(new info) Problems with wpa_supplicant and Linksys WPC54G + WPA EAP-TTLS
Dan Parsons
dparsons
Mon Dec 20 13:19:39 PST 2004
While I'm waiting for the ndiswrapper folk to get back to me, I decided
to get LinuxAnt's DriverLoader a try instead of ndiswrapper. So far I
haven't had any system crashes, which is great. However WPA+EAP-TTLS
still isn't working. Below is some debugging information for you...
does it look like the same issue as what I'm having with ndiswrapper?
I'm using the same Windows drivers with it as I was with ndiswrapper
and also the same card.
I thank you in advance for any information you can give me.
First, my wpa_supplicant (0.3.2) .config:
CONFIG_IEEE8021X_EAPOL=y
CONFIG_EAP_TLS=y
CONFIG_EAP_TTLS=y
CONFIG_EAP_PSK=y
CONFIG_WIRELESS_EXTENSION=y
CONFIG_DRIVER_HOSTAP=y
My wpa_supplicant command:
wpa_supplicant -dd -i eth1 -c /etc/wpa_supplicant.conf
My wpa_supplicant.conf file:
#ctrl_interface=/var/run/wpa_supplicant
#ctrl_interface_group=0
ap_scan=1
network={
ssid="SDPRA"
proto=WPA
key_mgmt=WPA-EAP
auth_alg=OPEN
pairwise=TKIP
group=TKIP
eap=TTLS
identity="someusern"
anonymous_identity="foo"
password="somepassword"
phase2="autheap=PAP autheap=MD5"
}
dmesg output while wpa_supplicant is running:
eth1: prism2_param: unknown param 15
eth1: prism2_param: unknown param 23
eth1: New link status: Connected (0001)
eth1 (WE) : Wireless Event too big (331)
eth1: New link status: Disconnected (0002)
eth1: prism2_param: unknown param 15
eth1: prism2_param: unknown param 23
eth1: New link status: Connected (0001)
eth1 (WE) : Wireless Event too big (331)
eth1: New link status: Disconnected (0002)
eth1: prism2_param: unknown param 15
eth1: prism2_param: unknown param 23
eth1: New link status: Connected (0001)
eth1 (WE) : Wireless Event too big (331)
eth1: New link status: Disconnected (0002)
eth1: prism2_param: unknown param 15
eth1: prism2_param: unknown param 23
eth1: New link status: Connected (0001)
eth1 (WE) : Wireless Event too big (331)
eth1: New link status: Disconnected (0002)
Stderr output, while wpa_supplicant is running:
l2_packet_receive - recv: Network is down
ioctl[PRISM2_IOCTL_PRISM2_PARAM]: Operation not supported
ioctl[PRISM2_IOCTL_PRISM2_PARAM]: Operation not supported
l2_packet_send - send: Network is down
ioctl[PRISM2_IOCTL_PRISM2_PARAM]: Operation not supported
ioctl[PRISM2_IOCTL_PRISM2_PARAM]: Operation not supported
l2_packet_send - send: Network is down
ioctl[PRISM2_IOCTL_PRISM2_PARAM]: Operation not supported
ioctl[PRISM2_IOCTL_PRISM2_PARAM]: Operation not supported
l2_packet_send - send: Network is down
ioctl[PRISM2_IOCTL_PRISM2_PARAM]: Operation not supported
ioctl[PRISM2_IOCTL_PRISM2_PARAM]: Operation not supported
l2_packet_send - send: Network is down
And now the actual wpa_supplicant output:
Initializing interface 'eth1' conf '/etc/wpa_supplicant.conf' driver
'default'
Configuration file '/etc/wpa_supplicant.conf' ->
'/etc/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant.conf'
ap_scan=1
Line: 5 - start of a new network block
ssid - hexdump_ascii(len=5):
53 44 50 52 41 SDPRA
proto: 0x1
key_mgmt: 0x1
auth_alg: 0x1
pairwise: 0x8
group: 0x8
eap methods - hexdump(len=2): 15 00
identity - hexdump_ascii(len=7):
70 72 61 75 73 65 72 prauser
anonymous_identity - hexdump_ascii(len=3):
66 6f 6f foo
password - hexdump_ascii(len=6): [REMOVED]
phase2 - hexdump_ascii(len=23):
61 75 74 68 65 61 70 3d 50 41 50 20 61 75 74 68 autheap=PAP auth
65 61 70 3d 4d 44 35 eap=MD5
Priority group 0
id=0 ssid='SDPRA'
Initializing interface (2) 'eth1'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
Own MAC address: 00:0c:41:2c:25:5d
wpa_driver_hostap_set_wpa: enabled=1
wpa_driver_hostap_set_key: alg=none key_idx=0 set_tx=0 seq_len=0
key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=1 set_tx=0 seq_len=0
key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=2 set_tx=0 seq_len=0
key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=3 set_tx=0 seq_len=0
key_len=0
wpa_driver_hostap_set_countermeasures: enabled=0
wpa_driver_hostap_set_drop_unencrypted: enabled=1
Setting scan request: 0 sec 100000 usec
Starting AP scan (broadcast SSID)
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0
idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0
idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0
idleWhile=0
Wireless event: cmd=0x8b19 len=12
Received 827 bytes of scan results (3 BSSes)
Scan results: 3
Selecting BSS from priority group 0
0: 00:0c:41:ad:05:fb ssid='NICE_TRY_WARDRIVER' wpa_ie_len=24
rsn_ie_len=0
skip - SSID mismatch
1: 00:12:7f:47:f4:a0 ssid='SDPRA' wpa_ie_len=24 rsn_ie_len=0
selected
Trying to associate with 00:12:7f:47:f4:a0 (SSID='SDPRA' freq=2452 MHz)
Cancelling scan request
Automatic auth_alg selection: 0x1
Overriding auth_alg selection: 0x1
WPA: using IEEE 802.11i/D3.0
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 1
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT 802.1X
WPA: Own WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02
