Severe problem during download of Firmware makes PCI card useless
Ingo Hoffmann
ingo
Sun Nov 2 13:39:58 PST 2003
I tried to upgrade the firmware of my Prism V2.5 PCI based card (Allnet
191), because the firmware on the card seemed to be rather old. (V 1.3.5).
I tried to follow the instruction in Jun Sun's mini howto.
(http://linux.junsun.net/intersil-prism/) very closely.
After having tried the dry run as suggested (Even if I didn't understand
every message of this dry run I saw the OK at the very end, so I thought
it was OK.) I ran the real command as you can see from the log and kept
fingers crossed a suggested. Unfortunately after having started smoothly
the download aborted as can be seen from the attached logs!
This was the worst case because afterwards the card was useless. It was
not possible to load the driver under Linux and a tried even under W2k
and failed as well. So now I have the situation, that I need help to
reflash the card, because I can't use it anymore!
Can somebody help? I would also be interested whether there is a place
where I could send the card to get it reflashed. Diffferent suggetions?
Every hint would be greatly appreciated!
Regards Ingo
# /tmp/hostap-utils-0.1.0/prism2_srec -v wlan0
/tmp/Intersil/1.7.4/pk010101.hex
/home/imh/TXT/Firmware/WLAN/Intersil/1.7.4/rf010704.hex
S3 CRC-16 generation record: start=0x007E17FE len=2 prog=0
Start address 0x00000000
srec summary for pk010101.hex
Component: 0x0015 1.1.1 (primary firmware)
Supported platforms:
0x800c 1.0.0, 0x8013 1.0.0, 0x8017 1.0.0, 0x801b 1.0.0, 0x8022 1.0.0
Interface compatibility information:
role=Supplier variant=1 range=4-4 iface=Primary Firmware-Driver (3)
role=Actor variant=2 range=1-1 iface=Controller-Firmware (2)
Separate S3 data areas:
S3 area count: 3
addr=0x007E0000..0x007E0B55 (len=2902)
addr=0x007E0C00..0x007E151F (len=2336)
addr=0x007E17FE..0x007E17FF (len=2)
Total data length: 5240
Start address 0x00000000
Special S3 firmware info record - name 'RF010704.HEX'
Start address 0x003f0c01
S3 CRC-16 generation record: start=0x007E1800 len=65414 prog=1
srec summary for rf010704.hex
Included file name: RF010704.HEX
Component: 0x001f 1.7.4 (station firmware)
Supported platforms:
0x800a 1.0.0, 0x800b 1.0.0, 0x800c 1.0.0, 0x800d 1.0.0, 0x8012 1.0.0
0x8013 1.0.0, 0x8014 1.0.0, 0x8016 1.0.0, 0x8017 1.0.0, 0x8018 1.0.0
0x801a 1.0.0, 0x801b 1.0.0, 0x801c 1.0.0, 0x8021 1.0.0, 0x8022 1.0.0
0x8023 1.0.0, 0x800a 1.0.0, 0x800e 1.0.0, 0x8015 1.0.0, 0x8019 1.0.0
0x801d 1.0.0, 0x8024 1.0.0
Interface compatibility information:
role=Supplier variant=4 range=1-12 iface=Station Firmware-Driver (4)
role=Actor variant=1 range=1-1 iface=Modem-Firmware (1)
role=Actor variant=2 range=1-1 iface=Controller-Firmware (2)
role=Actor variant=1 range=4-4 iface=Primary Firmware-Driver (3)
Separate S3 data areas:
S3 area count: 3
addr=0x007E1800..0x007EE28D (len=51854)
addr=0x007F0800..0x007F1785 (len=3974)
addr=0x007FE000..0x007FECC5 (len=3270)
Total data length: 59098
Start address 0x003f0c01
Wireless LAN card information:
Components:
NICID: 0x8013 v1.0.0
PRIID: 0x0015 v1.0.5
STAID: 0x001f v1.3.4
Interface compatibility information:
PRI role=Supplier variant=1 range=1-1 iface=Modem-Firmware (1)
PRI role=Supplier variant=2 range=1-1 iface=Controller-Firmware (2)
PRI role=Supplier variant=1 range=1-3 iface=Primary Firmware-Driver (3)
STA role=Supplier variant=1 range=1-9 iface=Station Firmware-Driver (4)
PRI role=Actor variant=2 range=1-1 iface=Controller-Firmware (2)
STA role=Actor variant=2 range=1-1 iface=Controller-Firmware (2)
STA role=Actor variant=1 range=1-1 iface=Modem-Firmware (1)
Verifying update compatibility and combining data:
Plugging PDR 0xffffffff at 0x007e1510 (len=14)
Plugging PDR 0x0003 at 0x007e14b8 (len=12)
Plugging PDR 0x0005 at 0x007e1310 (len=2)
PDR 0x0005 not found from wlan card PDA. Using default data.
