Newbie WPA Question
Jeremy
jc1111
Fri Feb 10 20:03:12 PST 2006
lspci -v
00:00.0 Host bridge: Cyrix Corporation PCI Master
Flags: bus master, medium devsel, latency 0
00:0b.0 Ethernet controller: National Semiconductor Corporation DP83815
(MacPhyter) Ethernet Controller
Subsystem: National Semiconductor Corporation DP83815 (MacPhyter)
Ethernet Controller
Flags: bus master, medium devsel, latency 64, IRQ 9
I/O ports at 1000 [size=256]
Memory at febf7000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [40] Power Management version 2
00:0c.0 Ethernet controller: National Semiconductor Corporation DP83815
(MacPhyter) Ethernet Controller
Subsystem: National Semiconductor Corporation DP83815 (MacPhyter)
Ethernet Controller
Flags: bus master, medium devsel, latency 64, IRQ 10
I/O ports at 1400 [size=256]
Memory at febf8000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [40] Power Management version 2
00:0d.0 CardBus bridge: Texas Instruments: Unknown device ac55 (rev 01)
Flags: bus master, medium devsel, latency 168, IRQ 11
Memory at febf9000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=01, subordinate=04, sec-latency=176
Memory window 0: 10000000-103ff000 (prefetchable)
Memory window 1: 10400000-107ff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
16-bit legacy interface ports at 0001
00:0d.1 CardBus bridge: Texas Instruments: Unknown device ac55 (rev 01)
Flags: bus master, medium devsel, latency 168, IRQ 11
Memory at febfa000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=05, subordinate=08, sec-latency=176
Memory window 0: 10800000-10bff000 (prefetchable)
Memory window 1: 10c00000-10fff000
I/O window 0: 00004800-000048ff
I/O window 1: 00004c00-00004cff
16-bit legacy interface ports at 0001
00:12.0 ISA bridge: National Semiconductor Corporation: Unknown device 0510
Subsystem: National Semiconductor Corporation: Unknown device 0500
Flags: bus master, medium devsel, latency 4
I/O ports at 1c00 [size=64]
I/O ports at 1c40 [size=64]
00:12.1 Bridge: National Semiconductor Corporation: Unknown device 0511
Subsystem: National Semiconductor Corporation: Unknown device 0501
Flags: medium devsel
I/O ports at 1800 [size=256]
00:12.2 IDE interface: National Semiconductor Corporation: Unknown device
0502 (rev 01) (prog-if 80 [Master])
Subsystem: National Semiconductor Corporation: Unknown device 0502
Flags: bus master, medium devsel, latency 0
I/O ports at 1cc0 [size=16]
00:12.3 Multimedia audio controller: National Semiconductor Corporation:
Unknown device 0503
Subsystem: National Semiconductor Corporation: Unknown device 0503
Flags: bus master, medium devsel, latency 0
Memory at febfb000 (32-bit, non-prefetchable) [size=4K]
00:12.4 VGA compatible controller: National Semiconductor Corporation:
Unknown device 0514 (rev 01) (prog-if 00 [VGA])
Subsystem: National Semiconductor Corporation: Unknown device 0504
Flags: medium devsel
Memory at febfc000 (32-bit, non-prefetchable) [size=4K]
Memory at febfd000 (32-bit, non-prefetchable) [size=4K]
Memory at febfe000 (32-bit, non-prefetchable) [size=4K]
00:12.5 Bridge: National Semiconductor Corporation: Unknown device 0515
Subsystem: National Semiconductor Corporation: Unknown device 0505
Flags: medium devsel
I/O ports at 1c80 [size=64]
00:13.0 USB Controller: Compaq Computer Corporation USB Open Host Controller
(rev 08) (prog-if 10 [OHCI])
Subsystem: Compaq Computer Corporation USB Open Host Controller
Flags: bus master, medium devsel, latency 64, IRQ 12
Memory at febff000 (32-bit, non-prefetchable) [size=4K]
05:00.0 USB Controller: Lucent Microelectronics: Unknown device 5802 (rev
10) (prog-if 10 [OHCI])
Subsystem: Lucent Microelectronics: Unknown device 5802
Flags: bus master, medium devsel, latency 64, IRQ 11
Memory at 10c00000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [50] Power Management version 2
Thanks!
> Jeremy wrote:
> > I am trying to set WPA on my stompbox router (debian sid). I have a
PCMCIA
> > Senao card EXT. When I run hostapd I get unrecognized option errors. I
want
> > to use WPA-PSK. Not sure exactly which settings to change. Sorry for the
> > newbie post. Any help or direction to some good docs to learn are
> > appreciated.
> >
> What is the output of : lspci -v
> > J. Fletcher
> >
> > _______________________________________________
> > HostAP mailing list
> > HostAP at shmoo.com
> > http://lists.shmoo.com/mailman/listinfo/hostap
> >
> >
> >
>
>
>
>
>
>
>
> ___________________________________________________________
> Telefonate ohne weitere Kosten vom PC zum PC: http://messenger.yahoo.de
>
More information about the Hostap
mailing list