RICOH bridge and SENAO==>HOSTAP_cs:initalisation failed, prism2_config() failed
gaurav dawra
openapproject
Mon Jun 14 23:53:33 PDT 2004
Hi
I am trying to configure my senao 2511 CD EXT2 with RICOH chipset based PCI
to PCMCIA brdige.
I can modprobe i82365 ,pcmcia_core (installed using pcmcia-cs-3.2.7 package)
and ds modules.
when i do lsmod:
[root at openap root]# lsmod
Module Size Used by Not tainted
ds 8264 0 (unused)
i82365 38208 1
pcmcia_core 45184 0 [ds i82365]
-----------------------------------------------------------------
I do dmesg everything is fine: bridge is detected.
Linux PCMCIA Card Services 3.2.7
kernel build: 2.4.20rn #5 SMP Mon Jun 14 10:47:01 MDT 2004
options: [pci] [cardbus] [apm]
Intel ISA/PCI/CardBus PCIC probe:
Ricoh RL5C475 rev 80 PCI-to-CardBus at slot 00:14, mem 0xe3001000
host opts [0]: [isa irq] [io 3/6/1] [mem 3/6/1] [pci irq 5] [lat 32/32]
[bus 2/2]
ISA irqs (default) = 4,7,9 PCI status changes
--------------------------------------------------------------------
Now i have SENAO 2511CD EXT2 card. I loaded the hostap modules using NEW
released ( hostap-driver-0.2.2)
[root at openap hostap-driver-0.2.2]# ls
ChangeLog COPYING driver kernel-patches Makefile pcmcia-cs-patches
README
I did make clean; make all; make install
------------------------------------------------------------------------
Now when i start the "cardmgr" by command "/etc/init.d/pcmcia restart"
[root at openap hostap-driver-0.2.2]# /etc/init.d/pcmcia restart
Shutting down PCMCIA services: done.
Starting PCMCIA services: cardmgr[1995]: watching 1 socket
done.
[root at openap hostap-driver-0.2.2]# lsmod
Module Size Used by Not tainted
hostap_cs 47124 0 (unused)
hostap 102440 0 [hostap_cs]
ds 8264 1 [hostap_cs]
i82365 38208 1
pcmcia_core 45184 0 [hostap_cs ds i82365]
[root at openap hostap-driver-0.2.2]#
--------------------------------------------------------------------------
lsmod shows me the hostap_cs driver is loaded: ALLRIGHT
now when i do :"iwconfig"
[root at openap hostap-driver-0.2.2]# iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
dummy0 no wireless extensions.
sit0 no wireless extensions.
Warning: Driver for device wifi0 has been compiled with version 14
of Wireless Extension, while this program is using version 15.
Some things may be broken...
wifi0 IEEE 802.11-DS ESSID:"test"
Mode:Master
Encryption key:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
-------------------------------------------------------------------------------------------------
And when i do "dmesg" this comes:
hostap_crypt: registered algorithm 'NULL'
hostap_cs: 0.2.2 - 2004-05-31 (Jouni Malinen <jkmaline at cc.hut.fi>)
hostap_cs: setting Vcc=33 (constant)
hostap_cs: CS_EVENT_CARD_INSERTION
hostap_cs: setting Vcc=33 (from config)
Checking CFTABLE_ENTRY 0x01 (default 0x01)
IO window settings: cfg->io.nwin=1 dflt.io.nwin=1
io->flags = 0x0046, io.base=0x0000, len=64
cs: IO port probe 0x0100-0x04ff: excluding 0x200-0x207 0x378-0x37f
0x3c0-0x3df 0x4d0-0x4d7
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0a00-0x0aff: clean.
cs: IO port probe 0x0c00-0x0cff: clean.
