[PATCH 2/2] ARM: boards: remove obsolete PCA9450_RESET_CTRL setup

[Ahmad Fatoum]

Hello Jonas,

On 3/11/25 12:21, Jonas Rebmann wrote:
> Hi Ahmad,
> 
> Not so much. As mentioned in the cover, the imx8 boards routinely
> configure a larger array of pca9450 registers. As I didn't give the rest
> of that setup a closer look, I did not change the code.

Ah, should've read the cover letter, my bad.

Please add that information into the commit messages, so it becomes
part of the git history.

> I have only tested this series on the phyboard segin imx93.
> 
> Just like with the imx93 boards, after application of the driver patch,
> the { PCA9450_RESET_CTRL, 0xA1 } lines in lowlevel.c should no more have
> an effect (as no board currently uses nxp,wdog_b-warm-reset).
> 
> Should I remove all { PCA9450_RESET_CTRL, 0xA1 } configuration in v2?

An explanation in the commit message why this wasn't done is enough.

Cheers,
Ahmad

> 
>  - Jonas
> 
> On 2025-03-11 12:03, Ahmad Fatoum wrote:
>> Hi,
>>
>> On 3/11/25 11:50, Jonas Rebmann wrote:
>>> Since a previous commit, PCA9450_RESET_CTRL is initialized to 0xA1 in
>>> pca9450_probe; explicitly setting this in board.c has no effect anymore.
>>
>> Note that there is a number of i.MX8M boards that also use the PCA9450
>> and configure 0xA1 into PCA9450_RESET_CTRL in their lowlevel.c.
>>
>> Any particular reason against or for dropping the configuration there?
>>
>> Thanks,
>> Ahmad
>>
>>> Signed-off-by: Jonas Rebmann <jre at pengutronix.de>
>>> ---
>>>   arch/arm/boards/phytec-phycore-imx93/board.c | 9 ---------
>>>   arch/arm/boards/tqma93xx/board.c             | 3 ---
>>>   2 files changed, 12 deletions(-)
>>>
>>> diff --git a/arch/arm/boards/phytec-phycore-imx93/board.c b/arch/arm/
>>> boards/phytec-phycore-imx93/board.c
>>> index
>>> 149248ca654624826d0e8f6fe0f1f42c2747e248..03ba8cb5026d2a9eaa054fcfc69e18872fcd658e 100644
>>> --- a/arch/arm/boards/phytec-phycore-imx93/board.c
>>> +++ b/arch/arm/boards/phytec-phycore-imx93/board.c
>>> @@ -6,23 +6,14 @@
>>>   #include <init.h>
>>>   #include <linux/kernel.h>
>>>   #include <environment.h>
>>> -#include <mfd/pca9450.h>
>>>   #include <deep-probe.h>
>>>   #include <mach/imx/bbu.h>
>>>   #include <linux/pinctrl/consumer.h>
>>>   -static void phycore_imx93_init_pmic(struct regmap *map)
>>> -{
>>> -    /* set WDOG_B_CFG to cold reset */
>>> -    regmap_write(map, PCA9450_RESET_CTRL, 0xA1);
>>> -}
>>> -
>>>   static int phycore_imx93_probe(struct device *dev)
>>>   {
>>>       struct device_node *np;
>>>   -    pca9450_register_init_callback(phycore_imx93_init_pmic);
>>> -
>>>       /*
>>>        * The phy on the EQOS has its MDIO lines connected to the FEC.
>>> The phy
>>>        * registers can only be successfully read when the EQOS
>>> pinctrl setup
>>> diff --git a/arch/arm/boards/tqma93xx/board.c b/arch/arm/boards/
>>> tqma93xx/board.c
>>> index
>>> b181784079cf12e5a112d13f95c87c2cf5ebeba6..b4de6c2f6c347cb255537a3784a667a9c2607de3 100644
>>> --- a/arch/arm/boards/tqma93xx/board.c
>>> +++ b/arch/arm/boards/tqma93xx/board.c
>>> @@ -27,9 +27,6 @@ static void tqma93xx_init_pmic(struct regmap *map)
>>>         /* I2C_LT_EN*/
>>>       regmap_write(map, 0xa, 0x3);
>>> -
>>> -    /* set WDOG_B_CFG to cold reset */
>>> -    regmap_write(map, PCA9450_RESET_CTRL, 0xA1);
>>>   }
>>>     static int tqma93xx_probe(struct device *dev)
>>>
>>
>>
>>
> 
>