PCI: No IRQ known for interrupt pin A of device 02:07.0
Brian Sturgill
zen_hacker
Thu Jul 29 19:21:30 PDT 2004
Try switching pci slots with the card. Some machines assign irq's to the pci
slots.
Brian
>From: "gaurav dawra" <openapproject at hotmail.com>
>To: hostap at shmoo.com
>Subject: PCI: No IRQ known for interrupt pin A of device 02:07.0
>Date: Thu, 29 Jul 2004 23:32:01 +0000
>
>Hi
>
>I am trying to confiure my 'cardbus' PCI-->PCMCIA bridge(Ricoh Chipset). I
>am trying it on Dell optiplex with bios A02.
>
>You can see that in "lspci".
>00:1f.2 IDE interface: Intel Corp.: Unknown device 24d1 (rev 02)
>00:1f.3 SMBus: Intel Corp. 82801EB SMBus (rev 02)
>00:1f.5 Multimedia audio controller: Intel Corp. 82801EB AC'97 Audio (rev
>02)
>01:00.0 VGA compatible controller: nVidia Corporation NV18 [GeForce4 MX 440
>AGP 8x] (rev a2)
>==>02:07.0 CardBus bridge: Ricoh Co Ltd RL5c475 (rev 80)<===
>02:0c.0 Ethernet controller: Intel Corp. 82540EM Gigabit Ethernet
>Controller (rev 02)
>
>I am using Yenta_Socket and ds for it to load the bridge. But after
>starting the "service pcmcia start" i
>
>lsmod gives me this :
>
>Module Size Used by Not tainted
>ds 8840 1
>yenta_socket 12928 1
>pcmcia_core 54720 0 [ds yenta_socket]
>parport_pc 19108 1 (autoclean)
>
>[root at localhost isapnptools-1.26]# more /proc/interrupts
> CPU0
> 0: 370938 XT-PIC timer
> 1: 8846 XT-PIC keyboard
> 2: 0 XT-PIC cascade
> 8: 1 XT-PIC rtc
> 9: 54108 XT-PIC eth0
>12: 40376 XT-PIC PS/2 Mouse
>14: 21410 XT-PIC ide0
>15: 16 XT-PIC ide1
>NMI: 0
>ERR: 0
>
>see dmesg and this is what i get.
>
>parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
>parport0: irq 7 detected
>lp0: using parport0 (polling).
>lp0: console ready
>unloading Kernel Card Services
>Linux Kernel Card Services 3.1.22
> options: [pci] [cardbus] [pm]
>===>PCI: No IRQ known for interrupt pin A of device 02:07.0<====
>Yenta IRQ list 0000, PCI irq0
>Socket status: 30000006
>cs: IO port probe 0x0c00-0x0cff: excluding 0xc00-0xc7f
>cs: IO port probe 0x0100-0x04ff: excluding 0x4d0-0x4d7
>cs: IO port probe 0x0a00-0x0aff: clean.
>====================================
>hmm......I tried and read many posting on the internet about the same
>issue. Also the posting from linus, pavel and many others. It seems to me
>that linux is trying to find the irq for the ISA device and cud not find
>any and then just gives up. It says that 'try pci=biosirq' or pci=noapci, i
>tried that did lilo-v and rebooted the system still the same error stays :(
>
>Some posts mentioned to check the linux config file whether it is a pnp OS
>or not.
>
>#
># Plug and Play configuration
>#
>CONFIG_PNP=y
>CONFIG_ISAPNP=y
>
>#
># Block devices
>#
>CONFIG_BLK_DEV_FD=y
>CONFIG_BLK_DEV_XD=m
>CONFIG_PARIDE=m
>CONFIG_PARIDE_PARPORT=m
>
>So above 'clip' from the CONFIG file suggests that it is a PnP OS. So it
>should scans for all devices by itself and provide appropiate irq.
>
>According to this posting :
>http://david.dpitts.com/archives/000012.html
>
>It says that ' we have to set pnp OS in bios as NO' , Well in my DELL bios
>A02 there is no such entry, thanx to dell. So i cannot see whether BIOS is
>configuring the devices or not. Is this is a BIOS PROBLEM?
>
>
>I searched for many hours on the internet to find the solution of the
>problem. And tried all things which i could find in those postings. Am i
>heading towards the dead end in this case, somebody please guide me to the
>right direction.
>
>Some clue will be quite helpful. I am also mentioning output of ''lspci
>-vvx'" to look over.
