wpa_supplicant && mandriva 2007

[Dan Williams]

On Tue, 2006-10-31 at 16:10 -0600, robm wrote:
> hey Dan that seemed to fix part of my problem , I now seem to be 
> authenticating using:
> #wpa_supplicant.conf
>  # IEEE 802.1X with dynamic WEP keys using EAP-PEAP/MSCHAPv2
> 
> ctrl_interface=/var/run/wpa_supplicant
> 
> network={
>         ssid="uofs"
>         key_mgmt=IEEE8021X
>         eap=PEAP
>         phase2="auth=MSCHAPV2"
>         identity="username"
>         password="password"
> }
> 
> 
> I authenticate but then get booted (then reauthed???) ? any insights?

You might have to capture some packets with a 3rd computer and post some
logs; Jouni would likely know what to check up on here.

Dan

> root at rob-laptop:/home/rob# wpa_supplicant -i eth2 -c 
> /etc/wpa_supplicant.conf -Dwext
> ioctl[SIOCSIWAUTH]: Operation not supported
> WEXT auth param 7 value 0x1 - ioctl[SIOCSIWAUTH]: Operation not supported
> WEXT auth param 4 value 0x0 - No network configuration found for the 
> current AP
> ioctl[SIOCSIWMLME]: Operation not supported
> CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys
> Trying to associate with 00:17:0f:e6:6c:b0 (SSID='uofs' freq=2437 MHz)
> ioctl[SIOCSIWGENIE]: Operation not supported
> Association request to the driver failed
> Associated with 00:17:0f:e6:6c:b0
> CTRL-EVENT-EAP-STARTED EAP authentication started
> CTRL-EVENT-EAP-METHOD EAP method 25 (PEAP) selected
> EAP-MSCHAPV2: Authentication succeeded
> EAP-TLV: TLV Result - Success - EAP-TLV/Phase2 Completed
> CTRL-EVENT-EAP-SUCCESS EAP authentication completed successfully
> Associated with 00:17:0f:e6:6c:b0
> CTRL-EVENT-EAP-STARTED EAP authentication started
> CTRL-EVENT-EAP-METHOD EAP method 25 (PEAP) selected
> EAP-TLV: TLV Result - Success - EAP-TLV/Phase2 Completed
> CTRL-EVENT-EAP-SUCCESS EAP authentication completed successfully
> CTRL-EVENT-CONNECTED - Connection to 00:17:0f:e6:6c:b0 completed (auth)
> Associated with 00:17:0f:e6:6c:b0
> CTRL-EVENT-EAP-STARTED EAP authentication started
> CTRL-EVENT-EAP-METHOD EAP method 25 (PEAP) selected
> EAP-TLV: TLV Result - Success - EAP-TLV/Phase2 Completed
> CTRL-EVENT-EAP-SUCCESS EAP authentication completed successfully
> CTRL-EVENT-CONNECTED - Connection to 00:17:0f:e6:6c:b0 completed (reauth)
> Associated with 00:17:0f:e6:6c:b0
> CTRL-EVENT-EAP-STARTED EAP authentication started
> CTRL-EVENT-EAP-METHOD EAP method 25 (PEAP) selected
> EAP-TLV: TLV Result - Success - EAP-TLV/Phase2 Completed
> CTRL-EVENT-EAP-SUCCESS EAP authentication completed successfully
> Associated with 00:17:0f:e6:6c:b0
> CTRL-EVENT-EAP-STARTED EAP authentication started
> CTRL-EVENT-EAP-METHOD EAP method 25 (PEAP) selected
> EAP-TLV: TLV Result - Success - EAP-TLV/Phase2 Completed
> CTRL-EVENT-EAP-SUCCESS EAP authentication completed successfully
> CTRL-EVENT-CONNECTED - Connection to 00:17:0f:e6:6c:b0 completed (reauth)
> CTRL-EVENT-TERMINATING - signal 2 received
> ioctl[SIOCSIWMLME]: Operation not supported
> ioctl[SIOCSIWAUTH]: Operation not supported
> WEXT auth param 4 value 0x0 - root at rob-laptop:/home/rob#
> 
> root at rob-laptop:/home/rob#
> 
> 
> 
> 
> 
> Dan Williams wrote:
> 
> >On Tue, 2006-10-24 at 23:02 -0600, robm wrote:
> >  
> >
> >>its  2.6.15-27-386  so I am a candidate for candidate for a kernel upgrade.
> >>    
> >>
> >
> >Note that the upgrade will only help your for airo right now.  But what
> >kind of card is your orinoco card?  Is it a hermes I card, or a prism2
> >or prism2.5 card?  If it's a hermes, you'll probably never get WPA :)
> >But if it's a prism2/2.5, you can use the hostap driver and you just
> >might.
> >
> >Dan
> >
> >  
> >
>