802.11r FT roam
Isaac Konikoff
isaac.konikoff at gmail.com
Thu Mar 3 13:20:40 PST 2016
My test has two hostapd AP's setup for 802.11r FT-EAP with a separate
hostapd radius server. A station can connect to either AP and when the
station is reset, it switches to the other AP. But I am unable to get
a roam to work.
I'm not sure I have completely correct configs (attached) for
802.11r...just tried to follow past examples I've found on this list.
The station 00:0e:8e:3d:30:e3 is connected to vap3 00:0e:8e:76:e6:71
then I issue a wpa_cli scan then roam to vap2 00:0e:8e:1c:c6:b5...the
hostapd log from vap2 shows:
1456965227.209282: FT: Send PMK-R1 pull request to remote R0KH address
00:0e:8e:76:e6:71
1456965227.209649: FT: RRB send to 00:0e:8e:76:e6:71
1456965227.209661: FT: Callback postponed until response is available
Below is a bit of the supplicant log.
Would any other logging help debug this?
Thanks for any suggestions,
Isaac
1456965227.187307: wlan1: Control interface command 'ROAM 00:0e:8e:1c:c6:b5'
1456965227.187351: wlan1: CTRL_IFACE ROAM 00:0e:8e:1c:c6:b5
1456965227.187378: wlan1: Considering connect request: reassociate: 1
selected: 00:0e:8e:1c:c6:b5 bssid: 00:0e:8e:76:e6:71 pending:
00:00:00:00:00:00 wpa_state: COMPLETED ssid=0xd50130
current_ssid=0xd50130
1456965227.187400: wlan1: Request association: reassociate: 1
selected: 00:0e:8e:1c:c6:b5 bssid: 00:0e:8e:76:e6:71 pending:
00:00:00:00:00:00 wpa_state: COMPLETED
1456965227.187410: wlan1: Re-association to the same ESS
1456965227.187420: TDLS: TDLS is allowed in the target BSS
1456965227.187427: TDLS: TDLS channel switch allowed in the target BSS
1456965227.187437: wlan1: Add radio work 'sme-connect'@0xd731b0
1456965227.187449: wlan1: First radio work item in the queue -
schedule start immediately
1456965227.187462: CTRL-DEBUG: ctrl_sock-sendto: sock=16 sndbuf=212992
outq=0 send_len=3
1456965227.187494: wlan1: Starting radio work 'sme-connect'@0xd731b0
after 0.000042 second wait
1456965227.187505: wlan1: Automatic auth_alg selection: 0x1
1456965227.187511: RSN: PMKSA cache search - network_ctx=0xd50130
try_opportunistic=0
1456965227.187516: RSN: Search for BSSID 00:0e:8e:1c:c6:b5
1456965227.187521: RSN: No PMKSA cache entry found
1456965227.187528: wlan1: RSN: using IEEE 802.11i/D9.0
1456965227.187535: wlan1: WPA: Selected cipher suites: group 8
pairwise 24 key_mgmt 32 proto 2
1456965227.187551: wlan1: WPA: clearing AP WPA IE
1456965227.187557: WPA: set AP RSN IE - hexdump(len=26): 30 18 01 00
00 0f ac 02 02 00 00 0f ac 04 00 0f ac 02 01 00 00 0f ac 03 0c 00
1456965227.187567: wlan1: WPA: using GTK TKIP
1456965227.187587: wlan1: WPA: using PTK CCMP
1456965227.187595: wlan1: WPA: using KEY_MGMT FT/802.1X
1456965227.187600: wlan1: WPA: not using MGMT group cipher
1456965227.187606: WPA: Set own WPA IE default - hexdump(len=22): 30
14 01 00 00 0f ac 02 01 00 00 0f ac 04 01 00 00 0f ac 03 00 00
1456965227.187615: FT: Mobility domain - hexdump(len=2): a1 a1
1456965227.187620: FT: Capability and Policy: 0x00
1456965227.187625: FT: Stored MDIE and FTIE from (Re)Association
Response - hexdump(len=5): 36 03 a1 a1 00
1456965227.188087: SME: FT IEs - hexdump(len=162): 30 26 01 00 00 0f
ac 02 01 00 00 0f ac 04 01 00 00 0f ac 03 00 00 01 00 27 04 07 d4 9d
