problem after installing hostap! Please help!!
ken
ee_cskaa
Wed Aug 25 05:01:10 PDT 2004
I use NL 2511-CD PLUS EXT2 and Redhat 9 to build hostap
eth0 - Intel ethernet card
eth1 - Intel pro/2100 wireless card (use ipw2100 driver)
wlan0 - NL2511-CD PLUS EXT2 (use hostap driver)
After installing hostap, I have some problems related to network
interface.
When I enable eth0 and eth1 interface, I cannot ping to outside through
eth0, but eth1 can.
When I enable eth0 and disable eth1, I can ping to anywhere through
eth0, but when I use web browser, I cannot go to internet
How to fix it? I want to use both interface to ping outside and go to
internet.
Below is my config:
[root at localhost ken]# ifconfig
eth0 Link encap:Ethernet HWaddr 00:09:6B:BF:E3:D1
inet addr:192.168.1.102 Bcast:192.168.1.255
Mask:255.255.255.0
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Base address:0x8000 Memory:c0220000-c0240000
eth1 Link encap:Ethernet HWaddr 00:04:23:68:7B:DB
inet addr:192.168.1.103 Bcast:192.168.1.255
Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:2989 errors:0 dropped:0 overruns:0 frame:0
TX packets:2819 errors:0 dropped:0 overruns:0 carrier:1
collisions:0 txqueuelen:1000
RX bytes:3071611 (2.9 Mb) TX bytes:345546 (337.4 Kb)
Interrupt:11 Base address:0x7000 Memory:c0210000-c0210fff
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:7943 errors:0 dropped:0 overruns:0 frame:0
TX packets:7943 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:542104 (529.3 Kb) TX bytes:542104 (529.3 Kb)
wifi0 Link encap:UNSPEC HWaddr
00-02-6F-01-73-BC-00-00-00-00-00-00-00-00-00-00
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:240 (240.0 b)
Interrupt:3 Base address:0x100
wlan0 Link encap:Ethernet HWaddr 00:02:6F:01:73:BC
inet addr:10.1.2.1 Bcast:10.1.2.255 Mask:255.255.255.0
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:240 (240.0 b)
Interrupt:3 Base address:0x100
[root at localhost ken]# iwconfig
lo no wireless extensions.
dummy0 no wireless extensions.
eth0 no wireless extensions.
Warning: Driver for device eth1 has been compiled with version 16
of Wireless Extension, while this program is using version 15.
Some things may be broken...
eth1 IEEE 802.11b ESSID:"linksys.wireless.org" Nickname:"ipw2100"
Mode:Managed Channel:11 Access Point: 00:0F:66:A8:17:90
Bit Rate=11Mb/s Tx-Power=32 dBm
Retry:on RTS thr=2304 B Fragment thr:off
Encryption key:off
Power Management:off
Link Quality:100/0 Signal level:-20 dBm Noise level:-98 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
wifi0 IEEE 802.11b ESSID:"skchung.wireless.org"
Nickname:"localhost.localdomain"
Mode:Master Frequency:2.412GHz Access Point:
00:02:6F:01:73:BC
Bit Rate=11Mb/s Sensitivity=1/0
Retry min limit:8 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:6 Missed beacon:0
wlan0 IEEE 802.11b ESSID:"skchung.wireless.org"
Nickname:"localhost.localdomain"
Mode:Master Frequency:2.412GHz Access Point:
00:02:6F:01:73:BC
Bit Rate=11Mb/s Sensitivity=1/0
Retry min limit:8 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:6 Missed beacon:0
More information about the Hostap
mailing list