len=2: 00 01
Plugging PDR 0x0006 at 0x007e14f0 (len=10)
Plugging PDR 0x0007 at 0x007e1504 (len=10)
Plugging PDR 0x0008 at 0x007e14c4 (len=8)
Plugging PDR 0x0400 at 0x007e1314 (len=2)
Plugging PDR 0x0402 at 0x007e131e (len=4)
Plugging PDR 0x0403 at 0x007e1316 (len=16)
Plugging PDR 0x0404 at 0x007e1326 (len=10)
Plugging PDR 0x0408 at 0x007e1312 (len=2)
PDR 0x0408 not found from wlan card PDA. Using default data.
len=2: 64 00
Plugging PDR 0x0001 at 0x007e14cc (len=16)
Plug record length mismatch (PDR=0x0001): 12 != 16
==> extend from default
PRI: old iface 1:1-3 new iface 1:4-4
Plugging PDR 0x0202 at 0x007f11ee (len=100)
Plugging PDR 0x0203 at 0x007f1252 (len=128)
Plugging PDR 0x0204 at 0x007f13d2 (len=80)
Plugging PDR 0x0405 at 0x007f1422 (len=4)
PDR 0x0405 not found from wlan card PDA. Using default data.
len=4: 00 00 00 30
Plugging PDR 0x0300 at 0x007f1426 (len=28)
Plugging PDR 0x0301 at 0x007f1442 (len=34)
Plugging PDR 0x0101 at 0x007f163a (len=6)
Plugging PDR 0x0103 at 0x007edd74 (len=12)
Plugging PDR 0x0104 at 0x007edeaa (len=2)
Plugging PDR 0x0105 at 0x007f1646 (len=2)
Plugging PDR 0x0105 at 0x007edee0 (len=2)
Plugging PDR 0x0105 at 0x007f1742 (len=2)
Plugging PDR 0x0107 at 0x007edd82 (len=2)
Plugging PDR 0x0006 at 0x007edd4e (len=10)
Plugging PDR 0x0406 at 0x007f16da (len=2)
PDR 0x0406 not found from wlan card PDA. Using default data.
len=2: 64 00
Plugging PDR 0x0302 at 0x007f146a (len=2)
PDR 0x0302 not found from wlan card PDA. Using default data.
len=2: 12 00
Plugging PDR 0x0303 at 0x007f146c (len=2)
PDR 0x0303 not found from wlan card PDA. Using default data.
len=2: ff 1f
Plugging PDR 0x0412 at 0x007edf02 (len=6)
PDR 0x0412 not found from wlan card PDA. Using default data.
len=6: ff ff 02 00 02 00
Generating CRC-16 (start=0x007e1800, len=65414) at 0x007e17fe
Allowing S3 overlap due to CRC-16 signature at 0x007e17fe (was: ffff)
After srec file merge
S3 area count: 5
addr=0x007E0000..0x007E0B55 (len=2902)
addr=0x007E0C00..0x007E151F (len=2336)
addr=0x007E17FE..0x007EE28D (len=51856)
addr=0x007F0800..0x007F1785 (len=3974)
addr=0x007FE000..0x007FECC5 (len=3270)
Total data length: 64338
OK.
