need help getting hostapd started, Intel Advanced-N 6205
Mike
debian at good-with-numbers.com
Sun Jan 7 22:02:18 PST 2018
Hostapd fails to start on a Debian stretch system against an Intel
Advanced-N 6205.
Debian package version is 2:2.4-1+deb9u1, amd64.
I've seen https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=885957
which is for the 2.6 release. I don't care about ACS in particular
(don't know if I should), just getting it to work at all would be
welcome.
-------------- next part --------------
# lspci -s 01: -v
01:00.0 Network controller: Intel Corporation Centrino Advanced-N 6205 [Taylor Peak] (rev 34)
Subsystem: Intel Corporation Centrino Advanced-N 6205 AGN
Flags: bus master, fast devsel, latency 0, IRQ 27
Memory at fe9fe000 (64-bit, non-prefetchable) [size=8K]
Capabilities: [c8] Power Management version 3
Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Capabilities: [e0] Express Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Device Serial Number ...
Kernel driver in use: iwlwifi
Kernel modules: iwlwifi
-------------- next part --------------
interface=wlan0
ssid="..."
country_code=US
ieee80211d=1
hw_mode=a
macaddr_acl=0
auth_algs=1
ignore_broadcast_ssid=0
wmm_enabled=1
ieee80211n=1
wpa=2
wpa_passphrase=...
wpa_key_mgmt=WPA-PSK WPA-PSK-SHA256
rsn_pairwise=CCMP
-------------- next part --------------
random: Trying to read entropy from /dev/random
Configuration file: /etc/hostapd/hostapd.conf
rfkill: initial event: idx=0 type=1 op=0 soft=0 hard=0
nl80211: Supported cipher 00-0f-ac:1
nl80211: Supported cipher 00-0f-ac:5
nl80211: Supported cipher 00-0f-ac:2
nl80211: Supported cipher 00-0f-ac:4
nl80211: Supported cipher 00-0f-ac:10
nl80211: Supported cipher 00-0f-ac:8
nl80211: Supported cipher 00-0f-ac:9
nl80211: Using driver-based off-channel TX
nl80211: interface wlan0 in phy phy0
nl80211: Set mode ifindex 5 iftype 3 (AP)
nl80211: Setup AP(wlan0) - device_ap_sme=0 use_monitor=0
nl80211: Subscribe to mgmt frames with AP handle 0x5625e7952a00
nl80211: Register frame type=0xb0 (WLAN_FC_STYPE_AUTH) nl_handle=0x5625e7952a00 match=
nl80211: Register frame type=0x0 (WLAN_FC_STYPE_ASSOC_REQ) nl_handle=0x5625e7952a00 match=
nl80211: Register frame type=0x20 (WLAN_FC_STYPE_REASSOC_REQ) nl_handle=0x5625e7952a00 match=
nl80211: Register frame type=0xa0 (WLAN_FC_STYPE_DISASSOC) nl_handle=0x5625e7952a00 match=
nl80211: Register frame type=0xc0 (WLAN_FC_STYPE_DEAUTH) nl_handle=0x5625e7952a00 match=
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x5625e7952a00 match=
nl80211: Register frame type=0x40 (WLAN_FC_STYPE_PROBE_REQ) nl_handle=0x5625e7952a00 match=
nl80211: Add own interface ifindex 5
nl80211: if_indices[16]: 5
phy: phy0
BSS count 1, BSSID mask 00:00:00:00:00:00 (0 bits)
wlan0: interface state UNINITIALIZED->COUNTRY_UPDATE
Previous country code US, new country code US
nl80211: Regulatory information - country=US (DFS-FCC)
nl80211: 2402-2472 @ 40 MHz 30 mBm
nl80211: 5170-5250 @ 80 MHz 23 mBm
nl80211: 5250-5330 @ 80 MHz 23 mBm (DFS)
nl80211: 5490-5730 @ 160 MHz 23 mBm (DFS)
nl80211: 5735-5835 @ 80 MHz 30 mBm
nl80211: 57240-63720 @ 2160 MHz 40 mBm
nl80211: Added 802.11b mode based on 802.11g information
ACS: Automatic channel selection started, this may take a bit
ACS: Scanning 1 / 5
wlan0: nl80211: scan request
Scan requested (ret=0) - scan timeout 10 seconds
wlan0: interface state COUNTRY_UPDATE->ACS
wlan0: ACS-STARTED
Interface initialization will be completed in a callback (ACS)
ctrl_iface not configured!