26 13 8b 59 63 12 7e 91 eb fe bb 36 03 a1 a1 00 37 73 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50
e0 f5 12 77 94 d0 19 be 85 ba 0b 0e 74 4f 54 f7 82 08 31 3e 67 74 72
d7 00 dd 62 fe e7 1c 6d 03 1f 6e 61 73 2e 63 74 35 32 33 2d 33 6e 2d
66 32 30 2e 6c 61 6e 66 6f 72 67 65 2e 6c 6f 63 61 6c
1456965227.188121: wlan1: SME: Trying to use FT over-the-air
1456965227.188128: RRM: Determining whether RRM can be used - device
support: 0x0
1456965227.188133: RRM: No RRM in network
1456965227.188138: wlan1: Cancelling scan request
1456965227.188148: wlan1: SME: Trying to authenticate with
00:0e:8e:1c:c6:b5 (SSID='vap-ath9k' freq=5220 MHz)
1456965227.188166: wpa_driver_nl80211_set_key: ifindex=18 (wlan1)
alg=0 addr=(nil) key_idx=0 set_tx=0 seq_len=0 key_len=0
1456965227.188210: wpa_driver_nl80211_set_key: ifindex=18 (wlan1)
alg=0 addr=(nil) key_idx=1 set_tx=0 seq_len=0 key_len=0
1456965227.188260: wpa_driver_nl80211_set_key: ifindex=18 (wlan1)
alg=0 addr=0xd74150 key_idx=0 set_tx=0 seq_len=0 key_len=0
1456965227.188269: addr=00:0e:8e:1c:c6:b5
1456965227.188285: wlan1: State: COMPLETED -> AUTHENTICATING
1456965227.188291: nl80211: NL80211_CMD_SET_TX_BITRATE_MASK
(ifindex=18 ofdm-only: 0 cfg-legacy-mask: 0x80000fff is-advert: 0)
1456965227.188299: nl80211: Set TX Rates 5Ghz, i: 8
1456965227.188314: nl80211: NL80211_CMD_SET_TX_BITRATE_MASK
(ifindex=18 ofdm-only: 0 cfg-legacy-mask: 0x80000fff is-advert: 1)
1456965227.188321: nl80211: Set TX Rates 5Ghz, i: 8
1456965227.188334: WMM AC: WMM AC is disabled
1456965227.188342: EAPOL: External notification - EAP success=0
1456965227.188349: EAPOL: External notification - EAP fail=0
1456965227.188353: EAPOL: External notification - portControl=Auto
1456965227.188360: wlan1: Determining shared radio frequencies (max len 1)
1456965227.188367: wlan1: Shared frequencies (len=1): completed iteration
1456965227.188373: wlan1: freq[0]: 5220, flags=0x1
1456965227.188377: nl80211: NL80211_CMD_SET_TX_BITRATE_MASK
(ifindex=18 ofdm-only: 0 cfg-legacy-mask: 0x80000fff is-advert: 0)
1456965227.188384: nl80211: Set TX Rates 5Ghz, i: 8
1456965227.188396: nl80211: NL80211_CMD_SET_TX_BITRATE_MASK
(ifindex=18 ofdm-only: 0 cfg-legacy-mask: 0x80000fff is-advert: 1)
1456965227.188403: nl80211: Set TX Rates 5Ghz, i: 8
1456965227.188415: nl80211: Authenticate (ifindex=18)
1456965227.188421: * bssid=00:0e:8e:1c:c6:b5
1456965227.188426: * freq=5220
1456965227.188431: * SSID - hexdump_ascii(len=9):
76 61 70 2d 61 74 68 39 6b vap-ath9k
1456965227.188442: * IEs - hexdump(len=162): 30 26 01 00 00 0f ac 02
01 00 00 0f ac 04 01 00 00 0f ac 03 00 00 01 00 27 04 07 d4 9d 26 13
8b 59 63 12 7e 91 eb fe bb 36 03 a1 a1 00 37 73 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50 e0 f5
12 77 94 d0 19 be 85 ba 0b 0e 74 4f 54 f7 82 08 31 3e 67 74 72 d7 00
dd 62 fe e7 1c 6d 03 1f 6e 61 73 2e 63 74 35 32 33 2d 33 6e 2d 66 32
30 2e 6c 61 6e 66 6f 72 67 65 2e 6c 6f 63 61 6c
1456965227.188469: * Auth Type 2
1456965227.200744: nl80211: Authentication request send successfully
1456965227.200780: nl80211: Event message available
1456965227.200799: nl80211: Drv Event 20 (NL80211_CMD_DEL_STATION)
received for wlan1
1456965227.200813: nl80211: Delete station 00:0e:8e:76:e6:71
1456965227.200832: nl80211: Event message available
1456965227.200849: nl80211: Drv Event 39 (NL80211_CMD_DEAUTHENTICATE)