>
>[root at localhost isapnptools-1.26]# lspci -vvx
>00:00.0 Host bridge: Intel Corp. 82865G [Springdale-G] Chipset Host Bridge
>(rev 02)
> Subsystem: Dell Computer Corporation: Unknown device 0151
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
>Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr-
>DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
> Latency: 0
> Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M]
> Capabilities: [e4] #09 [0106]
> Capabilities: [a0] AGP version 3.0
> Status: RQ=31 SBA+ 64bit- FW+ Rate=x1,x2
> Command: RQ=0 SBA+ AGP- 64bit- FW- Rate=<none>
>00: 86 80 70 25 06 01 90 20 02 00 00 06 00 00 00 00
>10: 08 00 00 e8 00 00 00 00 00 00 00 00 00 00 00 00
>20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 51 01
>30: 00 00 00 00 e4 00 00 00 00 00 00 00 00 00 00 00
>
>00:01.0 PCI bridge: Intel Corp.: Unknown device 2571 (rev 02) (prog-if 00
>[Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
>Stepping- SERR+ FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr-
>DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
> Memory behind bridge: fd000000-feafffff
> Prefetchable memory behind bridge: f0000000-f7ffffff
> BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
>00: 86 80 71 25 07 01 a0 00 02 00 04 06 00 40 01 00
>10: 00 00 00 00 00 00 00 00 00 01 01 40 f0 00 a0 22
>20: 00 fd a0 fe 00 f0 f0 f7 00 00 00 00 00 00 00 00
>30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 08 00
>
>00:1d.0 USB Controller: Intel Corp. 82801EB USB (Hub #1) (rev 02) (prog-if
>00 [UHCI])
> Subsystem: Dell Computer Corporation: Unknown device 0151
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
>Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr-
>DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin A routed to IRQ 11
> Region 4: I/O ports at ff80 [size=32]
>00: 86 80 d2 24 05 00 80 02 02 00 03 0c 00 00 80 00
>10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>20: 81 ff 00 00 00 00 00 00 00 00 00 00 28 10 51 01
>30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 00 00
>
>00:1d.1 USB Controller: Intel Corp. 82801EB USB (Hub #2) (rev 02) (prog-if
>00 [UHCI])
> Subsystem: Dell Computer Corporation: Unknown device 0151
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
>Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr-
>DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin B routed to IRQ 10
> Region 4: I/O ports at ff60 [size=32]
>00: 86 80 d4 24 05 00 80 02 02 00 03 0c 00 00 00 00
>10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>20: 61 ff 00 00 00 00 00 00 00 00 00 00 28 10 51 01
>30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 02 00 00
>
>00:1d.2 USB Controller: Intel Corp. 82801EB USB (Hub #3) (rev 02) (prog-if
>00 [UHCI])
> Subsystem: Dell Computer Corporation: Unknown device 0151
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
>Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr-
>DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin C routed to IRQ 9
> Region 4: I/O ports at ff40 [size=32]
>00: 86 80 d7 24 05 00 80 02 02 00 03 0c 00 00 00 00
>10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>20: 41 ff 00 00 00 00 00 00 00 00 00 00 28 10 51 01
>30: 00 00 00 00 00 00 00 00 00 00 00 00 09 03 00 00
>
>00:1d.3 USB Controller: Intel Corp. 82801EB USB EHCI Controller #2 (rev 02)
>(prog-if 00 [UHCI])
> Subsystem: Dell Computer Corporation: Unknown device 0151
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
>Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr-
>DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin A routed to IRQ 11
> Region 4: I/O ports at ff20 [size=32]
>00: 86 80 de 24 05 00 80 02 02 00 03 0c 00 00 00 00
>10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>20: 21 ff 00 00 00 00 00 00 00 00 00 00 28 10 51 01
>30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 00 00
>
>00:1d.7 USB Controller: Intel Corp. 82801EB USB EHCI Controller (rev 02)
>(prog-if 20 [EHCI])
> Subsystem: Dell Computer Corporation: Unknown device 0151
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
>Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr-
>DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin D routed to IRQ 5
> Region 0: Memory at ffa80800 (32-bit, non-prefetchable) [size=1K]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
>PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] #0a [20a0]