random: Got 20/20 bytes from /dev/random
RTM_NEWLINK: ifi_index=5 ifname=wlan0 operstate=2 linkmode=0 ifi_family=0 ifi_flags=0x1003 ([UP])
nl80211: Drv Event 33 (NL80211_CMD_TRIGGER_SCAN) received for wlan0
wlan0: nl80211: Scan trigger
wlan0: Event SCAN_STARTED (47) received
Unknown event 47
nl80211: Drv Event 34 (NL80211_CMD_NEW_SCAN_RESULTS) received for wlan0
wlan0: nl80211: New scan results available
nl80211: Scan included frequencies: 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 5180 5200 5220 5240 5260 5280 5300 5320 5500 5520 5540 5560 5580 5600 5620 5640 5660 5680 5700 5745 5765 5785 5805 5825
wlan0: Event SCAN_RESULTS (3) received
ACS: Using survey based algorithm (acs_num_scans=5)
nl80211: Fetch survey data
wlan0: Event SURVEY (46) received
No survey data received
ACS: Scanning 2 / 5
wlan0: nl80211: scan request
Scan requested (ret=0) - scan timeout 30 seconds
nl80211: Drv Event 33 (NL80211_CMD_TRIGGER_SCAN) received for wlan0
wlan0: nl80211: Scan trigger
wlan0: Event SCAN_STARTED (47) received
Unknown event 47
RTM_NEWLINK: ifi_index=5 ifname=wlan0 wext ifi_family=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK: ifi_index=5 ifname=wlan0 wext ifi_family=0 ifi_flags=0x1003 ([UP])
nl80211: Drv Event 34 (NL80211_CMD_NEW_SCAN_RESULTS) received for wlan0
wlan0: nl80211: New scan results available
nl80211: Scan included frequencies: 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 5180 5200 5220 5240 5260 5280 5300 5320 5500 5520 5540 5560 5580 5600 5620 5640 5660 5680 5700 5745 5765 5785 5805 5825
wlan0: Event SCAN_RESULTS (3) received
ACS: Using survey based algorithm (acs_num_scans=5)
nl80211: Fetch survey data
wlan0: Event SURVEY (46) received
No survey data received
ACS: Scanning 3 / 5
wlan0: nl80211: scan request
Scan requested (ret=0) - scan timeout 30 seconds
nl80211: Drv Event 33 (NL80211_CMD_TRIGGER_SCAN) received for wlan0
wlan0: nl80211: Scan trigger
wlan0: Event SCAN_STARTED (47) received
Unknown event 47
RTM_NEWLINK: ifi_index=5 ifname=wlan0 wext ifi_family=0 ifi_flags=0x1003 ([UP])
nl80211: Drv Event 34 (NL80211_CMD_NEW_SCAN_RESULTS) received for wlan0
wlan0: nl80211: New scan results available
nl80211: Scan included frequencies: 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 5180 5200 5220 5240 5260 5280 5300 5320 5500 5520 5540 5560 5580 5600 5620 5640 5660 5680 5700 5745 5765 5785 5805 5825
wlan0: Event SCAN_RESULTS (3) received
ACS: Using survey based algorithm (acs_num_scans=5)
nl80211: Fetch survey data
wlan0: Event SURVEY (46) received
No survey data received
ACS: Scanning 4 / 5
wlan0: nl80211: scan request
Scan requested (ret=0) - scan timeout 30 seconds
nl80211: Drv Event 33 (NL80211_CMD_TRIGGER_SCAN) received for wlan0
wlan0: nl80211: Scan trigger
wlan0: Event SCAN_STARTED (47) received
Unknown event 47
RTM_NEWLINK: ifi_index=5 ifname=wlan0 wext ifi_family=0 ifi_flags=0x1003 ([UP])
nl80211: Drv Event 34 (NL80211_CMD_NEW_SCAN_RESULTS) received for wlan0
wlan0: nl80211: New scan results available
nl80211: Scan included frequencies: 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 5180 5200 5220 5240 5260 5280 5300 5320 5500 5520 5540 5560 5580 5600 5620 5640 5660 5680 5700 5745 5765 5785 5805 5825
wlan0: Event SCAN_RESULTS (3) received
ACS: Using survey based algorithm (acs_num_scans=5)
nl80211: Fetch survey data
wlan0: Event SURVEY (46) received
No survey data received
ACS: Scanning 5 / 5
wlan0: nl80211: scan request
Scan requested (ret=0) - scan timeout 30 seconds
nl80211: Drv Event 33 (NL80211_CMD_TRIGGER_SCAN) received for wlan0
wlan0: nl80211: Scan trigger
wlan0: Event SCAN_STARTED (47) received
Unknown event 47
RTM_NEWLINK: ifi_index=5 ifname=wlan0 wext ifi_family=0 ifi_flags=0x1003 ([UP])
nl80211: Drv Event 34 (NL80211_CMD_NEW_SCAN_RESULTS) received for wlan0
wlan0: nl80211: New scan results available
nl80211: Scan included frequencies: 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 5180 5200 5220 5240 5260 5280 5300 5320 5500 5520 5540 5560 5580 5600 5620 5640 5660 5680 5700 5745 5765 5785 5805 5825
wlan0: Event SCAN_RESULTS (3) received
ACS: Using survey based algorithm (acs_num_scans=5)
nl80211: Fetch survey data
wlan0: Event SURVEY (46) received
No survey data received
ACS: Trying survey-based ACS
ACS: Unable to collect survey data
ACS: All study options have failed
Interface initialization failed
wlan0: interface state ACS->DISABLED
wlan0: AP-DISABLED
ACS: Possibly channel configuration is invalid, please report this along with your config file.