hostap_cs: Registered netdevice wifi0
hostap_cs: index 0x01: Vcc 3.3, irq 9, io 0x0100-0x013f
prism2_hw_init: initialized in 190 ms
wifi0: hfa384x_cmd: entry still in list? (entry=c33dc1e0, type=0, res=0)
wifi0: hfa384x_cmd: command was not completed (res=0, entry=c33dc1e0,
type=0, cmd=0x0021, param0=0xfd0b, EVSTAT=8010 INTEN=0010)
wifi0: interrupt delivery does not seem to work
wifi0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fd0b, len=8)
Could not get RID for component NIC
hostap_cs: Initialization failed
prism2_config() failed
wifi0: hfa384x_cmd: entry still in list? (entry=c33dc1e0, type=0, res=0)
wifi0: hfa384x_cmd: command was not completed (res=0, entry=c33dc1e0,
type=0, cmd=0x0021, param0=0xfdc6, EVSTAT=8010 INTEN=0000)
wifi0: interrupt delivery does not seem to work
wifi0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fdc6, len=12)
wifi0: hfa384x_cmd: entry still in list? (entry=c33dc1e0, type=0, res=0)
wifi0: hfa384x_cmd: command was not completed (res=0, entry=c33dc1e0,
type=0, cmd=0x0021, param0=0xfdc6, EVSTAT=8010 INTEN=0000)
wifi0: interrupt delivery does not seem to work
wifi0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fdc6, len=12)
wifi0: hfa384x_cmd_issue: cmd reg was busy for 5000 usec
wifi0: hfa384x_cmd_issue - timeout - reg=0x8021
wifi0: hfa384x_cmd: entry still in list? (entry=c33dc1e0, type=0, res=-1)
wifi0: hfa384x_cmd: interrupted; err=-110
wifi0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fdc1, len=2)
wifi0: hfa384x_cmd_issue: cmd reg was busy for 5000 usec
wifi0: hfa384x_cmd_issue - timeout - reg=0x8021
wifi0: hfa384x_cmd: entry still in list? (entry=c33dc1e0, type=0, res=-1)
wifi0: hfa384x_cmd: interrupted; err=-110
wifi0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fc06, len=2)
wifi0: hfa384x_cmd_issue: cmd reg was busy for 5000 usec
wifi0: hfa384x_cmd_issue - timeout - reg=0x8021
wifi0: hfa384x_cmd: entry still in list? (entry=c33dc1e0, type=0, res=-1)
wifi0: hfa384x_cmd: interrupted; err=-110
wifi0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fd42, len=6)
wifi0: hfa384x_cmd_issue: cmd reg was busy for 5000 usec
wifi0: hfa384x_cmd_issue - timeout - reg=0x8021
wifi0: hfa384x_cmd: entry still in list? (entry=c7044230, type=0, res=-1)
wifi0: hfa384x_cmd: interrupted; err=-110
wifi0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fc0e, len=34)
wifi0: hfa384x_cmd_issue: cmd reg was busy for 5000 usec
wifi0: hfa384x_cmd_issue - timeout - reg=0x8021
wifi0: hfa384x_cmd: entry still in list? (entry=c33dc1e0, type=0, res=-1)
wifi0: hfa384x_cmd: interrupted; err=-110
wifi0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fc84, len=2)
wifi0: hfa384x_cmd_issue: cmd reg was busy for 5000 usec
wifi0: hfa384x_cmd_issue - timeout - reg=0x8021
wifi0: hfa384x_cmd: entry still in list? (entry=c33dc1e0, type=0, res=-1)
wifi0: hfa384x_cmd: interrupted; err=-110
wifi0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fc83, len=2)
wifi0: hfa384x_cmd_issue: cmd reg was busy for 5000 usec
wifi0: hfa384x_cmd_issue - timeout - reg=0x8021
wifi0: hfa384x_cmd: entry still in list? (entry=c33dc1e0, type=0, res=-1)
wifi0: hfa384x_cmd: interrupted; err=-110
wifi0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fc82, len=2)
wifi0: hfa384x_cmd_issue: cmd reg was busy for 5000 usec
wifi0: hfa384x_cmd_issue - timeout - reg=0x8021
wifi0: hfa384x_cmd: entry still in list? (entry=c33dc1e0, type=0, res=-1)
wifi0: hfa384x_cmd: interrupted; err=-110
wifi0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fc09, len=2)
wifi0: hfa384x_cmd_issue: cmd reg was busy for 5000 usec
wifi0: hfa384x_cmd_issue - timeout - reg=0x8021
wifi0: hfa384x_cmd: entry still in list? (entry=c33dc1e0, type=0, res=-1)
wifi0: hfa384x_cmd: interrupted; err=-110
wifi0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fd48, len=2)
------------------------------------------------------------------------------------------------------------
NOw FYI i have configured this card with the same bridge with the HOSTAP
driver only . I have also tried to configure using the "hostap-driver-0.2.1"
also.
I do not know what is happening here.
wifi0: interrupt delivery does not seem to work
wifi0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fd0b, len=8)
Could not get RID for component NIC
hostap_cs: Initialization failed
prism2_config() failed
Please suggest what i am doing wrong. I have read quite a good number of
postings on the internet, but no real HINT. I have also read some postings
from pavel, they were helpful but this is a NEW ERROR for me.
Thanx,
Gaurav
_________________________________________________________________
Is your PC infected? Get a FREE online computer virus scan from McAfee?
Security. http://clinic.mcafee.com/clinic/ibuy/campaign.asp?cid=3963
More information about the Hostap
mailing list