Stumpped, trying to get WPA to work on Ubuntu (Breezy)

Jay Strauss jjstrauss
Sun Nov 13 13:00:31 PST 2005


Hi,

I've had WPA working in the past, I've searched through all my old
posts to this list (as well as others).  But I'm stumpped.  Below is
how I have things configured and outputs of, what I think is relevent.
 Like in the subject, this is a fresh install of ubuntu (Breezy) on a
thinkpad A30 that I've been using to attach to a WPA access point.

I hope someone can shed some light.

Thanks
Jay

( I hope the output of my wpa_supplicant command isn't too obnoxious)

I've loaded:

apt-get wpasupplicant hostap-utils hostapd


root at ubuntu:/home/jstrauss# hostap_diag eth0
Host AP driver diagnostics information for 'eth0'

NICID: id=0x8013 v1.0.0 (PRISM II (2.5) Mini-PCI (SST parallel flash))
PRIID: id=0x0015 v1.1.1
STAID: id=0x001f v1.7.4 (station firmware)

root at ubuntu:/home/jstrauss# cat /etc/default/wpasupplicant | grep -v \#

ENABLED=1

OPTIONS="-w"

OPTIONS="-i eth0 -D hostap -c /etc/wpa_supplicant.conf"

root at ubuntu:/home/jstrauss# cat /etc/wpa_supplicant.conf | grep -v \#

ctrl_interface=/var/run/wpa_supplicant
ctrl_interface_group=0

eapol_version=1
ap_scan=1
fast_reauth=1

network={
        ssid="StayOffChannelOne"
        psk=b2ccd634e188f57bc861d07733c5a510b868d5f8df4cd319bb671ae5e6fe69f9
}


root at ubuntu:/home/jstrauss# cat /etc/network/interfaces | grep -v \#

auto lo
iface lo inet loopback

mapping hotplug
        script grep
        map eth1

iface eth1 inet dhcp

auto eth0
iface eth0 inet dhcp

root at ubuntu:/home/jstrauss# wpa_supplicant -ieth0 -Dhostap
-c/etc/wpa_supplicant.conf -d 2>&1