received for wlan1
1456965227.200860: nl80211: MLME event 39 (NL80211_CMD_DEAUTHENTICATE)
on wlan1(00:0e:8e:3d:30:e3) A1=00:0e:8e:76:e6:71 A2=00:0e:8e:3d:30:e3
1456965227.200877: nl80211: MLME event frame - hexdump(len=26): c0 00
00 00 00 0e 8e 76 e6 71 00 0e 8e 3d 30 e3 00 0e 8e 76 e6 71 00 00 01
00
1456965227.200891: nl80211: Deauthenticate event
1456965227.200898: nl80211: Ignore deauth/disassoc event from old AP
00:0e:8e:76:e6:71 when already authenticating with 00:0e:8e:1c:c6:b5
1456965227.200918: nl80211: Event message available
1456965227.200935: nl80211: Drv Event 48 (NL80211_CMD_DISCONNECT)
received for wlan1
1456965227.200946: nl80211: Ignore disconnect event when using userspace SME
1456965227.200959: nl80211: Event message available
1456965227.200973: nl80211: Drv Event 19 (NL80211_CMD_NEW_STATION)
received for wlan1
1456965227.200982: nl80211: New station 00:0e:8e:1c:c6:b5
1456965227.201224: RTM_NEWLINK: ifi_index=18 ifname=wlan1 operstate=2
linkmode=1 ifi_family=0 ifi_flags=0x1003 ([UP])
1456965227.201372: RTM_NEWLINK: ifi_index=18 ifname=wlan1 wext
ifi_family=0 ifi_flags=0x1043 ([UP][RUNNING])
1456965227.204055: nl80211: Event message available
1456965227.204098: nl80211: Drv Event 36 (NL80211_CMD_REG_CHANGE)
received for wlan1
1456965227.204111: nl80211: Regulatory domain change
1456965227.204118: * initiator=0
1456965227.204126: * type=1
1456965227.204135: wlan1: Event CHANNEL_LIST_CHANGED (28) received
1456965227.204147: wlan1: CTRL-EVENT-REGDOM-CHANGE init=CORE type=WORLD
1456965227.204156: wlan1: Updating hw mode
1456965227.204295: Available Antennas: TX 0x7 RX 0x7
1456965227.204309: Configured Antennas: TX 0x7 RX 0x7
1456965227.204386: nl80211: Regulatory information - country=00
1456965227.204396: nl80211: 2402-2472 @ 40 MHz 20 mBm
1456965227.204408: nl80211: 2457-2482 @ 40 MHz 20 mBm (no IR)
1456965227.204418: nl80211: 2474-2494 @ 20 MHz 20 mBm (no OFDM) (no IR)
1456965227.204428: nl80211: 5170-5250 @ 80 MHz 20 mBm (no IR)
1456965227.204437: nl80211: 5250-5330 @ 80 MHz 20 mBm (DFS) (no IR)
1456965227.204447: nl80211: 5490-5730 @ 160 MHz 20 mBm (DFS) (no IR)
1456965227.204457: nl80211: 5735-5835 @ 80 MHz 20 mBm (no IR)
1456965227.204472: nl80211: 57240-63720 @ 2160 MHz 0 mBm
1456965227.204502: nl80211: Added 802.11b mode based on 802.11g information
1456965227.208222: nl80211: Event message available
1456965227.208249: nl80211: Drv Event 36 (NL80211_CMD_REG_CHANGE)
received for wlan1
1456965227.208259: nl80211: Regulatory domain change
1456965227.208265: * initiator=1
1456965227.208271: * type=0
1456965227.208277: * alpha2=US
1456965227.208287: wlan1: Event CHANNEL_LIST_CHANGED (28) received
1456965227.208298: wlan1: CTRL-EVENT-REGDOM-CHANGE init=USER
type=COUNTRY alpha2=US
1456965227.208305: wlan1: Updating hw mode
1456965227.208437: Available Antennas: TX 0x7 RX 0x7
1456965227.208452: Configured Antennas: TX 0x7 RX 0x7
1456965227.208564: nl80211: Regulatory information - country=US (DFS-FCC)
1456965227.208590: nl80211: 2402-2472 @ 40 MHz 30 mBm
1456965227.208606: nl80211: 5170-5250 @ 80 MHz 17 mBm
1456965227.208616: nl80211: 5250-5330 @ 80 MHz 23 mBm (DFS)
1456965227.208626: nl80211: 5735-5835 @ 80 MHz 30 mBm
1456965227.208639: nl80211: 57240-63720 @ 2160 MHz 40 mBm