>00: 86 80 dd 24 06 01 90 02 02 20 03 0c 00 00 00 00
>10: 00 08 a8 ff 00 00 00 00 00 00 00 00 00 00 00 00
>20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 51 01
>30: 00 00 00 00 50 00 00 00 00 00 00 00 05 04 00 00
>
>00:1e.0 PCI bridge: Intel Corp. 82801BA/CA/DB PCI Bridge (rev c2) (prog-if
>00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
>Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr-
>DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
> I/O behind bridge: 0000d000-0000dfff
> Memory behind bridge: fcf00000-fcffffff
> BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
>00: 86 80 4e 24 07 01 80 00 c2 00 04 06 00 00 01 00
>10: 00 00 00 00 00 00 00 00 00 02 02 20 d0 d0 80 22
>20: f0 fc f0 fc f0 ff 00 00 00 00 00 00 00 00 00 00
>30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 02 00
>
>
>00:1f.0 ISA bridge: Intel Corp. 82801EB ISA Bridge (LPC) (rev 02)
> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
>Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr-
>DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
>00: 86 80 d0 24 0f 01 80 02 02 00 01 06 00 00 80 00
>10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
>00:1f.1 IDE interface: Intel Corp. 82801EB ICH5 IDE (rev 02) (prog-if 8a
>[Master SecP PriP])
> Subsystem: Dell Computer Corporation: Unknown device 0151
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
>Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr-
>DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin A routed to IRQ 9
> Region 0: I/O ports at 01f0 [size=8]
> Region 1: I/O ports at 03f4
> Region 2: I/O ports at 0170 [size=8]
> Region 3: I/O ports at 0374
> Region 4: I/O ports at ffa0 [size=16]
> Region 5: Memory at febffc00 (32-bit, non-prefetchable) [size=1K]
>00: 86 80 db 24 07 00 88 02 02 8a 01 01 00 00 00 00
>10: f1 01 00 00 f5 03 00 00 71 01 00 00 75 03 00 00
>20: a1 ff 00 00 00 fc bf fe 00 00 00 00 28 10 51 01
>30: 00 00 00 00 00 00 00 00 00 00 00 00 09 01 00 00
>
>00:1f.2 IDE interface: Intel Corp.: Unknown device 24d1 (rev 02) (prog-if
>8f [Master SecP SecO PriP
>PriO])
> Subsystem: Dell Computer Corporation: Unknown device 0151
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
>Stepping- SERR- FastB2B- Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr-
>DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin A routed to IRQ 9
> Region 0: I/O ports at fe00 [size=8]
> Region 1: I/O ports at fe10 [size=4]
> Region 2: I/O ports at fe20 [size=8]
> Region 3: I/O ports at fe30 [size=4]
> Region 4: I/O ports at fea0 [size=16]
>00: 86 80 d1 24 05 00 a0 02 02 8f 01 01 00 00 00 00
>10: 01 fe 00 00 11 fe 00 00 21 fe 00 00 31 fe 00 00
>20: a1 fe 00 00 00 00 00 00 00 00 00 00 28 10 51 01
>30: 00 00 00 00 00 00 00 00 00 00 00 00 09 01 00 00
>
>00:1f.3 SMBus: Intel Corp. 82801EB SMBus (rev 02)
> Subsystem: Dell Computer Corporation: Unknown device 0151
> Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
>Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr-
>DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Interrupt: pin B routed to IRQ 3
> Region 4: I/O ports at eda0 [size=32]
>00: 86 80 d3 24 01 00 80 02 02 00 05 0c 00 00 00 00
>10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>20: a1 ed 00 00 00 00 00 00 00 00 00 00 28 10 51 01
>30: 00 00 00 00 00 00 00 00 00 00 00 00 03 02 00 00
>
>00:1f.5 Multimedia audio controller: Intel Corp. 82801EB AC'97 Audio (rev
>02)
> Subsystem: Dell Computer Corporation: Unknown device 0151
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
>Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr-
>DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin B routed to IRQ 3
> Region 0: I/O ports at ee00 [size=256]
> Region 1: I/O ports at edc0 [size=64]
> Region 2: Memory at febffa00 (32-bit, non-prefetchable) [size=512]
> Region 3: Memory at febff900 (32-bit, non-prefetchable) [size=256]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
>PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>00: 86 80 d5 24 07 00 90 02 02 00 01 04 00 00 00 00
>10: 01 ee 00 00 c1 ed 00 00 00 fa bf fe 00 f9 bf fe
>20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 51 01
>30: 00 00 00 00 50 00 00 00 00 00 00 00 03 02 00 00
>
>01:00.0 VGA compatible controller: nVidia Corporation NV18 [GeForce4 MX 440
>AGP 8x] (rev a2) (prog-if 00 [VGA])
> Subsystem: nVidia Corporation: Unknown device 0191
