\000\000\000\000\000\000\000\000\00
0\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\00
0\000\000\000\000\000\000\000\000\000\000\000\000\000",
mkobj = {
kobj = {
k_name = 0xf90882cc "custom_lkm",
name = "custom_lkm\000\000\000\000\000\000\000\000",
kref = {
refcount = {
counter = 3
}
},
entry = {
next = 0x403c6068,
prev = 0xf8ff9de4
},
...
crash> vtop 0xf9088280
VIRTUAL PHYSICAL
f9088280 119b98280
PAGE DIRECTORY: 4044b000
PGD: 4044b018 => 6001
PMD: 6e40 => 1d515067
PTE: 1d515440 => 119b98163
PAGE: 119b98000
PTE PHYSICAL FLAGS
119b98163 119b98000 (PRESENT|RW|ACCESSED|DIRTY|GLOBAL)
crash> mod | grep ext3
f88c8000 ext3 132616 (not loaded) [CONFIG_KALLSYMS]
crash> module 0xf88c8000
struct module {
state = MODULE_STATE_LIVE,
list = {
next = 0xf88a6604,
prev = 0xf885d584
},
name = "ext3\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\0
00\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\0
00\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000",
mkobj = {
kobj = {
k_name = 0xf88c804c "ext3",
name = "ext3\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000",
kref = {
refcount = {
counter = 3
}
},
entry = {
next = 0xf885d5e4,
prev = 0xf88a6664
},
...
(Realized afterward that I forgot to vtop ext3. Let me know if it's needed and I can repeat this procedure)
>From dump file:
crash> vm
PID: 4323 TASK: 47be0a90 CPU: 0 COMMAND: "bash"
MM PGD RSS TOTAL_VM
5d683580 5d500dc0 2616k 3968k
VMA START END FLAGS FILE
5fc2aac4 8048000 80ee000 1875 /bin/bash
5fe5f0cc 80ee000 80f3000 101877 /bin/bash
...
crash> vm -p
PID: 4323 TASK: 47be0a90 CPU: 0 COMMAND: "bash"
MM PGD RSS TOTAL_VM
5d683580 5d500dc0 2616k 3968k
VMA START END FLAGS FILE
5fc2aac4 8048000 80ee000 1875 /bin/bash
VIRTUAL PHYSICAL
8048000 FILE: /bin/bash OFFSET: 0
8049000 FILE: /bin/bash OFFSET: 1000
804a000 FILE: /bin/bash OFFSET: 2000
...no errors, lots of output
crash> modules
modules = $2 = {
next = 0xf9088284,
prev = 0xf8842104
}
crash> module 0xf9088280
struct module {
state = MODULE_STATE_LIVE,
list = {
next = 0x0,
prev = 0x0
},
name = "\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\0
00\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\0
00\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\0
00\000",
mkobj = {
kobj = {
k_name = 0x0,
name = "\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\0
00\000\000",
kref = {
refcount = {
counter = 0
}
},
entry = {
next = 0x0,
prev = 0x0
...
crash> vtop 0xf9088280
VIRTUAL PHYSICAL
f9088280 119b98280
PAGE DIRECTORY: 4044b000
PGD: 4044b018 => 6001
PMD: 6e40 => 1d515067
PTE: 1d515440 => 119b98163
PAGE: 119b98000
PTE PHYSICAL FLAGS
119b98163 119b98000 (PRESENT|RW|ACCESSED|DIRTY|GLOBAL)
PAGE PHYSICAL MAPPING INDEX CNT FLAGS
47337300 119b98000 0 0 1 80000000
crash> mod | grep ext3
mod: cannot access vmalloc'd module memory
(using the same address that ext3 had in a running system)
crash> module 0xf88c8000
struct module {
state = MODULE_STATE_LIVE,
list = {
next = 0x0,
prev = 0x0
},
name = "\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\0
00\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\0
00\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\0
00\000",
mkobj = {
kobj = {
k_name = 0x0,
name = "\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\0
00\000\000",
kref = {
refcount = {
counter = 0
}
},
entry = {
next = 0x0,
prev = 0x0
...
crash> vtop 0xf88c8000
VIRTUAL PHYSICAL
f88c8000 13905f000
PAGE DIRECTORY: 4044b000
PGD: 4044b018 => 6001
PMD: 6e20 => 1d5fc067
PTE: 1d5fc640 => 13905f163
PAGE: 13905f000
PTE PHYSICAL FLAGS
13905f163 13905f000 (PRESENT|RW|ACCESSED|DIRTY|GLOBAL)
PAGE PHYSICAL MAPPING INDEX CNT FLAGS
Thanks again for your continued assistance. I hope this is helpful information.
