Configuring WiFi6 in hostapd

Tue Sep 8 14:57:34 EDT 2020

I have captured connection between a WiFi6 AP and a WiFi6 STA in wireshark.
I have attached a wireshark pcap file.
I could see HE capabilities exchange in Association request and response.
The iw phy output is below. I couldn't see HE connection in this output.

$iw dev wlp3s0 link
Connected to 8c:c6:81:69:86:65 (on wlp3s0)
    SSID: WiFi_AX200
    freq: 2437
    RX: 27838 bytes (199 packets)
    TX: 13319 bytes (97 packets)
    signal: -34 dBm
    rx bitrate: 26.0 MBit/s MCS 3
    tx bitrate: 2.0 MBit/s

    bss flags:    short-slot-time
    dtim period:    2
    beacon int:    100

On Wed, Sep 2, 2020 at 3:39 PM Krishna Chaitanya
<chaitanya.mgit at gmail.com> wrote:
>
> On Wed, Sep 2, 2020 at 6:38 PM Sugandh Huthanahally Mohan
> <sugandhgowda at gmail.com> wrote:
> >
> > On Wed, Sep 2, 2020 at 3:16 PM Sugandh Huthanahally Mohan
> > <sugandhgowda at gmail.com> wrote:
> > >
> > > On Tue, Sep 1, 2020 at 10:09 PM Krishna Chaitanya
> > > <chaitanya.mgit at gmail.com> wrote:
> > > >
> > > >
> > > > Well, not necessarily, but hostap side it looks fine, so,
> > > > we need to see why the STA isn't responding well, probably a
> > > > different draft implementation. At the very least we should start
> > > > with a sniffer capture of the association b/w the stations to check
> > > > the IEs.
> > >
> > > I am using wpa_supplicant in STA to connect  to AP.
> > > I am attaching hostapd logs and wpa_supplicant logs.
> > > I am observing that the STA is connecting and disconnecting when
> > > I try to connect STA to AP.
> > I guess this is a new STA with wpa_supplicant, right? Is it also AX200 based
> > chipset? In the STA mode, the kernel adds the HE IEs (either mac80211
> > or the driver),
> > so, but interestingly in your previous dmesg, I don't see any mac80211 logs.
> >
> > So, need dmesg logs that capture the connection (look for mac80211 logs).
> > >
> > > On Tue, Sep 1, 2020 at 10:09 PM Krishna Chaitanya
> > > <chaitanya.mgit at gmail.com> wrote:
> > > >
> > > > On Wed, Sep 2, 2020 at 1:23 AM Sugandh Huthanahally Mohan
> > > > <sugandhgowda at gmail.com> wrote:
> > > > >
> > > > > Hi Krishna,
> > > > >
> > > > > Currently I am not running wpa_supplicant.
> > > > > Is it necessary for hostapd?
> > > >
> > > > Well, not necessarily, but hostap side it looks fine, so,
> > > > we need to see why the STA isn't responding well, probably a
> > > > different draft implementation. At the very least we should start
> > > > with a sniffer capture of the association b/w the stations to check
> > > > the IEs.
> >
> > Yes this is a new STA connecting AP with wpa_supplicant.
> > It is also an AX200.
> > I don’t see mac80211 logs on the STA dmesg.
> > I am attaching dmesg of the station.
>
> These are from mac80211:
> [  152.255545] wlp3s0: authenticate with 8c:c6:81:69:86:65
> [  152.258347] wlp3s0: send auth to 8c:c6:81:69:86:65 (try 1/3)
> [  152.283971] wlp3s0: authenticated
> [  152.286624] wlp3s0: associate with 8c:c6:81:69:86:65 (try 1/3)
> [  152.293456] wlp3s0: RX AssocResp from 8c:c6:81:69:86:65
> (capab=0x411 status=0 aid=1)
> [  152.299672] wlp3s0: associated
> [  152.364843] IPv6: ADDRCONF(NETDEV_CHANGE): wlp3s0: link becomes ready
>
> I was hoping to see some prints disabling HE, but looks fine. So,
> still, nothing from the logs
> to say why HE is disabled in the STA (why it isn't sending HE IEs in
> assoc resp).
>
> Only Sniffer should tell us without resorting to Whitebox debug.
> >
> > On Wed, Sep 2, 2020 at 1:26 PM Krishna Chaitanya
> > <chaitanya.mgit at gmail.com> wrote:
> > >
> > > On Wed, Sep 2, 2020 at 3:16 PM Sugandh Huthanahally Mohan
> > > <sugandhgowda at gmail.com> wrote:
> > > >
> > > > On Tue, Sep 1, 2020 at 10:09 PM Krishna Chaitanya
> > > > <chaitanya.mgit at gmail.com> wrote:
> > > > >
> > > > >
> > > > > Well, not necessarily, but hostap side it looks fine, so,
> > > > > we need to see why the STA isn't responding well, probably a
> > > > > different draft implementation. At the very least we should start
> > > > > with a sniffer capture of the association b/w the stations to check
> > > > > the IEs.
> > > >
> > > > I am using wpa_supplicant in STA to connect  to AP.
> > > > I am attaching hostapd logs and wpa_supplicant logs.
> > > > I am observing that the STA is connecting and disconnecting when
> > > > I try to connect STA to AP.
> > > I guess this is a new STA with wpa_supplicant, right? Is it also AX200 based
> > > chipset? In the STA mode, the kernel adds the HE IEs (either mac80211
> > > or the driver),
> > > so, but interestingly in your previous dmesg, I don't see any mac80211 logs.
> > >
> > > So, need dmesg logs that capture the connection (look for mac80211 logs).
> > > >
> > > > On Tue, Sep 1, 2020 at 10:09 PM Krishna Chaitanya
> > > > <chaitanya.mgit at gmail.com> wrote:
> > > > >
> > > > > On Wed, Sep 2, 2020 at 1:23 AM Sugandh Huthanahally Mohan
> > > > > <sugandhgowda at gmail.com> wrote:
> > > > > >
> > > > > > Hi Krishna,
> > > > > >
> > > > > > Currently I am not running wpa_supplicant.
> > > > > > Is it necessary for hostapd?
> > > > >
> > > > > Well, not necessarily, but hostap side it looks fine, so,
> > > > > we need to see why the STA isn't responding well, probably a
> > > > > different draft implementation. At the very least we should start
> > > > > with a sniffer capture of the association b/w the stations to check
> > > > > the IEs.
> > >
> > >
> > >
> > > --
> > > Thanks,
> > > Regards,
> > > Chaitanya T K.
>
>
>
> --
> Thanks,
> Regards,
> Chaitanya T K.
-------------- next part --------------
A non-text attachment was scrubbed...
Name: ap_sta_WiFi6.pcap
Type: application/vnd.tcpdump.pcap
Size: 8156 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/hostap/attachments/20200908/3245908c/attachment-0001.pcap>