1456965227.208663: nl80211: Added 802.11b mode based on 802.11g information
1456965227.508759: nl80211: Event message available
1456965227.508807: nl80211: Drv Event 20 (NL80211_CMD_DEL_STATION)
received for wlan1
1456965227.508818: nl80211: Delete station 00:0e:8e:1c:c6:b5
1456965227.512228: nl80211: Event message available
1456965227.512256: nl80211: Drv Event 37 (NL80211_CMD_AUTHENTICATE)
received for wlan1
1456965227.512268: nl80211: MLME event 37; timeout with 00:0e:8e:1c:c6:b5
1456965227.512294: wlan1: Event AUTH_TIMED_OUT (14) received
1456965227.512306: wlan1: SME: Authentication timed out
1456965227.512325: wlan1: Radio work 'sme-connect'@0xd731b0 done in
0.324830 seconds
1456965227.512336: Added BSSID 00:0e:8e:1c:c6:b5 into blacklist
1456965227.512353: wlan1: Another BSS in this ESS has been seen; try it next
1456965227.512362: BSSID 00:0e:8e:1c:c6:b5 blacklist count incremented to 2
1456965227.512372: wlan1: Blacklist count 1 --> request scan in 100 ms
1456965227.512385: wlan1: Setting scan request: 0.100000 sec
1456965227.512398: wlan1: State: AUTHENTICATING -> DISCONNECTED
1456965227.512408: nl80211: NL80211_CMD_SET_TX_BITRATE_MASK
(ifindex=18 ofdm-only: 0 cfg-legacy-mask: 0x80000fff is-advert: 0)
1456965227.512422: nl80211: Set TX Rates 5Ghz, i: 8
1456965227.512460: nl80211: NL80211_CMD_SET_TX_BITRATE_MASK
(ifindex=18 ofdm-only: 0 cfg-legacy-mask: 0x80000fff is-advert: 1)
1456965227.512476: nl80211: Set TX Rates 5Ghz, i: 8
1456965227.512497: nl80211: Set wlan1 operstate 1->0 (DORMANT)
1456965227.512509: netlink: Operstate: ifindex=18 linkmode=-1 (no
change), operstate=5 (IF_OPER_DORMANT)
1456965227.512527: wlan1: SME: Remove mobility domain
1456965227.512537: EAPOL: External notification - portEnabled=0
1456965227.512545: EAPOL: SUPP_PAE entering state DISCONNECTED
1456965227.512553: EAPOL: Supplicant port status: Unauthorized
1456965227.512561: nl80211: Skip set_supp_port(unauthorized) while not
associated
1456965227.512568: EAPOL: SUPP_BE entering state INITIALIZE
1456965227.512605: EAP: EAP entering state DISABLED
1456965227.512614: EAPOL: External notification - portValid=0
1456965227.612403: wlan1: State: DISCONNECTED -> SCANNING
1456965227.612433: nl80211: NL80211_CMD_SET_TX_BITRATE_MASK
(ifindex=18 ofdm-only: 0 cfg-legacy-mask: 0x80000fff is-advert: 0)
1456965227.612447: nl80211: Set TX Rates 5Ghz, i: 8
1456965227.612476: nl80211: NL80211_CMD_SET_TX_BITRATE_MASK
(ifindex=18 ofdm-only: 0 cfg-legacy-mask: 0x80000fff is-advert: 1)
1456965227.612484: nl80211: Set TX Rates 5Ghz, i: 8
1456965227.612500: wlan1: Starting AP scan for wildcard SSID
1456965227.612544: wlan1: Optimize scan based on previously generated
frequency list
1456965227.612562: wlan1: trigger-scan, freqs: 0xd73f40
1456965227.612585: wlan1: Add radio work 'scan'@0xd731b0
1456965227.612601: wlan1: First radio work item in the queue -
schedule start immediately
1456965227.612624: wlan1: Starting radio work 'scan'@0xd731b0 after
0.000021 second wait
1456965227.612635: wlan1: nl80211: scan request
1456965227.612647: nl80211: Scan SSID - hexdump_ascii(len=0): [NULL]
1456965227.612654: nl80211: Scan extra IEs - hexdump(len=10): 7f 08 00
00 0a 02 01 00 00 40
1456965227.612661: nl80211: Scan frequency 5220 MHz
1456965227.618122: Scan requested (ret=0) - scan timeout 30 seconds