-Kevin
-----Original Message-----
From: crash-utility-bounces at redhat.com [mailto:crash-utility-bounces at redhat.com] On Behalf Of Dave Anderson
Sent: Friday, October 03, 2008 8:44 AM
To: Discussion list for crash utility usage, maintenance and development; kexec at lists.infradead.org
Subject: Re: [Crash-utility] "cannot access vmalloc'd module memory" when loading kdump'ed vmcore in crash
NOTE: I've restored the kexec list to this discussion because
this 1G/3G issue does have ramifications w/respect to kexec-tools.
I'm first going to ramble on about crash utility debugging for a
bit here, but for the kexec/kdump masters in the audience, please
at least take a look at the end of this message (do a "find in this
message" for "KEXEC-KDUMP") where I discuss the kexec-tools
hardwiring of the x86 PAGE_OFFSET to c000000, and whether it
could screw up the dumpfile contents for Kevin's 1G/3G split
where his PAGE_OFFSET is 40000000.
First, the crash discussion...
Worth, Kevin wrote:
> Yep, I can run mod commands on a live system just fine.
>
> Looks like "next" doesn't point to fffffffc...
>
No, but it's 0x0, and therefore the "next" module in the
list gets calculated as 0 - offset-of-list-member, or
fffffffc. And "MODULE_STATE_LIVE" is being shown by dumb
luck because its enumerator value is 0:
> crash> module f9088280
> struct module {
> state = MODULE_STATE_LIVE,
> list = {
> next = 0x0,
> prev = 0x0
> },
> name = "\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\0
> 00\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\0
> 00\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\0
> 00\000",
> mkobj = {
> kobj = {
> k_name = 0x0,
> name = "\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\000\0
> 00\000\000",
> kref = {
> refcount = {
> counter = 0
...
>
> ...and all the rest of the struct is zeros too...
Right, so we know bogus data is being read from the dumpfile. The question is:
(1) whether the virtual-to-physical address translation is
failing somehow, or
(2) the dumpfile is screwed up.
> Does the following mean that user virtual address translations are failing too?
>
> crash> set
> PID: 4304
> COMMAND: "bash"
> TASK: 5d7e9030 [THREAD_INFO: f4b70000]
> CPU: 0
> STATE: TASK_RUNNING (SYSRQ)
> crash> vm
> PID: 4304 TASK: 5d7e9030 CPU: 0 COMMAND: "bash"
> MM PGD RSS TOTAL_VM
> f7e7f040 5d5002c0 2616k 3972k
> VMA START END FLAGS FILE
> 5fe454ec 8048000 80ee000 1875 /bin/bash
> 5fe45e34 80ee000 80f3000 101877 /bin/bash
> ...
>
> crash> rd 8048000
> rd: invalid kernel virtual address: 8048000 type: "32-bit KVADDR"
> crash> rd -u 8048000
> rd: invalid user virtual address: 8048000 type: "32-bit UVADDR"
> crash> rd 80ee000
> rd: invalid kernel virtual address: 80ee000 type: "32-bit KVADDR"
> crash> rd -u 80ee000
> rd: invalid user virtual address: 80ee000 type: "32-bit UVADDR"
>
The fact that crash initially presumes that 8048000 and 80ee000 are
kernel virtual addresses can be explained by this part of "help -v"
debug output:
flags: 515a
(NODES_ONLINE|ZONES|PERCPU_KMALLOC_V2|COMMON_VADDR|KMEM_CACHE_INIT|FLATMEM|PERCPU_KMALLOC_V2_NODES)
The "COMMON_VADDR" flag should *only* be set in the case of
the Red Hat hugemem 4G/4G split kernel. However, I believe that
crash should be able to continue even if the bit is set, as is
the case when you run live. It is a crash issue having to
do with your 4000000 PAGE_OFFSET, but I think it's benign,
especially if user virtual address accesses run OK on your
live system.