01 00 00 50 f2 02 01 00 00 50 f2 01
No keys have been configured - skip key clearing
wpa_driver_hostap_set_drop_unencrypted: enabled=1
wpa_driver_hostap_associate
hostap: Failed to configure ieee_802_1x param
Setting authentication timeout: 5 sec 0 usec
EAPOL: External notification - portControl=Auto
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:12:7f:47:f4:a0
Association event - clear replay counter
Associated to a new BSS: BSSID=00:12:7f:47:f4:a0
No keys have been configured - skip key clearing
Associated with 00:12:7f:47:f4:a0
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - portEnabled=1
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: txStart
TX EAPOL - hexdump(len=18): 00 12 7f 47 f4 a0 00 0c 41 2c 25 5d 88 8e
01 01 00 00
EAPOL: SUPP_BE entering state IDLE
EAP: EAP entering state INITIALIZE
EAP: EAP entering state IDLE
Setting authentication timeout: 10 sec 0 usec
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=29
idleWhile=59
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=28
idleWhile=58
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=27
idleWhile=57
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=26
idleWhile=56
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=25
idleWhile=55
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=24
idleWhile=54
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=23
idleWhile=53
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=22
idleWhile=52
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=21
idleWhile=51
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=20
idleWhile=50
Authentication with 00:12:7f:47:f4:a0 timed out.
wpa_driver_hostap_disassociate
wpa_driver_hostap_reset: type=2
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portValid=0
Setting scan request: 0 sec 0 usec
Starting AP scan (broadcast SSID)
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:00:00:00:00:00
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
Disconnect event - remove keys
wpa_driver_hostap_set_key: alg=none key_idx=0 set_tx=0 seq_len=0
key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=1 set_tx=0 seq_len=0
key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=2 set_tx=0 seq_len=0
key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=3 set_tx=0 seq_len=0
key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=0 set_tx=0 seq_len=0
key_len=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=19
idleWhile=49
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=18
idleWhile=48
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=17
idleWhile=47
Wireless event: cmd=0x8b19 len=12
Received 1032 bytes of scan results (4 BSSes)
Scan results: 4
Selecting BSS from priority group 0
0: 00:0c:41:ad:05:fb ssid='NICE_TRY_WARDRIVER' wpa_ie_len=24
rsn_ie_len=0
skip - SSID mismatch
1: 00:12:7f:47:f4:a0 ssid='SDPRA' wpa_ie_len=24 rsn_ie_len=0
selected
Trying to associate with 00:12:7f:47:f4:a0 (SSID='SDPRA' freq=2452 MHz)
Cancelling scan request
Automatic auth_alg selection: 0x1
Overriding auth_alg selection: 0x1
WPA: using IEEE 802.11i/D3.0
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 1
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT 802.1X
WPA: Own WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02
01 00 00 50 f2 02 01 00 00 50 f2 01
No keys have been configured - skip key clearing
wpa_driver_hostap_set_drop_unencrypted: enabled=1
wpa_driver_hostap_associate
hostap: Failed to configure ieee_802_1x param
Setting authentication timeout: 5 sec 0 usec
EAPOL: External notification - portControl=Auto
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=16
idleWhile=46
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:12:7f:47:f4:a0
Association event - clear replay counter
Associated to a new BSS: BSSID=00:12:7f:47:f4:a0
No keys have been configured - skip key clearing
Associated with 00:12:7f:47:f4:a0
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - portEnabled=1
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: txStart
TX EAPOL - hexdump(len=18): 00 12 7f 47 f4 a0 00 0c 41 2c 25 5d 88 8e
01 01 00 00
EAPOL: SUPP_BE entering state IDLE
EAP: EAP entering state INITIALIZE
EAP: EAP entering state IDLE
Setting authentication timeout: 10 sec 0 usec
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=29
idleWhile=59
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=28
idleWhile=58
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=27
idleWhile=57
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=26
idleWhile=56
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=25
idleWhile=55
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=24
idleWhile=54
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=23
idleWhile=53
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=22
idleWhile=52
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=21
idleWhile=51
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=20
idleWhile=50
Authentication with 00:12:7f:47:f4:a0 timed out.