ACS: Failed to start
wlan0: AP-DISABLED
wlan0: Deauthenticate all stations
nl80211: send_mlme - da= ff:ff:ff:ff:ff:ff noack=0 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0xc0 (WLAN_FC_STYPE_DEAUTH) nlmode=3
nl80211: send_mlme -> send_frame
nl80211: send_frame - Use bss->freq=0
nl80211: send_frame -> send_frame_cmd
nl80211: Frame command failed: ret=-22 (Invalid argument) (freq=0 wait=0)
hostapd_free_hapd_data: Interface wlan0 wasn't started
hostapd_deinit_driver: driver=0x5625e7112d00 drv_priv=0x5625e79542d0 -> hapd_deinit
nl80211: deinit ifname=wlan0 disabled_11b_rates=0
nl80211: Remove monitor interface: refcount=0
nl80211: Remove beacon (ifindex=5)
netlink: Operstate: ifindex=5 linkmode=0 (kernel-control), operstate=6 (IF_OPER_UP)
nl80211: Set mode ifindex 5 iftype 2 (STATION)
nl80211: Teardown AP(wlan0) - device_ap_sme=0 use_monitor=0
nl80211: Unsubscribe mgmt frames handle 0x8888dead6f1da289 (AP teardown)
hostapd_deinit_driver:bss[0]->drv_priv=0x5625e79542d0
hostapd_cleanup_iface_partial(0x5625e7952000)
Interface wlan0 disabled
wlan0: interface state DISABLED->DISABLED
hostapd_interface_deinit_free(0x5625e7952000)
hostapd_interface_deinit_free: num_bss=1 conf->num_bss=1
hostapd_interface_deinit(0x5625e7952000)
wlan0: interface state DISABLED->DISABLED
hostapd_bss_deinit: deinit bss wlan0
wlan0: AP-DISABLED
hostapd_cleanup(hapd=0x5625e7953400 (wlan0))
hostapd_free_hapd_data: Interface wlan0 wasn't started
hostapd_interface_deinit_free: driver=0x5625e7112d00 drv_priv=(nil) -> hapd_deinit
hostapd_interface_free(0x5625e7952000)
hostapd_interface_free: free hapd 0x5625e7953400
hostapd_cleanup_iface(0x5625e7952000)
hostapd_cleanup_iface_partial(0x5625e7952000)
hostapd_cleanup_iface: free iface=0x5625e7952000
-------------- next part --------------
# iw list
Wiphy phy0
max # scan SSIDs: 20
max scan IEs length: 195 bytes
max # sched scan SSIDs: 0
max # match sets: 0
max # scan plans: 1
max scan plan interval: -1
max scan plan iterations: 0
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports RSN-IBSS.