ioctl[SIOCSIWPMKSA]: Operation not supported
Initializing interface 'eth0' conf '/etc/wpa_supplicant.conf' driver 'hostap'
Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant.conf'
ctrl_interface='/var/run/wpa_supplicant'
ctrl_interface_group=0
eapol_version=1
ap_scan=1
fast_reauth=1
Priority group 0
   id=0 ssid='StayOffChannelOne'
Initializing interface (2) 'eth0'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
SIOCGIWRANGE: too old (short) data - assuming WPA is not supported
Own MAC address: 00:20:e0:89:8f:e2
wpa_driver_hostap_set_wpa: enabled=1
wpa_driver_hostap_set_key: alg=none key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_countermeasures: enabled=0
wpa_driver_hostap_set_drop_unencrypted: enabled=1
Setting scan request: 0 sec 100000 usec
Wireless event: cmd=0x8b06 len=8
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth0' added
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth0' added
State: DISCONNECTED -> SCANNING
Starting AP scan (broadcast SSID)
Wireless event: cmd=0x8b19 len=12
Received 1055 bytes of scan results (7 BSSes)
Scan results: 7
Selecting BSS from priority group 0
0: 00:13:10:88:68:d4 ssid='StayOffChannelOne' wpa_ie_len=24
rsn_ie_len=0 caps=0x11
   selected
Trying to associate with 00:13:10:88:68:d4 (SSID='StayOffChannelOne'
freq=2412 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
WPA: using IEEE 802.11i/D3.0
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 2
WPA: set AP WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2
02 01 00 00 50 f2 02 01 00 00 50 f2 02
WPA: clearing AP RSN IE
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT WPA-PSK
WPA: Set own WPA IE default - hexdump(len=24): dd 16 00 50 f2 01 01 00
00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
No keys have been configured - skip key clearing
wpa_driver_hostap_set_drop_unencrypted: enabled=1
State: SCANNING -> ASSOCIATING
wpa_driver_hostap_associate
Setting authentication timeout: 5 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
Wireless event: cmd=0x8b06 len=8
Wireless event: cmd=0x8b04 len=12
Wireless event: cmd=0x8b1a len=30
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:13:10:88:68:d4
State: ASSOCIATING -> ASSOCIATED
Associated to a new BSS: BSSID=00:13:10:88:68:d4
No keys have been configured - skip key clearing
Associated with 00:13:10:88:68:d4
WPA: Association event - clear replay counter
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
EAPOL: External notification - portEnabled=1
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: txStart
WPA: drop TX EAPOL in non-IEEE 802.1X mode (type=1 len=0)
EAPOL: SUPP_BE entering state IDLE
EAP: EAP entering state INITIALIZE
EAP: EAP entering state IDLE
Setting authentication timeout: 10 sec 0 usec
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth0' added
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:00:00:00:00:00
Setting scan request: 0 sec 100000 usec
Added BSSID 00:13:10:88:68:d4 into blacklist
State: ASSOCIATED -> DISCONNECTED
EAPOL: External notification - portEnabled=0
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys
wpa_driver_hostap_set_key: alg=none key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=0 set_tx=0 seq_len=0 key_len=0
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth0' added
State: DISCONNECTED -> SCANNING
Starting AP scan (broadcast SSID)
Wireless event: cmd=0x8b19 len=12
Received 820 bytes of scan results (7 BSSes)
Scan results: 7
Selecting BSS from priority group 0
0: 00:13:10:88:68:d4 ssid='StayOffChannelOne' wpa_ie_len=24
rsn_ie_len=0 caps=0x11
   selected
Trying to associate with 00:13:10:88:68:d4 (SSID='StayOffChannelOne'
freq=2412 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
WPA: using IEEE 802.11i/D3.0
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 2
WPA: set AP WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2
02 01 00 00 50 f2 02 01 00 00 50 f2 02
WPA: clearing AP RSN IE
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT WPA-PSK
WPA: Set own WPA IE default - hexdump(len=24): dd 16 00 50 f2 01 01 00
00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
No keys have been configured - skip key clearing
wpa_driver_hostap_set_drop_unencrypted: enabled=1
State: SCANNING -> ASSOCIATING
wpa_driver_hostap_associate
Setting authentication timeout: 5 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
Wireless event: cmd=0x8b06 len=8
Wireless event: cmd=0x8b04 len=12
Wireless event: cmd=0x8b1a len=30
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:13:10:88:68:d4
State: ASSOCIATING -> ASSOCIATED
Associated to a new BSS: BSSID=00:13:10:88:68:d4
No keys have been configured - skip key clearing
Associated with 00:13:10:88:68:d4
WPA: Association event - clear replay counter
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
EAPOL: External notification - portEnabled=1
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: txStart
WPA: drop TX EAPOL in non-IEEE 802.1X mode (type=1 len=0)
EAPOL: SUPP_BE entering state IDLE
EAP: EAP entering state INITIALIZE
EAP: EAP entering state IDLE
Setting authentication timeout: 10 sec 0 usec
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth0' added
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:00:00:00:00:00
Setting scan request: 0 sec 100000 usec
BSSID 00:13:10:88:68:d4 blacklist count incremented to 2
State: ASSOCIATED -> DISCONNECTED
EAPOL: External notification - portEnabled=0
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys
wpa_driver_hostap_set_key: alg=none key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=0 set_tx=0 seq_len=0 key_len=0
