[PATCH 3/5] ARM: mach-imx: tzasc: add region configure helpers

Ahmad Fatoum a.fatoum at pengutronix.de
Tue Jun 24 03:40:12 PDT 2025



On 6/19/25 17:25, Marco Felsch wrote:
> At the moment the TZC380 driver is very limited and focused on minimal
> platform setup unlike the TZC400 driver.
> 
> This commit adds helper functions to setup any number of TZASC regions
> of any size which is required by later commits to setup an early
> non-secure TZASC region1.
> 
> The code is based on the TZC400 barebox driver and the TZC380 OP-TEE
> driver.
> 
> Signed-off-by: Marco Felsch <m.felsch at pengutronix.de>

Acked-by: Ahmad Fatoum <a.fatoum at pengutronix.de>

> ---
>  arch/arm/mach-imx/tzasc.c | 235 ++++++++++++++++++++++++++++++++++++++
>  1 file changed, 235 insertions(+)
> 
> diff --git a/arch/arm/mach-imx/tzasc.c b/arch/arm/mach-imx/tzasc.c
> index 4cb4d7c5cffc..4f6da6016601 100644
> --- a/arch/arm/mach-imx/tzasc.c
> +++ b/arch/arm/mach-imx/tzasc.c
> @@ -1,11 +1,76 @@
>  // SPDX-License-Identifier: GPL-2.0-only
>  
> +#define pr_fmt(fmt) "tzc380: " fmt
> +
> +#include <common.h>
>  #include <mach/imx/generic.h>
>  #include <mach/imx/tzasc.h>
> +#include <linux/bitfield.h>
>  #include <linux/bitops.h>
> +#include <linux/log2.h>
> +#include <linux/sizes.h>
>  #include <mach/imx/imx8m-regs.h>
>  #include <io.h>
>  
> +/*******************************************************************************
> + *                         TZC380 defines
> + ******************************************************************************/
> +
> +#define TZC380_BUILD_CONFIG		0x000
> +#define   TZC380_BUILD_CONFIG_AW	GENMASK(13, 8)
> +#define   TZC380_BUILD_CONFIG_NR	GENMASK(4, 0)
> +
> +/*
> + * All TZC region configuration registers are placed one after another. It
> + * depicts size of block of registers for programming each region.
> + */
> +#define TZC380_REGION_REG_SIZE		0x10
> +
> +#define TZC380_REGION_SETUP_LOW_0	0x100
> +#define TZC380_REGION_SETUP_HIGH_0	0x104
> +#define TZC380_REGION_ATTR_0		0x108
> +#define   TZC380_REGION_SP		GENMASK(31, 28)
> +#define   TZC380_SUBREGION_DIS_MASK	GENMASK(15, 8)
> +#define   TZC380_REGION_SIZE		GENMASK(6, 1)
> +#define   TZC380_REGION_EN		BIT(0)
> +
> +/* ID Registers */
> +#define TZC380_PID0_OFF			0xfe0
> +#define TZC380_PID1_OFF			0xfe4
> +#define   TZC380_PERIPHERAL_ID		0x380
> +#define TZC380_PID2_OFF			0xfe8
> +#define TZC380_PID3_OFF			0xfec
> +#define TZC380_PID4_OFF			0xfd0
> +#define TZC380_CID0_OFF			0xff0
> +#define TZC380_CID1_OFF			0xff4
> +#define TZC380_CID2_OFF			0xff8
> +
> +#define TZC380_REGION_OFFSET(region_no)		\
> +		(TZC380_REGION_REG_SIZE * (region_no))
> +#define TZC380_REGION_SETUP_LOW(region_no)	\
> +		(TZC380_REGION_OFFSET(region_no) + TZC380_REGION_SETUP_LOW_0)
> +#define TZC380_REGION_SETUP_HIGH(region_no)	\