wpa_driver_hostap_disassociate
wpa_driver_hostap_reset: type=2
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portValid=0
Setting scan request: 0 sec 0 usec
Starting AP scan (broadcast SSID)
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:00:00:00:00:00
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
Disconnect event - remove keys
wpa_driver_hostap_set_key: alg=none key_idx=0 set_tx=0 seq_len=0
key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=1 set_tx=0 seq_len=0
key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=2 set_tx=0 seq_len=0
key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=3 set_tx=0 seq_len=0
key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=0 set_tx=0 seq_len=0
key_len=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=19
idleWhile=49
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=18
idleWhile=48
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=17
idleWhile=47
Wireless event: cmd=0x8b19 len=12
Received 827 bytes of scan results (3 BSSes)
Scan results: 3
Selecting BSS from priority group 0
0: 00:0c:41:ad:05:fb ssid='NICE_TRY_WARDRIVER' wpa_ie_len=24
rsn_ie_len=0
skip - SSID mismatch
1: 00:12:7f:47:f4:a0 ssid='SDPRA' wpa_ie_len=24 rsn_ie_len=0
selected
Trying to associate with 00:12:7f:47:f4:a0 (SSID='SDPRA' freq=2452 MHz)
Cancelling scan request
Automatic auth_alg selection: 0x1
Overriding auth_alg selection: 0x1
WPA: using IEEE 802.11i/D3.0
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 1
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT 802.1X
WPA: Own WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02
01 00 00 50 f2 02 01 00 00 50 f2 01
No keys have been configured - skip key clearing
wpa_driver_hostap_set_drop_unencrypted: enabled=1
wpa_driver_hostap_associate
hostap: Failed to configure ieee_802_1x param
Setting authentication timeout: 5 sec 0 usec
EAPOL: External notification - portControl=Auto
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:12:7f:47:f4:a0
Association event - clear replay counter
Associated to a new BSS: BSSID=00:12:7f:47:f4:a0
No keys have been configured - skip key clearing
Associated with 00:12:7f:47:f4:a0
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - portEnabled=1
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: txStart
TX EAPOL - hexdump(len=18): 00 12 7f 47 f4 a0 00 0c 41 2c 25 5d 88 8e
01 01 00 00
EAPOL: SUPP_BE entering state IDLE
EAP: EAP entering state INITIALIZE
EAP: EAP entering state IDLE
Setting authentication timeout: 10 sec 0 usec
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=29
idleWhile=59
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=28
idleWhile=58
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=27
idleWhile=57
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=26
idleWhile=56
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=25
idleWhile=55
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=24
idleWhile=54
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=23
idleWhile=53
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=22
idleWhile=52
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=21
idleWhile=51
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=20
idleWhile=50
Authentication with 00:12:7f:47:f4:a0 timed out.