# /tmp/hostap-utils-0.1.0/prism2_srec -v -f wlan0
/tmp/Intersil/1.7.4/pk010101.hex
/home/imh/TXT/Firmware/WLAN/Intersil/1.7.4/rf010704.hex
S3 CRC-16 generation record: start=0x007E17FE len=2 prog=0
Start address 0x00000000
srec summary for pk010101.hex
Component: 0x0015 1.1.1 (primary firmware)
Supported platforms:
0x800c 1.0.0, 0x8013 1.0.0, 0x8017 1.0.0, 0x801b 1.0.0, 0x8022 1.0.0
Interface compatibility information:
role=Supplier variant=1 range=4-4 iface=Primary Firmware-Driver (3)
role=Actor variant=2 range=1-1 iface=Controller-Firmware (2)
Separate S3 data areas:
S3 area count: 3
addr=0x007E0000..0x007E0B55 (len=2902)
addr=0x007E0C00..0x007E151F (len=2336)
addr=0x007E17FE..0x007E17FF (len=2)
Total data length: 5240
Start address 0x00000000
Special S3 firmware info record - name 'RF010704.HEX'
Start address 0x003f0c01
S3 CRC-16 generation record: start=0x007E1800 len=65414 prog=1
srec summary for rf010704.hex
Included file name: RF010704.HEX
Component: 0x001f 1.7.4 (station firmware)
Supported platforms:
0x800a 1.0.0, 0x800b 1.0.0, 0x800c 1.0.0, 0x800d 1.0.0, 0x8012 1.0.0
0x8013 1.0.0, 0x8014 1.0.0, 0x8016 1.0.0, 0x8017 1.0.0, 0x8018 1.0.0
0x801a 1.0.0, 0x801b 1.0.0, 0x801c 1.0.0, 0x8021 1.0.0, 0x8022 1.0.0
0x8023 1.0.0, 0x800a 1.0.0, 0x800e 1.0.0, 0x8015 1.0.0, 0x8019 1.0.0
0x801d 1.0.0, 0x8024 1.0.0
Interface compatibility information:
role=Supplier variant=4 range=1-12 iface=Station Firmware-Driver (4)
role=Actor variant=1 range=1-1 iface=Modem-Firmware (1)
role=Actor variant=2 range=1-1 iface=Controller-Firmware (2)
role=Actor variant=1 range=4-4 iface=Primary Firmware-Driver (3)
Separate S3 data areas:
S3 area count: 3
addr=0x007E1800..0x007EE28D (len=51854)
addr=0x007F0800..0x007F1785 (len=3974)
addr=0x007FE000..0x007FECC5 (len=3270)
Total data length: 59098
Start address 0x003f0c01
Wireless LAN card information:
Components:
NICID: 0x8013 v1.0.0
PRIID: 0x0015 v1.0.5
STAID: 0x001f v1.3.4
Interface compatibility information:
PRI role=Supplier variant=1 range=1-1 iface=Modem-Firmware (1)
PRI role=Supplier variant=2 range=1-1 iface=Controller-Firmware (2)
PRI role=Supplier variant=1 range=1-3 iface=Primary Firmware-Driver (3)
STA role=Supplier variant=1 range=1-9 iface=Station Firmware-Driver (4)
PRI role=Actor variant=2 range=1-1 iface=Controller-Firmware (2)
STA role=Actor variant=2 range=1-1 iface=Controller-Firmware (2)
STA role=Actor variant=1 range=1-1 iface=Modem-Firmware (1)
Verifying update compatibility and combining data:
Plugging PDR 0xffffffff at 0x007e1510 (len=14)
Plugging PDR 0x0003 at 0x007e14b8 (len=12)
Plugging PDR 0x0005 at 0x007e1310 (len=2)
PDR 0x0005 not found from wlan card PDA. Using default data.
len=2: 00 01
Plugging PDR 0x0006 at 0x007e14f0 (len=10)
Plugging PDR 0x0007 at 0x007e1504 (len=10)
Plugging PDR 0x0008 at 0x007e14c4 (len=8)
Plugging PDR 0x0400 at 0x007e1314 (len=2)
Plugging PDR 0x0402 at 0x007e131e (len=4)
Plugging PDR 0x0403 at 0x007e1316 (len=16)
Plugging PDR 0x0404 at 0x007e1326 (len=10)
Plugging PDR 0x0408 at 0x007e1312 (len=2)
PDR 0x0408 not found from wlan card PDA. Using default data.
len=2: 64 00
Plugging PDR 0x0001 at 0x007e14cc (len=16)
Plug record length mismatch (PDR=0x0001): 12 != 16
==> extend from default
PRI: old iface 1:1-3 new iface 1:4-4
Plugging PDR 0x0202 at 0x007f11ee (len=100)
Plugging PDR 0x0203 at 0x007f1252 (len=128)
Plugging PDR 0x0204 at 0x007f13d2 (len=80)
Plugging PDR 0x0405 at 0x007f1422 (len=4)
PDR 0x0405 not found from wlan card PDA. Using default data.