1456965227.618146: wlan1: trigger-scan-cb, assign work: 0xd731b0
1456965227.618162: nl80211: Event message available
1456965227.618174: nl80211: Drv Event 33 (NL80211_CMD_TRIGGER_SCAN)
received for wlan1
1456965227.618181: wlan1: nl80211: Scan trigger
1456965227.618189: wlan1: Event SCAN_STARTED (47) received
1456965227.618195: wlan1: Own scan request started a scan in 0.000051 seconds
1456965227.647818: RTM_NEWLINK: ifi_index=18 ifname=wlan1 wext
ifi_family=0 ifi_flags=0x1003 ([UP])
1456965227.647856: nl80211: Event message available
1456965227.647877: nl80211: Drv Event 34
(NL80211_CMD_NEW_SCAN_RESULTS) received for wlan1
1456965227.647888: wlan1: nl80211: New scan results available
1456965227.647900: nl80211: Scan probed for SSID ''
1456965227.647911: nl80211: Scan included frequencies: 5220
1456965227.647921: wlan1: Event SCAN_RESULTS (3) received
1456965227.647932: wlan1: Scan completed in 0.029735 seconds
1456965227.647995: nl80211: Received scan results (2 BSSes)
1456965227.648095: wlan1: BSS: Start scan result update 3
1456965227.648124: BSS: last_scan_res_used=2/32
1456965227.648138: wlan1: New scan results available (own=1 ext=0)
1456965227.648201: wlan1: Remove scan work, work: 0xd731b0 dbg: scan-results
1456965227.648226: wlan1: Radio work 'scan'@0xd731b0 done in 0.035602 seconds
1456965227.648234: wlan1: Selecting BSS from priority group 0
1456965227.648246: wlan1: 0: 00:0e:8e:76:e6:71 ssid='vap-ath9k'
wpa_ie_len=0 rsn_ie_len=24 caps=0x11 level=-9 freq=5220
1456965227.648260: wlan1: selected based on RSN IE
1456965227.648279: wlan1: selected BSS 00:0e:8e:76:e6:71 ssid='vap-ath9k'
1456965227.648302: wlan1: Considering connect request: reassociate: 0
selected: 00:0e:8e:76:e6:71 bssid: 00:00:00:00:00:00 pending:
00:00:00:00:00:00 wpa_state: SCANNING ssid=0xd50130
current_ssid=(nil)
1456965227.648324: wlan1: Request association: reassociate: 0
selected: 00:0e:8e:76:e6:71 bssid: 00:00:00:00:00:00 pending:
00:00:00:00:00:00 wpa_state: SCANNING
1456965227.648336: wlan1: Re-association to the same ESS
1456965227.648347: TDLS: TDLS is allowed in the target BSS
1456965227.648355: TDLS: TDLS channel switch allowed in the target BSS
1456965227.648365: wlan1: Add radio work 'sme-connect'@0xd731b0
1456965227.648377: wlan1: First radio work item in the queue -
schedule start immediately
1456965227.648394: RSN: Ignored PMKID candidate without preauth flag
1456965227.648419: wlan1: Starting radio work 'sme-connect'@0xd731b0
after 0.000040 second wait
1456965227.648435: wlan1: Automatic auth_alg selection: 0x1
1456965227.648445: RSN: PMKSA cache search - network_ctx=(nil)
try_opportunistic=0
1456965227.648453: RSN: Search for BSSID 00:0e:8e:76:e6:71
1456965227.648461: RSN: No PMKSA cache entry found
1456965227.648471: wlan1: RSN: using IEEE 802.11i/D9.0
1456965227.648478: wlan1: WPA: Selected cipher suites: group 8
pairwise 24 key_mgmt 32 proto 2
1456965227.648484: wlan1: WPA: clearing AP WPA IE
1456965227.648489: WPA: set AP RSN IE - hexdump(len=26): 30 18 01 00
00 0f ac 02 02 00 00 0f ac 04 00 0f ac 02 01 00 00 0f ac 03 0c 00
1456965227.648500: wlan1: WPA: using GTK TKIP
1456965227.648506: wlan1: WPA: using PTK CCMP
1456965227.648511: wlan1: WPA: using KEY_MGMT FT/802.1X
1456965227.648516: wlan1: WPA: not using MGMT group cipher