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
>Stepping- SERR- FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr-
>DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64 (1250ns min, 250ns max)
> Interrupt: pin A routed to IRQ 11
> Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
> Region 1: Memory at f0000000 (32-bit, prefetchable) [size=128M]
> Expansion ROM at fea00000 [disabled] [size=128K]
> Capabilities: [60] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
>PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [44] AGP version 3.0
> Status: RQ=31 SBA+ 64bit- FW+ Rate=x1,x2
> Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
>00: de 10 81 01 07 00 b0 02 a2 00 00 03 00 40 00 00
>10: 00 00 00 fd 08 00 00 f0 00 00 00 00 00 00 00 00
>20: 00 00 00 00 00 00 00 00 00 00 00 00 de 10 91 01
>30: 00 00 a0 fe 60 00 00 00 00 00 00 00 0b 01 05 01
>
>02:07.0 CardBus bridge: Ricoh Co Ltd RL5c475 (rev 80)
> Subsystem: CARRY Computer ENG. CO Ltd: Unknown device 0101
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
>Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr-
>DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 168
> Interrupt: pin A routed to IRQ 0
> Region 0: Memory at 20000000 (32-bit, non-prefetchable) [size=4K]
> Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
> Memory window 0: 20400000-207ff000 (prefetchable)
> Memory window 1: 20800000-20bff000
> I/O window 0: 00004000-000040ff
> I/O window 1: 00004400-000044ff
> BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt-
>PostWrite+
> 16-bit legacy interface ports at 0001
>00: 80 11 75 04 07 00 10 02 80 00 07 06 00 a8 02 00
>10: 00 00 00 20 dc 00 00 02 02 03 06 b0 00 00 40 20
>20: 00 f0 7f 20 00 00 80 20 00 f0 bf 20 00 40 00 00
>30: fc 40 00 00 00 44 00 00 fc 44 00 00 00 01 00 05
>40: ef 14 01 01 01 00 00 00 00 00 00 00 00 00 00 00
>50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
>02:0c.0 Ethernet controller: Intel Corp. 82540EM Gigabit Ethernet
>Controller (rev 02)
> Subsystem: Dell Computer Corporation: Unknown device 0151
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
>Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr-
>DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64 (63750ns min), cache line size 10
> Interrupt: pin A routed to IRQ 9
> Region 0: Memory at fcfe0000 (32-bit, non-prefetchable) [size=128K]
> Region 2: I/O ports at df40 [size=64]
> Capabilities: [dc] Power Management version 2
> Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
>PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=1 PME-
> Capabilities: [e4] PCI-X non-bridge device.
> Command: DPERE- ERO+ RBC=0 OST=0
> Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-,
>DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM- Capabilities: [f0] Message
>Signalled Interrupts: 64bit+ Queue=0/0 Enable-
> Address: 0000000000000000 Data: 0000
>00: 86 80 0e 10 17 01 30 02 02 00 00 02 10 40 00 00
>10: 00 00 fe fc 00 00 00 00 41 df 00 00 00 00 00 00
>20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 51 01
>30: 00 00 00 00 dc 00 00 00 00 00 00 00 09 01 ff 00
>
>
>I will really appreciate some clue , please point me the right direction.
>
>Well FYI , this is what i get when i *compile* the kernel which i working
>on, and do "modules_install"
>
>mkdir -p pcmcia; \
>find kernel -path '*/pcmcia/*' -name '*.o' | xargs -i -r ln -sf ../{}
>pcmcia
>if [ -r System.map ]; then /sbin/depmod -ae -F System.map 2.4.20rn; fi
>depmod: *** Unresolved symbols in /lib/modules/2.4.20rn/pcmcia/tcic.o
>depmod: pci_irq_mask
>[root at localhost linux-2.4.20]#
>===============================
>
>Well i believe it won't be that significant, i am curious if it is.
>
>Meanwhile, Also i download the 'isapnptools-2.6" and tried to configure
>which configure the Plug and Play devices, i am still working on it to see
>how to works!
>
>
>Looking for some quick response,
>
>Thanx--Gaurav
>
>Thanx
>
>_________________________________________________________________
>Discover the best of the best at MSN Luxury Living. http://lexus.msn.com/
>
>_______________________________________________
>HostAP mailing list
>HostAP at shmoo.com
>http://lists.shmoo.com/mailman/listinfo/hostap
_________________________________________________________________
Planning a family vacation? Check out the MSN Family Travel guide!
http://dollar.msn.com
More information about the Hostap
mailing list