wpa with ndiswrapper problem

["Michael Höller"]

Hello,

<< sorry just saw that I missed the subject, here is the correct version
>>>

I am running SuSE 9.2 and have a working setup for a wlan with wep encr.
Now I thought beeing more secure and use WAP.

So I compiled wpa_supplicant-0.5.5 and followed the instructions from
the readme. Unfortunately I do not get a full success. I will add the
debugging output here maybe some one can point me to the correct
direction....

Thanks a lot
Michael


ws002:/media/usb-0981015050B2AABB:0:0:0p1/fuer_wap # wpa_supplicant
-iwlan0 -c/etc/wpa_supplicant.conf -Dndiswrapper -dd
Initializing interface 'wlan0' conf '/etc/wpa_supplicant.conf' driver
'ndiswrapper' ctrl_interface 'N/A' bridge 'N/A'
Configuration file '/etc/wpa_supplicant.conf' ->
'/etc/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant.conf'
Line: 1 - start of a new network block
ssid - hexdump_ascii(len=9):
     41 6b 61 7a 69 61 4e 65 74                        AkaziaNet      
PSK (ASCII passphrase) - hexdump_ascii(len=16): [REMOVED]
key_mgmt: 0x2
PSK (from passphrase) - hexdump(len=32): [REMOVED]
Priority group 0
   id=0 ssid='AkaziaNet'
Initializing interface (2) 'wlan0'
ioctl[SIOCSIWPMKSA]: No such device
SIOCGIWRANGE: too old (short) data - assuming WPA is not supported
WEXT: Operstate: linkmode=1, operstate=5
Own MAC address: 00:14:6c:31:a7:dd
wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
ioctl[SIOCSIWENCODEEXT]: No such device
Driver did not support SIOCSIWENCODEEXT, trying SIOCSIWENCODE
wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
ioctl[SIOCSIWENCODEEXT]: No such device
Driver did not support SIOCSIWENCODEEXT, trying SIOCSIWENCODE
wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
ioctl[SIOCSIWENCODEEXT]: No such device
Driver did not support SIOCSIWENCODEEXT, trying SIOCSIWENCODE
wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
ioctl[SIOCSIWENCODEEXT]: No such device
Driver did not support SIOCSIWENCODEEXT, trying SIOCSIWENCODE
Setting scan request: 0 sec 100000 usec
Added interface wlan0
RTM_NEWLINK: operstate=0 ifi_flags=0x1002 ()
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK: operstate=0 ifi_flags=0x1043 ([UP][RUNNING])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
RTM_NEWLINK: operstate=0 ifi_flags=0x1043 ([UP][RUNNING])
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b2a len=12
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b2a len=12
RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
Wireless event: cmd=0x8b2a len=12
State: DISCONNECTED -> SCANNING
Starting AP scan (broadcast SSID)
Trying to get current scan results first without requesting a new scan
to speed up initial association
Received 500 bytes of scan results (2 BSSes)
Scan results: 2
Selecting BSS from priority group 0
0: 00:14:6c:4c:dc:d0 ssid='AkaziaNet' wpa_ie_len=0 rsn_ie_len=0
caps=0x11
   skip - no WPA/RSN IE
1: 02:14:6c:4c:dc:d0 ssid='AkaziaNet' wpa_ie_len=0 rsn_ie_len=0
caps=0x11
   skip - no WPA/RSN IE
No suitable AP found.
Setting scan request: 0 sec 0 usec
Starting AP scan (broadcast SSID)
CTRL-EVENT-TERMINATING - signal 2 received
Removing interface wlan0
State: SCANNING -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
No keys have been configured - skip key clearing
No keys have been configured - skip key clearing
WEXT: Operstate: linkmode=0, operstate=6
Cancelling scan request

No suitable AP found.
Setting scan request: 5 sec 0 usec
CTRL-EVENT-TERMINATING - signal 2 received
Removing interface wlan0
State: SCANNING -> DISCONNECTED
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
WEXT: Operstate: linkmode=-1, operstate=5
No keys have been configured - skip key clearing
No keys have been configured - skip key clearing
WEXT: Operstate: linkmode=0, operstate=6
Cancelling scan request