1456965227.648522: WPA: Set own WPA IE default - hexdump(len=22): 30
14 01 00 00 0f ac 02 01 00 00 0f ac 04 01 00 00 0f ac 03 00 00
1456965227.648531: FT: Mobility domain - hexdump(len=2): a1 a1
1456965227.648536: FT: Capability and Policy: 0x00
1456965227.648540: FT: Stored MDIE and FTIE from (Re)Association
Response - hexdump(len=5): 36 03 a1 a1 00
1456965227.649215: SME: FT IEs - hexdump(len=162): 30 26 01 00 00 0f
ac 02 01 00 00 0f ac 04 01 00 00 0f ac 03 00 00 01 00 27 04 07 d4 9d
26 13 8b 59 63 12 7e 91 eb fe bb 36 03 a1 a1 00 37 73 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 89
e4 fb 42 e6 87 76 58 73 5b 10 9e 44 49 e3 bc 10 12 fc d5 95 3e 6f a6
5d b3 f5 b7 e8 ce 32 cf 03 1f 6e 61 73 2e 63 74 35 32 33 2d 33 6e 2d
66 32 30 2e 6c 61 6e 66 6f 72 67 65 2e 6c 6f 63 61 6c
1456965227.649281: RRM: Determining whether RRM can be used - device
support: 0x0
1456965227.649290: RRM: No RRM in network
1456965227.649300: wlan1: Cancelling scan request
1456965227.649317: wlan1: SME: Trying to authenticate with
00:0e:8e:76:e6:71 (SSID='vap-ath9k' freq=5220 MHz)
1456965227.649328: wlan1: State: SCANNING -> AUTHENTICATING
1456965227.649335: nl80211: NL80211_CMD_SET_TX_BITRATE_MASK
(ifindex=18 ofdm-only: 0 cfg-legacy-mask: 0x80000fff is-advert: 0)
1456965227.649350: nl80211: Set TX Rates 5Ghz, i: 8
1456965227.649384: nl80211: NL80211_CMD_SET_TX_BITRATE_MASK
(ifindex=18 ofdm-only: 0 cfg-legacy-mask: 0x80000fff is-advert: 1)
1456965227.649400: nl80211: Set TX Rates 5Ghz, i: 8
1456965227.649425: EAPOL: External notification - EAP success=0
1456965227.649440: EAPOL: External notification - EAP fail=0
1456965227.649451: EAPOL: External notification - portControl=Auto
1456965227.649463: wlan1: Determining shared radio frequencies (max len 1)
1456965227.649474: wlan1: Shared frequencies (len=0): completed iteration
1456965227.649482: nl80211: NL80211_CMD_SET_TX_BITRATE_MASK
(ifindex=18 ofdm-only: 0 cfg-legacy-mask: 0x80000fff is-advert: 0)
1456965227.649504: nl80211: Set TX Rates 5Ghz, i: 8
1456965227.649529: nl80211: NL80211_CMD_SET_TX_BITRATE_MASK
(ifindex=18 ofdm-only: 0 cfg-legacy-mask: 0x80000fff is-advert: 1)
1456965227.649544: nl80211: Set TX Rates 5Ghz, i: 8
1456965227.649563: nl80211: Authenticate (ifindex=18)
1456965227.649583: * bssid=00:0e:8e:76:e6:71
1456965227.649595: * freq=5220
1456965227.649601: * SSID - hexdump_ascii(len=9):
76 61 70 2d 61 74 68 39 6b vap-ath9k
1456965227.649621: * IEs - hexdump(len=0): [NULL]
1456965227.649629: * Auth Type 0
1456965227.656800: nl80211: Authentication request send successfully
1456965227.656833: nl80211: Event message available
1456965227.656849: nl80211: Drv Event 19 (NL80211_CMD_NEW_STATION)
received for wlan1
1456965227.656861: nl80211: New station 00:0e:8e:76:e6:71
-------------- next part --------------
A non-text attachment was scrubbed...
Name: hostapd_vap2_R.conf
Type: application/octet-stream
Size: 1593 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/hostap/attachments/20160303/7e4f16db/attachment.obj>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: hostapd_vap3_R.conf
Type: application/octet-stream
Size: 1592 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/hostap/attachments/20160303/7e4f16db/attachment-0001.obj>
More information about the Hostap
mailing list