Marvell 8686 with wpa-supplicant problem ...

[Dan Williams]

On Thu, 2007-11-01 at 10:33 +0800, ScottLiu wrote:
>  
> 
> Hi folks,
> 
>  
> 
> I?m new to the wpa_supplicant. I tried to run wpa_supplicant 0.6.0
> (openssl 9.8e) with Marvell8686 SDIO wifi chip, but fail.
> 
> I know Marvell8686 works on Linux Kernel 2.6 above but I porting it to
> 2.4 Kenrel for some specific needs.

Are you using the Marvell reference driver, or the upstream 2.6 kernel
driver?

Dan

> Most function is just fine unless with wpa_supplicant, below is error
> logs,
> 
>  
> 
> # ./wpa_supplicant -c/etc/wpa_supplicant.conf  -iwl0
> 
> ioctl[SIOCSIWPMKSA]: Invalid argument
> 
> Enter wlan_setwpaie_ioctl
> 
> failed to copy WPA IE
> 
> ioctl[PRISM2_IOCTL_PRISM2_PARAM]: Bad addressEnter wlan_setwpaie_ioctl
> 
>  
> 
> failed to copy WPA IE
> 
> ioctl[PRISM2_IOCTL_PRISM2_PARAM]: Bad address
> 
> ioctl[PRISM2_IOCTL_HOSTAPD]: IEnter wlan_setwpaie_ioctl
> 
> nvalid argument
> 
> Failed to set encryption.
> 
> ioctl[PRISM2_IOCTL_Hret = 0
> 
> OSTAPD]: Invalid argument
> 
> Failed to set encryption.
> 
> ioctl[PRISEnter wlan_setwpaie_ioctl
> 
> M2_IOCTL_HOSTAPD]: Invalid argument
> 
> Failed to set encryption.
> 
> failed to copy WPA IE
> 
> ioctl[PRISM2_IOCTL_HOSTAPD]: Invalid argument
> 
> Failed to set encryption.
> 
> ioctl[PRISM2_IOCTL_PRISM2_PARAM]: Bad address
> 
> Trying to associate with 00:50:18:21:b4:f5 (SSID='Repeat_Scott' Enter
> wlan_setwpaie_ioctl
> 
> freq=2437 MHz)
> 
> failed to copy WPA IE
> 
> ioctl[PRISM2_IOCTL_PRISM2_PARAM]: Bad addressEnter wlan_setwpaie_ioctl
> 
>  
> 
> failed to copy WPA IE
> 
> ioctl[PRISM2_IOCTL_PRISM2_PARAM]: Bad addressEnter wlan_setwpaie_ioctl
> 
>  
> 
> failed to copy WPA IE
> 
> ioctl[PRISM2_IOCTL_PRISM2_PARAM]: Bad address
> 
> ioctl[PRISM2_IOCTL_HOSTAPD]: Invalid argument
> 
> ioctl[SIOCSIWFREQ]: Operation not supported
> 
> ioctl[SIOCSIWESSID]: Connection refused
> 
> ioctl[SIOCSIWAP]: Network is unrEnter wlan_setwpaie_ioctl
> 
> eachable
> 
> ret = 0
> 
> Association request to the driver failed
> 
> CTRL-EVENT-TERMINATING - signal 2 received
> 
> ioctl[PRISM2_IOCTL_HOSTAPD]: InvEnter wlan_setwpaie_ioctl
> 
> alid argument
> 
> ret = 0
> 
> Enter wlan_setwpaie_ioctl
> 
> ret = 0
> 
> Enter wlan_setwpaie_ioctl
> 
> ret = 0
> 
> Enter wlan_setwpaie_ioctl
> 
> ret = 0
> 
> ioctl[SIOCSIWAP]: Network is unreachable
> 
>  
> 
> Please help me on this, any suggestion would be appreciation.
> 
>  
> 
> Scott
> 
>  
> 
> 
> _______________________________________________
> HostAP mailing list
> HostAP at shmoo.com
> http://lists.shmoo.com/mailman/listinfo/hostap