RT2500 WPA-EAP

[Ruzsinszky Attila]

Hi,

ASUS WL-107g card + ndiswrapper.
SSID is hidden.

wpa_supplicant.conf:
ctrl_interface=/var/run/wpa_supplicant
ctrl_interface_group=users
ap_scan=2

network={
        ssid="mySSID"
#        scan_ssid=1
        key_mgmt=WPA-PSK
        pairwise=TKIP
        group=TKIP
#       eap=TLS
        psk="11111111"
#       wep_key0="1111111111111"
#       wep_tx_keyidx=0
}

LNK is green and no ACT!

messages:
...
PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:02:00.0 to 64
ndiswrapper: using irq 11
wlan0: ndiswrapper ethernet device 00:0e:a6:ce:ee:97 using driver
rt2500, configuration file 1814:0201.5.conf
wlan0: encryption modes supported: WEP, WPA with TKIP, WPA with AES/CCMP
ndiswrapper (set_auth_mode:517): setting auth mode failed (C0010015)
ndiswrapper (set_auth_mode:517): setting auth mode failed (C0010015)
...

Initializing interface 'wlan0' conf 'test' driver 'ndiswrapper'
Configuration file 'test' -> '/home/rattila/test'
Reading configuration file '/home/rattila/test'
ctrl_interface='/var/run/wpa_supplicant'
ctrl_interface_group=100 (from group name 'users')
ap_scan=2
Priority group 0
   id=0 ssid='mySSID'
Initializing interface (2) 'wlan0'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
Own MAC address: 00:0e:a6:ce:ee:97
Setting scan request: 0 sec 100000 usec
Using existing control interface directory.
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
Trying to associate with SSID 'mySSID'
Cancelling scan request
Cancelling scan request
Automatic auth_alg selection: 0x1
WPA: Set cipher suites based on configuration
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 2
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT WPA-PSK
WPA: Own WPA IE - hexdump(len=22): 30 14 01 00 00 0f ac 02 01 00 00 0f
ac 02 01 00 00 0f ac 02 00 00
No keys have been configured - skip key clearing
Setting authentication timeout: 5 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
Authentication with 00:00:00:00:00:00 timed out.
Added BSSID 00:00:00:00:00:00 into blacklist
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
Setting scan request: 0 sec 0 usec
Trying to associate with SSID 'mySSID'
...

My experince is: it is very hard start using RT2500 cards. Iwlist scanning is
all right. And that's all. :-(

I'd like using RT2500 for WPA Enterprise but WPA-PSK is unsuccessfull.

TIA,
Ruzsi