wpa_driver_hostap_disassociate
wpa_driver_hostap_reset: type=2
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portValid=0
Setting scan request: 0 sec 0 usec
Starting AP scan (broadcast SSID)
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:00:00:00:00:00
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
Disconnect event - remove keys
wpa_driver_hostap_set_key: alg=none key_idx=0 set_tx=0 seq_len=0
key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=1 set_tx=0 seq_len=0
key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=2 set_tx=0 seq_len=0
key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=3 set_tx=0 seq_len=0
key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=0 set_tx=0 seq_len=0
key_len=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=19
idleWhile=49
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=18
idleWhile=48
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=17
idleWhile=47
Wireless event: cmd=0x8b19 len=12
Received 827 bytes of scan results (3 BSSes)
Scan results: 3
Selecting BSS from priority group 0
0: 00:0c:41:ad:05:fb ssid='NICE_TRY_WARDRIVER' wpa_ie_len=24
rsn_ie_len=0
skip - SSID mismatch
1: 00:12:7f:47:f4:a0 ssid='SDPRA' wpa_ie_len=24 rsn_ie_len=0
selected
Trying to associate with 00:12:7f:47:f4:a0 (SSID='SDPRA' freq=2452 MHz)
Cancelling scan request
Automatic auth_alg selection: 0x1
Overriding auth_alg selection: 0x1
WPA: using IEEE 802.11i/D3.0
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 1
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT 802.1X
WPA: Own WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02
01 00 00 50 f2 02 01 00 00 50 f2 01
No keys have been configured - skip key clearing
wpa_driver_hostap_set_drop_unencrypted: enabled=1
wpa_driver_hostap_associate
hostap: Failed to configure ieee_802_1x param
Setting authentication timeout: 5 sec 0 usec
EAPOL: External notification - portControl=Auto
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=16
idleWhile=46
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:12:7f:47:f4:a0
Association event - clear replay counter
Associated to a new BSS: BSSID=00:12:7f:47:f4:a0
No keys have been configured - skip key clearing
Associated with 00:12:7f:47:f4:a0
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
EAPOL: External notification - portEnabled=1
EAPOL: SUPP_PAE entering state CONNECTING
EAPOL: txStart
TX EAPOL - hexdump(len=18): 00 12 7f 47 f4 a0 00 0c 41 2c 25 5d 88 8e
01 01 00 00
EAPOL: SUPP_BE entering state IDLE
EAP: EAP entering state INITIALIZE
EAP: EAP entering state IDLE
Setting authentication timeout: 10 sec 0 usec
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=29
idleWhile=59
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=28
idleWhile=58
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=27
idleWhile=57
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=26
idleWhile=56
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=25
idleWhile=55
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=24
idleWhile=54
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=23
idleWhile=53
Signal 2 received - terminating
wpa_driver_hostap_deauthenticate
wpa_driver_hostap_reset: type=2
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portValid=0
wpa_driver_hostap_set_wpa: enabled=0
wpa_driver_hostap_set_drop_unencrypted: enabled=0
wpa_driver_hostap_set_countermeasures: enabled=0
Dan Parsons
Systems Administrator
Pioneer Research Center USA, Inc.
On Dec 17, 2004, at 9:34 PM, Dan Parsons wrote:
> Thank you very much for the information. I will show it to the
> ndiswrapper people.
>
> Dan Parsons
> Systems Administrator
> Pioneer Research Center USA, Inc.
>
> On Dec 17, 2004, at 8:59 PM, Jouni Malinen wrote:
>
>> On Fri, Dec 17, 2004 at 07:17:40PM -0800, Dan Parsons wrote:
>>
>>> I have tested both APs in WPA-PSK mode and EAP-TTLS mode. I
>>> understand
>>> that it may be a problem with ndiswrapper; I have written to their
>>> mailing list as well. Below is a log of a successful WPA-PSK session
>>> with the same driver/card:
>>
>>> Trying to associate with 00:0c:41:ad:05:fb (SSID='NICE_TRY_WARDRIVER'
>>> freq=2462 MHz)
>>
>>> Wireless event: cmd=0x8c02 len=235
>>> Custom wireless event:
>>> 'ASSOCINFO(ReqIEs=00124e4943455f5452595f574152445249564552010882848b9
>>> 6a4
>>> b0c8ec32048c9298e0dd06004096010100dd050010180100dd160050f20101000050f
>>> 202
>>> 01000050f20201000050f202
>>> RespIEs=010882848b96a4b0c8ec32048c9298e0dd050010180100)'
>>> Association info event
>>
>> This is the event that was missing from the WPA EAP-TTLS case. I have
>> no
>> idea it would be only missing from WPA EAP. I would have understood
>> completely failed association since NDIS drivers use different
>> auth_mode
>> configuration for these. However, both cases were generating
>> association
>> event. In other words, yes, this is more on the ndiswrapper side..
>> Either ndiswrapper does not know how to read/parse the assoc info in
>> WPA
>> EAP case or the NDIS driver you are using is doing something odd.
>>
>> --
>> Jouni Malinen PGP id
>> EFC895FA
>> _______________________________________________
>> HostAP mailing list
>> HostAP at shmoo.com
>> http://lists.shmoo.com/mailman/listinfo/hostap
>
> _______________________________________________
> HostAP mailing list
> HostAP at shmoo.com
> http://lists.shmoo.com/mailman/listinfo/hostap
More information about the Hostap
mailing list