len=4: 00 00 00 30
Plugging PDR 0x0300 at 0x007f1426 (len=28)
Plugging PDR 0x0301 at 0x007f1442 (len=34)
Plugging PDR 0x0101 at 0x007f163a (len=6)
Plugging PDR 0x0103 at 0x007edd74 (len=12)
Plugging PDR 0x0104 at 0x007edeaa (len=2)
Plugging PDR 0x0105 at 0x007f1646 (len=2)
Plugging PDR 0x0105 at 0x007edee0 (len=2)
Plugging PDR 0x0105 at 0x007f1742 (len=2)
Plugging PDR 0x0107 at 0x007edd82 (len=2)
Plugging PDR 0x0006 at 0x007edd4e (len=10)
Plugging PDR 0x0406 at 0x007f16da (len=2)
PDR 0x0406 not found from wlan card PDA. Using default data.
len=2: 64 00
Plugging PDR 0x0302 at 0x007f146a (len=2)
PDR 0x0302 not found from wlan card PDA. Using default data.
len=2: 12 00
Plugging PDR 0x0303 at 0x007f146c (len=2)
PDR 0x0303 not found from wlan card PDA. Using default data.
len=2: ff 1f
Plugging PDR 0x0412 at 0x007edf02 (len=6)
PDR 0x0412 not found from wlan card PDA. Using default data.
len=6: ff ff 02 00 02 00
Generating CRC-16 (start=0x007e1800, len=65414) at 0x007e17fe
Allowing S3 overlap due to CRC-16 signature at 0x007e17fe (was: ffff)
After srec file merge
S3 area count: 5
addr=0x007E0000..0x007E0B55 (len=2902)
addr=0x007E0C00..0x007E151F (len=2336)
addr=0x007E17FE..0x007EE28D (len=51856)
addr=0x007F0800..0x007F1785 (len=3974)
addr=0x007FE000..0x007FECC5 (len=3270)
Total data length: 64338
OK.
Downloading to non-volatile memory (flash).
Note! This can take about 30 seconds. Do _not_ remove card during download.
ioctl[PRISM2_IOCTL_DOWNLOAD]: Operation not permitted
Download failed!
/var/log/messages:
Nov 2 00:11:07 linux kernel: hostap_crypt: registered algorithm 'NULL'
Nov 2 00:11:07 linux kernel: hostap_pci: 0.1.1 - 2003-10-19 (Jouni
Malinen <jkmaline at cc.hut.fi>)
Nov 2 00:11:07 linux kernel: hostap_pci: Registered netdevice wlan0
Nov 2 00:11:08 linux kernel: prism2_hw_init: initialized in 198 ms
Nov 2 00:11:08 linux kernel: wlan0: trying to read PDA from 0x007f0000: OK
Nov 2 00:11:08 linux kernel: wlan0: NIC: id=0x8013 v1.0.0
Nov 2 00:11:08 linux kernel: wlan0: PRI: id=0x15 v1.0.5
Nov 2 00:11:08 linux kernel: wlan0: STA: id=0x1f v1.3.4
Nov 2 00:11:08 linux kernel: wlan0: defaulting to host-based encryption
as a workaround for firmware bug in Host AP mode WEP
Nov 2 00:11:08 linux kernel: wlan0: defaulting to bogus WDS frame as a
workaround for firmware bug in Host AP mode WDS
Nov 2 00:11:08 linux kernel: wlan0: Intersil Prism2.5 PCI:
mem=0xcddff000, irq=11
Nov 2 00:11:16 linux /etc/hotplug/net.agent[1900]: No HW description
found ... exiting
Nov 2 00:14:38 linux kernel: prism2_download: dl_cmd=3
start_addr=0x00000000 num_areas=5
Nov 2 00:14:38 linux kernel: area 0: addr=0x007e0000 len=2902
ptr=0x080527f8
Nov 2 00:14:38 linux kernel: area 1: addr=0x007e0c00 len=2336
ptr=0x08053358
Nov 2 00:14:38 linux kernel: area 2: addr=0x007e17fe len=51856
ptr=0x08056db8
Nov 2 00:14:38 linux kernel: area 3: addr=0x007f0800 len=3974
ptr=0x0804fb48
Nov 2 00:14:38 linux kernel: area 4: addr=0x007fe000 len=3270
ptr=0x08050ad8
Nov 2 00:14:38 linux kernel: Download buffer: 4096 bytes at 0x0060:0x0000
Nov 2 00:14:44 linux kernel: prism2_hw_init: initialized in 82 ms
Nov 2 00:14:44 linux kernel: wlan0: starting flash download
Nov 2 00:14:44 linux kernel: hostap_pci: card initialization timed out
Nov 2 00:14:44 linux kernel: wlan0: Card configuration after flash
download failed
Nov 2 00:15:05 linux kernel: wlan0: hfa384x_cmd: entry still in list?