Supported Ciphers:
* WEP40 (00-0f-ac:1)
* WEP104 (00-0f-ac:5)
* TKIP (00-0f-ac:2)
* CCMP-128 (00-0f-ac:4)
* CCMP-256 (00-0f-ac:10)
* GCMP-128 (00-0f-ac:8)
* GCMP-256 (00-0f-ac:9)
Available Antennas: TX 0 RX 0
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* monitor
Band 1:
Capabilities: 0x107e
HT20/HT40
SM Power Save disabled
RX Greenfield
RX HT20 SGI
RX HT40 SGI
No RX STBC
Max AMSDU length: 3839 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 4 usec (0x05)
HT Max RX data rate: 300 Mbps
HT TX/RX MCS rate indexes supported: 0-15
Bitrates (non-HT):
* 1.0 Mbps
* 2.0 Mbps (short preamble supported)
* 5.5 Mbps (short preamble supported)
* 11.0 Mbps (short preamble supported)
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Frequencies:
* 2412 MHz [1] (15.0 dBm)
* 2417 MHz [2] (15.0 dBm)
* 2422 MHz [3] (15.0 dBm)
* 2427 MHz [4] (15.0 dBm)
* 2432 MHz [5] (15.0 dBm)
* 2437 MHz [6] (15.0 dBm)
* 2442 MHz [7] (15.0 dBm)
* 2447 MHz [8] (15.0 dBm)
* 2452 MHz [9] (15.0 dBm)
* 2457 MHz [10] (15.0 dBm)
* 2462 MHz [11] (15.0 dBm)
* 2467 MHz [12] (disabled)
* 2472 MHz [13] (disabled)
Band 2:
Capabilities: 0x107e
HT20/HT40
SM Power Save disabled
RX Greenfield
RX HT20 SGI
RX HT40 SGI
No RX STBC
Max AMSDU length: 3839 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 4 usec (0x05)
HT Max RX data rate: 300 Mbps
HT TX/RX MCS rate indexes supported: 0-15
Bitrates (non-HT):
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Frequencies:
* 5180 MHz [36] (15.0 dBm) (no IR)
* 5200 MHz [40] (15.0 dBm) (no IR)
* 5220 MHz [44] (15.0 dBm) (no IR)
* 5240 MHz [48] (15.0 dBm) (no IR)
* 5260 MHz [52] (15.0 dBm) (no IR, radar detection)
* 5280 MHz [56] (15.0 dBm) (no IR, radar detection)
* 5300 MHz [60] (15.0 dBm) (no IR, radar detection)
* 5320 MHz [64] (15.0 dBm) (no IR, radar detection)
* 5500 MHz [100] (15.0 dBm) (no IR, radar detection)
* 5520 MHz [104] (15.0 dBm) (no IR, radar detection)
* 5540 MHz [108] (15.0 dBm) (no IR, radar detection)
* 5560 MHz [112] (15.0 dBm) (no IR, radar detection)
* 5580 MHz [116] (15.0 dBm) (no IR, radar detection)
* 5600 MHz [120] (15.0 dBm) (no IR, radar detection)
* 5620 MHz [124] (15.0 dBm) (no IR, radar detection)
* 5640 MHz [128] (15.0 dBm) (no IR, radar detection)
* 5660 MHz [132] (15.0 dBm) (no IR, radar detection)
* 5680 MHz [136] (15.0 dBm) (no IR, radar detection)
* 5700 MHz [140] (15.0 dBm) (no IR, radar detection)
* 5745 MHz [149] (15.0 dBm) (no IR)
* 5765 MHz [153] (15.0 dBm) (no IR)
* 5785 MHz [157] (15.0 dBm) (no IR)
* 5805 MHz [161] (15.0 dBm) (no IR)
* 5825 MHz [165] (15.0 dBm) (no IR)
Supported commands:
* new_interface
* set_interface
* new_key
* start_ap
* new_station
* new_mpath
* set_mesh_config
* set_bss
* authenticate
* associate
* deauthenticate
* disassociate
* join_ibss
* join_mesh
* set_tx_bitrate_mask
* frame
* frame_wait_cancel
* set_wiphy_netns
* set_channel
* set_wds_peer
* probe_client
* set_noack_map
* register_beacons
* start_p2p_device
* set_mcast_rate
* set_qos_map
* connect
* disconnect
Supported TX frame types:
* IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
Supported RX frame types:
* IBSS: 0x40 0xb0 0xc0 0xd0
* managed: 0x40 0xd0
* AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* mesh point: 0xb0 0xc0 0xd0
* P2P-client: 0x40 0xd0
* P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* P2P-device: 0x40 0xd0
WoWLAN support:
* wake up on disconnect
* wake up on magic packet
* wake up on pattern match, up to 20 patterns of 16-128 bytes,
maximum packet offset 0 bytes
* can do GTK rekeying
* wake up on GTK rekey failure
* wake up on EAP identity request
* wake up on rfkill release
software interface modes (can always be added):
* AP/VLAN
* monitor
valid interface combinations:
* #{ managed } <= 1, #{ AP } <= 1,
total <= 2, #channels <= 1, STA/AP BI must match
* #{ managed } <= 2,
total <= 2, #channels <= 1
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
Device supports TX status socket option.
Device supports HT-IBSS.
Device supports SAE with AUTHENTICATE command
Device supports scan flush.
Device supports per-vif TX power setting
Driver supports full state transitions for AP/GO clients
Driver supports a userspace MPM
Device supports static SMPS
Device supports dynamic SMPS
Device supports configuring vdev MAC-addr on create.
More information about the Hostap
mailing list