PDA and other files for WPC11 v2.5 ?

[I C Pitcher]

I have inherited an 'ill' Linksys WPC11 (ver2.5) PCMCIA card.

I suspect that there is a problem with its firmware, so am trying to flash it to a "known good" linksys firmware (the one from their website).

Winupdate will not see the card so I have resorted to the Intersil DOS flash utility which detects the card and attempts to program it however, it starts off with 
"PD item 405 not in PDA. Using default in hex file."
"PD item 406 not in PDA. Using default in hex file."

and then later finishes off with 

"Bad status 64c0 auxDisable failed!Download FAILED."
"ERROR ENCOUNTERED"


If someone has access to a PDA file for this card I would be grateful, also the "Initial" firmware file for the 2.5 Prism card.

I hope this makes sense.

NB I've tried the card in the linux box and get the following dmesg output:
hostap_cs, can anyone diagnose anything ? 

setting Vcc=50 (from config)
Checking CFTABLE_ENTRY 0x01 (default 0x01)
IO window settings: cfg->io.nwin=1 dflt.io.nwin=1
io->flags = 0x0046, io.base=0x0000, len=64
hostap_cs: index 0x01: Vcc 5.0, irq 3, io 0x0100-0x013f
hostap_cs: Registered netdevice wlan0
prism2_hw_init()
prism2_hw_config: initialized in 17152 iterations
wlan0: hfa384x_cmd: entry still in list? (entry=c1899960, type=0, res=0)
wlan0: hfa384x_cmd: command was not completed (res=0, entry=c1899960, type=0, cmd=0x0021, param0=0xfd0b, EVSTAT=8010)
wlan0: interrupt delivery does not seem to work
wlan0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fd0b, len=8)
Could not get RID for component NIC
wlan0: hfa384x_cmd: entry still in list? (entry=c1899960, type=0, res=0)
wlan0: hfa384x_cmd: command was not completed (res=0, entry=c1899960, type=0, cmd=0x0021, param0=0xfd02, EVSTAT=8010)
wlan0: interrupt delivery does not seem to work
wlan0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fd02, len=8)
Could not get RID for component PRI
wlan0: hfa384x_cmd_issue: cmd reg was busy for 1000 usec
wlan0: hfa384x_cmd_issue - timeout - reg=0x8021
wlan0: hfa384x_cmd: entry still in list? (entry=c1899960, type=0, res=-1)
wlan0: hfa384x_cmd: interrupted; err=-110
wlan0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fd20, len=8)
Could not get RID for component STA
wlan0: hfa384x_cmd_issue: cmd reg was busy for 1000 usec
wlan0: hfa384x_cmd_issue - timeout - reg=0x8021
wlan0: hfa384x_cmd: entry still in list? (entry=c1899960, type=0, res=-1)
wlan0: hfa384x_cmd: interrupted; err=-110
wlan0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fd20, len=8)
wlan0: hfa384x_cmd_issue: cmd reg was busy for 1000 usec
wlan0: hfa384x_cmd_issue - timeout - reg=0x8021
wlan0: hfa384x_cmd: entry still in list? (entry=c1899960, type=0, res=-1)
wlan0: hfa384x_cmd: interrupted; err=-110
wlan0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fc01, len=6)
wlan0: could not get own MAC address
wlan0: hfa384x_cmd_issue: cmd reg was busy for 1000 usec
wlan0: hfa384x_cmd_issue - timeout - reg=0x8000
wlan0: hfa384x_cmd: entry still in list? (entry=c1899960, type=0, res=-1)
wlan0: hfa384x_cmd: interrupted; err=-110
wlan0: hfa384x_set_rid: CMDCODE_ACCESS_WRITE failed (res=-110, rid=fc00, len=2)
wlan0: Port type setting to 6 failed
wlan0: hfa384x_cmd_issue: cmd reg was busy for 1000 usec
wlan0: hfa384x_cmd_issue - timeout - reg=0x8000
wlan0: hfa384x_cmd: entry still in list? (entry=c1899960, type=0, res=-1)
wlan0: hfa384x_cmd: interrupted; err=-110
wlan0: MAC port 0 enabling failed


Cheers

Ian