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth0' added
State: DISCONNECTED -> SCANNING
Starting AP scan (broadcast SSID)
Wireless event: cmd=0x8b19 len=12
Received 943 bytes of scan results (7 BSSes)
Scan results: 7
Selecting BSS from priority group 0
0: 00:13:10:88:68:d4 ssid='StayOffChannelOne' wpa_ie_len=24
rsn_ie_len=0 caps=0x11
   skip - blacklisted
1: 00:12:17:f0:52:e9 ssid='comcast' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
2: 00:13:10:eb:30:47 ssid='Faus2817' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
3: 00:0d:72:6e:6c:41 ssid='2WIRE890' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
4: 00:0f:66:3a:60:04 ssid='snowday' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
5: 00:13:10:b1:bf:f9 ssid='steve' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
6: 8a:00:33:22:9f:b9 ssid='hpsetup' wpa_ie_len=0 rsn_ie_len=0 caps=0x2
   skip - no WPA/RSN IE
No APs found - clear blacklist and try again
Removed BSSID 00:13:10:88:68:d4 from blacklist (clear)
Selecting BSS from priority group 0
0: 00:13:10:88:68:d4 ssid='StayOffChannelOne' wpa_ie_len=24
rsn_ie_len=0 caps=0x11
   selected
Trying to associate with 00:13:10:88:68:d4 (SSID='StayOffChannelOne'
freq=2412 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
WPA: using IEEE 802.11i/D3.0
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 2
WPA: set AP WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2
02 01 00 00 50 f2 02 01 00 00 50 f2 02
WPA: clearing AP RSN IE
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT WPA-PSK
WPA: Set own WPA IE default - hexdump(len=24): dd 16 00 50 f2 01 01 00
00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
No keys have been configured - skip key clearing
wpa_driver_hostap_set_drop_unencrypted: enabled=1
State: SCANNING -> ASSOCIATING
wpa_driver_hostap_associate
Setting authentication timeout: 5 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
Wireless event: cmd=0x8b06 len=8
Wireless event: cmd=0x8b04 len=12
Wireless event: cmd=0x8b1a len=30
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:13:10:88:68:d4
State: ASSOCIATING -> ASSOCIATED
Associated to a new BSS: BSSID=00:13:10:88:68:d4
No keys have been configured - skip key clearing
Associated with 00:13:10:88:68:d4
WPA: Association event - clear replay counter
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
EAPOL: External notification - portEnabled=1
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: txStart
WPA: drop TX EAPOL in non-IEEE 802.1X mode (type=1 len=0)
EAPOL: SUPP_BE entering state IDLE
EAP: EAP entering state INITIALIZE
EAP: EAP entering state IDLE
Setting authentication timeout: 10 sec 0 usec
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth0' added
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:00:00:00:00:00
Setting scan request: 0 sec 100000 usec
Added BSSID 00:13:10:88:68:d4 into blacklist
State: ASSOCIATED -> DISCONNECTED
EAPOL: External notification - portEnabled=0
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys
wpa_driver_hostap_set_key: alg=none key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=0 set_tx=0 seq_len=0 key_len=0
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth0' added
State: DISCONNECTED -> SCANNING
Starting AP scan (broadcast SSID)
Wireless event: cmd=0x8b19 len=12
Received 943 bytes of scan results (7 BSSes)
Scan results: 7
Selecting BSS from priority group 0
0: 00:13:10:88:68:d4 ssid='StayOffChannelOne' wpa_ie_len=24
rsn_ie_len=0 caps=0x11
   selected
Trying to associate with 00:13:10:88:68:d4 (SSID='StayOffChannelOne'
freq=2412 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
WPA: using IEEE 802.11i/D3.0
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 2
WPA: set AP WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2
02 01 00 00 50 f2 02 01 00 00 50 f2 02
WPA: clearing AP RSN IE
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT WPA-PSK
WPA: Set own WPA IE default - hexdump(len=24): dd 16 00 50 f2 01 01 00
00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
No keys have been configured - skip key clearing
wpa_driver_hostap_set_drop_unencrypted: enabled=1
State: SCANNING -> ASSOCIATING
wpa_driver_hostap_associate
Setting authentication timeout: 5 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
Wireless event: cmd=0x8b06 len=8
Wireless event: cmd=0x8b04 len=12
Wireless event: cmd=0x8b1a len=30
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:13:10:88:68:d4
State: ASSOCIATING -> ASSOCIATED
Associated to a new BSS: BSSID=00:13:10:88:68:d4
No keys have been configured - skip key clearing
Associated with 00:13:10:88:68:d4
WPA: Association event - clear replay counter
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
EAPOL: External notification - portEnabled=1
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: txStart
WPA: drop TX EAPOL in non-IEEE 802.1X mode (type=1 len=0)
EAPOL: SUPP_BE entering state IDLE
EAP: EAP entering state INITIALIZE
EAP: EAP entering state IDLE
Setting authentication timeout: 10 sec 0 usec
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth0' added
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:00:00:00:00:00
Setting scan request: 0 sec 100000 usec
BSSID 00:13:10:88:68:d4 blacklist count incremented to 2
State: ASSOCIATED -> DISCONNECTED
EAPOL: External notification - portEnabled=0
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys
wpa_driver_hostap_set_key: alg=none key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=0 set_tx=0 seq_len=0 key_len=0
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth0' added
State: DISCONNECTED -> SCANNING
Starting AP scan (broadcast SSID)