(entry=c943f280, type=0, res=0)
Nov 2 00:15:05 linux kernel: wlan0: hfa384x_cmd: command was not
completed (res=0, entry=c943f280, type=0, cmd=0x0021, param0=0xfdc6,
EVSTAT=8010 INTEN=0000)
Nov 2 00:15:05 linux kernel: wlan0: interrupt delivery does not seem to
work
Nov 2 00:15:05 linux kernel: wlan0: hfa384x_get_rid: CMDCODE_ACCESS
failed (res=-110, rid=fdc6, len=12)
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_cmd: entry still in list?
(entry=c943f280, type=0, res=0)
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_cmd: command was not
completed (res=0, entry=c943f280, type=0, cmd=0x0021, param0=0xfdc6,
EVSTAT=8010 INTEN=0000)
Nov 2 00:15:07 linux kernel: wlan0: interrupt delivery does not seem to
work
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_get_rid: CMDCODE_ACCESS
failed (res=-110, rid=fdc6, len=12)
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_cmd_issue: cmd reg was busy
for 5000 usec
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_cmd_issue - timeout -
reg=0x8021
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_cmd: entry still in list?
(entry=c943f280, type=0, res=-1)
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_cmd: interrupted; err=-110
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_get_rid: CMDCODE_ACCESS
failed (res=-110, rid=fdc1, len=2)
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_cmd_issue: cmd reg was busy
for 5000 usec
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_cmd_issue - timeout -
reg=0x8021
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_cmd: entry still in list?
(entry=c943f280, type=0, res=-1)
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_cmd: interrupted; err=-110
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_get_rid: CMDCODE_ACCESS
failed (res=-110, rid=fc06, len=2)
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_cmd_issue: cmd reg was busy
for 5000 usec
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_cmd_issue - timeout -
reg=0x8021
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_cmd: entry still in list?
(entry=c943f280, type=0, res=-1)
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_cmd: interrupted; err=-110
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_get_rid: CMDCODE_ACCESS
failed (res=-110, rid=fd42, len=6)
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_cmd_issue: cmd reg was busy
for 5000 usec
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_cmd_issue - timeout -
reg=0x8021
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_cmd: entry still in list?
(entry=c943f440, type=0, res=-1)
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_cmd: interrupted; err=-110
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_get_rid: CMDCODE_ACCESS
failed (res=-110, rid=fc0e, len=34)
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_cmd_issue: cmd reg was busy
for 5000 usec
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_cmd_issue - timeout -
reg=0x8021
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_cmd: entry still in list?
(entry=c943f280, type=0, res=-1)
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_cmd: interrupted; err=-110
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_get_rid: CMDCODE_ACCESS
failed (res=-110, rid=fc84, len=2)
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_cmd_issue: cmd reg was busy
for 5000 usec
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_cmd_issue - timeout -
reg=0x8021
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_cmd: entry still in list?
(entry=c943f280, type=0, res=-1)
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_cmd: interrupted; err=-110
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_get_rid: CMDCODE_ACCESS
failed (res=-110, rid=fc83, len=2)
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_cmd_issue: cmd reg was busy
for 5000 usec
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_cmd_issue - timeout -
reg=0x8021
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_cmd: entry still in list?
(entry=c943f280, type=0, res=-1)
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_cmd: interrupted; err=-110
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_get_rid: CMDCODE_ACCESS
failed (res=-110, rid=fc82, len=2)
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_cmd_issue: cmd reg was busy
for 5000 usec
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_cmd_issue - timeout -
reg=0x8021
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_cmd: entry still in list?
(entry=c943f280, type=0, res=-1)
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_cmd: interrupted; err=-110
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_get_rid: CMDCODE_ACCESS
failed (res=-110, rid=fc09, len=2)
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_cmd_issue: cmd reg was busy
for 5000 usec
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_cmd_issue - timeout -
reg=0x8021
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_cmd: entry still in list?