That's one thing that needs verification. The "invalid user
virtual address" messages above that you get *even* when you
use "-u" would typically be generated as a result of the user
virtual-to-physical address translation. However, they also
could be generated if the virtual page being accessed has been
swapped out.
A better test would be translate all virtual address in the
user address space in one fell swoop with "vm -p". It's
a verbose command, but for each user virtual page in the
current context, it will translate it to:
(1) the current physical address location, or
(2) if it's not in memory, but is backed by a file, it will show
what file it comes from, or
(3) if it's been swapped out, what swapfile location is has been
swapped out to, or
(4) if it's an anonymous page (with no file backing) that hasn't
been touched yet, it will show "(not mapped)"
Here's a truncated example:
PID: 19839 TASK: f7b03000 CPU: 1 COMMAND: "bash"
MM PGD RSS TOTAL_VM
f6dc5740 f745c9c0 1392k 4532k
VMA START END FLAGS FILE
f69019bc 6fa000 703000 75 /lib/libnss_files-2.5.so
VIRTUAL PHYSICAL
6fa000 12fdba000
6fb000 12fdbb000
6fc000 FILE: /lib/libnss_files-2.5.so OFFSET: 2000
6fd000 FILE: /lib/libnss_files-2.5.so OFFSET: 3000
6fe000 12f660000
6ff000 12f2cf000
700000 FILE: /lib/libnss_files-2.5.so OFFSET: 6000
701000 FILE: /lib/libnss_files-2.5.so OFFSET: 7000
702000 12fc6f000
VMA START END FLAGS FILE
f69013e4 703000 704000 100071 /lib/libnss_files-2.5.so
VIRTUAL PHYSICAL
703000 54791000
VMA START END FLAGS FILE
f6901d84 704000 705000 100073 /lib/libnss_files-2.5.so
VIRTUAL PHYSICAL
704000 12450d000
VMA START END FLAGS FILE
f6901284 a7c000 a96000 875 /lib/ld-2.5.so
VIRTUAL PHYSICAL
a7c000 6ea28000
a7d000 101f62000
a7e000 6e6f3000
a7f000 6e07e000
a80000 6e084000
a81000 114c8e000
...
Run the command above on a "bash" context on *both* the live
system and the dumpfile -- they should behave in a similar manner,
but I'm guessing you may get some bizarre errors when you
run it on the dumpfile.
Getting back to the base problem with the bogus module read,
here'a suggestion for debugging this. It requires that you
run the live system, gather some basic data with the crash
utility, and then enter "alt-sysrq-c". What we want to see
is a virtual-to-physical translation of the first module in
the module list on the live system. Then crash the system.
Then we want to do the same thing on the subsequent vmcore
to see if the same physical address references are made during
the translation.
So for example, on my live system, the "/dev/crash" kernel
module is the last module entered, and therefore is pointed
to by the base kernel's "modules" list_head:
crash> p modules
modules = $2 = {
next = 0xf8bd0904,
prev = 0xf882b104
}
Subtract 4 from the "next" pointer, and display the module:
crash> module 0xf8bd0900
struct module {
state = MODULE_STATE_LIVE,
list = {
next = 0xf8caf984,
prev = 0xc06787b0
},
name = "crash",
mkobj = {
kobj = {
k_name = 0xf8bd094c "crash",
name = "crash",
kref = {
refcount = {
counter = 2
}
},
...
Then translate it:
crash> vtop 0xf8bd0900
VIRTUAL PHYSICAL
f8bd0900 48ba1900
PAGE DIRECTORY: c0724000
PGD: c0724018 => 4001
PMD: 4e28 => 37ae067
PTE: 37aee80 => 48ba1163
PAGE: 48ba1000
PTE PHYSICAL FLAGS
48ba1163 48ba1000 (PRESENT|RW|ACCESSED|DIRTY|GLOBAL)
PAGE PHYSICAL MAPPING INDEX CNT FLAGS
c1917420 48ba1000 0 785045 1 c0000000
crash>
Do the same type of thing on your live system (where you'll
have a different module), and save the output in a file.