Wireless event: cmd=0x8b19 len=12
Received 943 bytes of scan results (7 BSSes)
Scan results: 7
Selecting BSS from priority group 0
0: 00:13:10:88:68:d4 ssid='StayOffChannelOne' wpa_ie_len=24
rsn_ie_len=0 caps=0x11
   skip - blacklisted
1: 00:12:17:f0:52:e9 ssid='comcast' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
2: 00:13:10:eb:30:47 ssid='Faus2817' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
3: 00:0f:66:3a:60:04 ssid='snowday' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
4: 00:0d:72:6e:6c:41 ssid='2WIRE890' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
5: 00:13:10:b1:bf:f9 ssid='steve' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
   skip - no WPA/RSN IE
6: 8a:00:33:22:9f:b9 ssid='hpsetup' wpa_ie_len=0 rsn_ie_len=0 caps=0x2
   skip - no WPA/RSN IE
No APs found - clear blacklist and try again
Removed BSSID 00:13:10:88:68:d4 from blacklist (clear)
Selecting BSS from priority group 0
0: 00:13:10:88:68:d4 ssid='StayOffChannelOne' wpa_ie_len=24
rsn_ie_len=0 caps=0x11
   selected
Trying to associate with 00:13:10:88:68:d4 (SSID='StayOffChannelOne'
freq=2412 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
WPA: using IEEE 802.11i/D3.0
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 2
WPA: set AP WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2
02 01 00 00 50 f2 02 01 00 00 50 f2 02
WPA: clearing AP RSN IE
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT WPA-PSK
WPA: Set own WPA IE default - hexdump(len=24): dd 16 00 50 f2 01 01 00
00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
No keys have been configured - skip key clearing
wpa_driver_hostap_set_drop_unencrypted: enabled=1
State: SCANNING -> ASSOCIATING
wpa_driver_hostap_associate
Setting authentication timeout: 5 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
Wireless event: cmd=0x8b06 len=8
Wireless event: cmd=0x8b04 len=12
Wireless event: cmd=0x8b1a len=30
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:13:10:88:68:d4
State: ASSOCIATING -> ASSOCIATED
Associated to a new BSS: BSSID=00:13:10:88:68:d4
No keys have been configured - skip key clearing
Associated with 00:13:10:88:68:d4
WPA: Association event - clear replay counter
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
EAPOL: External notification - portEnabled=1
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: txStart
WPA: drop TX EAPOL in non-IEEE 802.1X mode (type=1 len=0)
EAPOL: SUPP_BE entering state IDLE
EAP: EAP entering state INITIALIZE
EAP: EAP entering state IDLE
Setting authentication timeout: 10 sec 0 usec
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth0' added
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:00:00:00:00:00
Setting scan request: 0 sec 100000 usec
Added BSSID 00:13:10:88:68:d4 into blacklist
State: ASSOCIATED -> DISCONNECTED
EAPOL: External notification - portEnabled=0
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys
wpa_driver_hostap_set_key: alg=none key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=0 set_tx=0 seq_len=0 key_len=0
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth0' added
State: DISCONNECTED -> SCANNING
Starting AP scan (broadcast SSID)
Wireless event: cmd=0x8b19 len=12
Received 1125 bytes of scan results (8 BSSes)
Scan results: 8
Selecting BSS from priority group 0
0: 00:13:10:88:68:d4 ssid='StayOffChannelOne' wpa_ie_len=24
rsn_ie_len=0 caps=0x11
   selected
Trying to associate with 00:13:10:88:68:d4 (SSID='StayOffChannelOne'
freq=2412 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
WPA: using IEEE 802.11i/D3.0
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 2
WPA: set AP WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2
02 01 00 00 50 f2 02 01 00 00 50 f2 02
WPA: clearing AP RSN IE
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT WPA-PSK
WPA: Set own WPA IE default - hexdump(len=24): dd 16 00 50 f2 01 01 00
00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
No keys have been configured - skip key clearing
wpa_driver_hostap_set_drop_unencrypted: enabled=1
State: SCANNING -> ASSOCIATING
wpa_driver_hostap_associate
Setting authentication timeout: 5 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
Wireless event: cmd=0x8b06 len=8
Wireless event: cmd=0x8b04 len=12
Wireless event: cmd=0x8b1a len=30
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:13:10:88:68:d4
State: ASSOCIATING -> ASSOCIATED
Associated to a new BSS: BSSID=00:13:10:88:68:d4
No keys have been configured - skip key clearing
Associated with 00:13:10:88:68:d4
WPA: Association event - clear replay counter
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
EAPOL: External notification - portEnabled=1
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: txStart
WPA: drop TX EAPOL in non-IEEE 802.1X mode (type=1 len=0)
EAPOL: SUPP_BE entering state IDLE
EAP: EAP entering state INITIALIZE
EAP: EAP entering state IDLE
Setting authentication timeout: 10 sec 0 usec
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth0' added
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:00:00:00:00:00
Setting scan request: 0 sec 100000 usec
BSSID 00:13:10:88:68:d4 blacklist count incremented to 2
State: ASSOCIATED -> DISCONNECTED
EAPOL: External notification - portEnabled=0
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portValid=0
EAPOL: External notification - EAP success=0
CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys
wpa_driver_hostap_set_key: alg=none key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=0 set_tx=0 seq_len=0 key_len=0
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth0' added




More information about the Hostap mailing list