(entry=c943f280, type=0, res=-1)
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_cmd: interrupted; err=-110
Nov 2 00:15:07 linux kernel: wlan0: hfa384x_get_rid: CMDCODE_ACCESS
failed (res=-110, rid=fd48, len=2)
Nov 2 00:16:18 linux kernel: hostap_pci: Driver unloaded
Nov 2 00:16:18 linux kernel: hostap_crypt: unregistered algorithm
'NULL' (deinit)
Nov 2 00:16:26 linux /etc/hotplug/net.agent[1950]: No HW description
found ... exiting
Nov 2 00:16:36 linux kernel: hostap_crypt: registered algorithm 'NULL'
Nov 2 00:16:36 linux kernel: hostap_pci: 0.1.1 - 2003-10-19 (Jouni
Malinen <jkmaline at cc.hut.fi>)
Nov 2 00:16:36 linux kernel: hostap_pci: Registered netdevice wlan0
Nov 2 00:16:36 linux kernel: hostap_pci: card initialization timed out
Nov 2 00:16:36 linux kernel: hostap_pci: hardware initialization failed
Nov 2 00:16:36 linux kernel: hostap_pci: No devices found, driver not
installed.
Nov 2 00:16:36 linux kernel: hostap_crypt: unregistered algorithm
'NULL' (deinit)
Nov 2 00:16:36 linux kernel: hostap_crypt: registered algorithm 'NULL'
Nov 2 00:16:36 linux kernel: hostap_pci: 0.1.1 - 2003-10-19 (Jouni
Malinen <jkmaline at cc.hut.fi>)
Nov 2 00:16:36 linux kernel: hostap_pci: Registered netdevice wlan0
Nov 2 00:16:37 linux kernel: hostap_pci: card initialization timed out
Nov 2 00:16:37 linux kernel: hostap_pci: hardware initialization failed
Nov 2 00:16:37 linux kernel: hostap_pci: No devices found, driver not
installed.
Nov 2 00:16:37 linux kernel: hostap_crypt: unregistered algorithm
'NULL' (deinit)
Nov 2 00:16:44 linux /etc/hotplug/net.agent[1976]: No HW description
found ... exiting
Nov 2 00:16:44 linux /etc/hotplug/net.agent[1993]: No HW description
found ... exiting
Nov 2 00:16:44 linux /etc/hotplug/net.agent[2010]: No HW description
found ... exiting
Nov 2 00:16:45 linux /etc/hotplug/net.agent[2028]: No HW description
found ... exiting
Nov 2 00:18:18 linux modprobe: modprobe: Can't locate module wlan0
A try to load the driver:
modprobe hostap_pci
/lib/modules/2.4.20-4GB-athlon/net/hostap_pci.o: init_module: No such device
Hint: insmod errors can be caused by incorrect module parameters,
including invalid IO or IRQ parameters.
You may find more information in syslog or the output from dmesg
/lib/modules/2.4.20-4GB-athlon/net/hostap_pci.o: insmod
/lib/modules/2.4.20-4GB-athlon/net/hostap_pci.o failed
/lib/modules/2.4.20-4GB-athlon/net/hostap_pci.o: insmod hostap_pci failed
==> /var/log/messages <==
Nov 2 22:16:53 falzeben kernel: hostap_crypt: registered algorithm 'NULL'
Nov 2 22:16:53 falzeben kernel: hostap_pci: 0.0.3 - 2003-05-18 (Jouni
Malinen <jkmaline at cc.hut.fi>)
Nov 2 22:16:53 falzeben kernel: hostap_pci: Registered netdevice wlan0
Nov 2 22:16:53 falzeben kernel: prism2_hw_init()
Nov 2 22:16:53 falzeben kernel: hostap_pci: card initialization timed out
Nov 2 22:16:53 falzeben kernel: hostap_pci: Initialization failed
Nov 2 22:16:53 falzeben kernel: hostap_pci: hardware initialization failed
Nov 2 22:16:54 falzeben kernel: hostap_pci: Netdevice wlan0 unregistered
Nov 2 22:16:54 falzeben kernel: hostap_pci: No devices found, driver
not installed.
Nov 2 22:16:54 falzeben kernel: hostap_crypt: unregistered algorithm
'NULL' (deinit)
More information about the Hostap
mailing list