Then immediately enter "alt-sysrq-c".
With the resultant dumpfile, perform the same "p modules",
"module <next-address-4>", and "vtop <next-address-4> steps
as done above. The output *should* be identical, although
we're primarily interested in the vtop output given that
the "module <next-address-4>" will probably show garbage.
(BTW, this presumes that the first module in the kernel list
will still return bogus data like your current dumpfile. That
may not be the case, and if so, we'll need to do something
similar but different. For example, on the live system, capture
the address of the "ext3" module, vtop it, crash the system,
and then do the same thing in the dumpfile. You might want to
do that anyway, just in case the default behavior is different.
Then again, maybe it will work both live and in the dumpfile
for the ext3 module address, in which case we'll need to go in a
different debug-direction...)
Show the outputs of the live system and the subsequent dumpfile.
If they both end up resolving to the same physical address,
then there's an issue with the dumpfile.
KEXEC-KDUMP:
I talked to Vivek Goyal, who originally wrote the kexec-tools
facility, and he pointed me to this in the kexec-tools package's
"kexec/arch/i386/crashdump-x86.h" file:
#define PAGE_OFFSET 0xc0000000
#define __pa(x) ((unsigned long)(x)-PAGE_OFFSET)
#define __VMALLOC_RESERVE (128 << 20)
#define MAXMEM (-PAGE_OFFSET-__VMALLOC_RESERVE)
where for x86, it hard-wires the x86 PAGE_OFFSET to c0000000,
and will certainly result in a bogus MAXMEM given that your
PAGE_OFFSET is 40000000. I don't know if that is related to
the problem, but if you do a "readelf -a" of your vmcore file,
you'll see some funky virtual address values for each PT_LOAD
segment. They were dumped in the crash.log you sent me. Note
that the virtual address regions (p_vaddr) are c0000000,
c0100000, c5000000, ffffffffffffffff and ffffffffffffffff,
all of which are incorrect or nonsensical w/respect to your
1G/3G split:
Elf64_Phdr:
p_type: 1 (PT_LOAD)
p_offset: 728 (2d8)
p_vaddr: c0000000
p_paddr: 0
p_filesz: 655360 (a0000)
p_memsz: 655360 (a0000)
p_flags: 7 (PF_X|PF_W|PF_R)
p_align: 0
Elf64_Phdr:
p_type: 1 (PT_LOAD)
p_offset: 656088 (a02d8)
p_vaddr: c0100000
p_paddr: 100000
p_filesz: 15728640 (f00000)
p_memsz: 15728640 (f00000)
p_flags: 7 (PF_X|PF_W|PF_R)
p_align: 0
Elf64_Phdr:
p_type: 1 (PT_LOAD)
p_offset: 16384728 (fa02d8)
p_vaddr: c5000000
p_paddr: 5000000
p_filesz: 855638016 (33000000)
p_memsz: 855638016 (33000000)
p_flags: 7 (PF_X|PF_W|PF_R)
p_align: 0
Elf64_Phdr:
p_type: 1 (PT_LOAD)
p_offset: 872022744 (33fa02d8)
p_vaddr: ffffffffffffffff
p_paddr: 38000000
p_filesz: 2272854016 (87790000)
p_memsz: 2272854016 (87790000)
p_flags: 7 (PF_X|PF_W|PF_R)
p_align: 0
Elf64_Phdr:
p_type: 1 (PT_LOAD)
p_offset: 3144876760 (bb7302d8)
p_vaddr: ffffffffffffffff
p_paddr: 100000000
p_filesz: 1073741824 (40000000)
p_memsz: 1073741824 (40000000)
p_flags: 7 (PF_X|PF_W|PF_R)
p_align: 0
Now, the crash utility only uses the p_paddr physical address
fields for x86 dumpfiles, so that shouldn't be a problem.
But I wonder whether when the /proc/vmcore is put together
that there isn't some problem with the data that it accesses?
Thanks,
Dave
--
Crash-utility mailing list
Crash-utility at redhat.com
https://www.redhat.com/mailman/listinfo/crash-utility
More information about the kexec
mailing list