> +		(TZC380_REGION_OFFSET(region_no) + TZC380_REGION_SETUP_HIGH_0)
> +#define TZC380_REGION_ATTR(region_no)		\
> +		(TZC380_REGION_OFFSET(region_no) + TZC380_REGION_ATTR_0)
> +
> +#define TZC380_REGION_SP_NS_W		FIELD_PREP(TZC380_REGION_SP, BIT(0))
> +#define TZC380_REGION_SP_NS_R		FIELD_PREP(TZC380_REGION_SP, BIT(1))
> +#define TZC380_REGION_SP_S_W		FIELD_PREP(TZC380_REGION_SP, BIT(2))
> +#define TZC380_REGION_SP_S_R		FIELD_PREP(TZC380_REGION_SP, BIT(3))
> +
> +#define TZC380_REGION_SP_ALL		\
> +		(TZC380_REGION_SP_NS_W | TZC380_REGION_SP_NS_R | \
> +		 TZC380_REGION_SP_S_W | TZC380_REGION_SP_S_R)
> +#define TZC380_REGION_SP_S_RW		\
> +		(TZC380_REGION_SP_S_W | TZC380_REGION_SP_S_R)
> +#define TZC380_REGION_SP_NS_RW		\
> +		(TZC380_REGION_SP_NS_W | TZC380_REGION_SP_NS_R)
> +
> +/*******************************************************************************
> + *                         SoC specific defines
> + ******************************************************************************/
> +
>  #define GPR_TZASC_EN					BIT(0)
>  #define GPR_TZASC_ID_SWAP_BYPASS		BIT(1)
>  #define GPR_TZASC_EN_LOCK				BIT(16)
> @@ -14,6 +79,176 @@
>  #define MX8M_TZASC_REGION_ATTRIBUTES_0		(MX8M_TZASC_BASE_ADDR + 0x108)
>  #define MX8M_TZASC_REGION_ATTRIBUTES_0_SP	GENMASK(31, 28)
>  
> +/*
> + * Implementation defined values used to validate inputs later.
> + * Filters : max of 4 ; 0 to 3
> + * Regions : max of 9 ; 0 to 8
> + * Address width : Values between 32 to 64
> + */
> +struct tzc380_instance {
> +	void __iomem *base;
> +	uint8_t addr_width;
> +	uint8_t num_regions;
> +};
> +/* Some platforms like i.MX6 does have two tzc380 controllers */
> +static struct tzc380_instance tzc380_inst[2];
> +
> +static inline unsigned int tzc_read_peripheral_id(void __iomem *base)
> +{
> +	unsigned int id;
> +
> +	id = in_le32(base + TZC380_PID0_OFF);
> +	/* Masks DESC part in PID1 */
> +	id |= ((in_le32(base + TZC380_PID1_OFF) & 0xFU) << 8U);
> +
> +	return id;
> +}
> +
> +static struct tzc380_instance *tzc380_init(void __iomem *base)
> +{
> +	struct tzc380_instance *tzc380 = &tzc380_inst[0];
> +	unsigned int tzc380_id;
> +	unsigned int tzc380_build;
> +
> +	if (tzc380->base)
> +		tzc380 = &tzc380_inst[1];
> +
> +	if (tzc380->base)
> +		panic("TZC-380: No free memory\n");
> +
> +	tzc380->base = base;
> +
> +	tzc380_id = tzc_read_peripheral_id(base);
> +	if (tzc380_id != TZC380_PERIPHERAL_ID)
> +		panic("TZC-380 : Wrong device ID (0x%x).\n", tzc380_id);
> +
> +	/* Save values we will use later. */
> +	tzc380_build = in_le32(base + TZC380_BUILD_CONFIG);
> +	tzc380->addr_width  = FIELD_GET(TZC380_BUILD_CONFIG_AW, tzc380_build) + 1;
> +	tzc380->num_regions = FIELD_GET(TZC380_BUILD_CONFIG_NR, tzc380_build) + 1;
> +
> +	return tzc380;
> +}
> +
> +static void
> +tzc380_configure_region(struct tzc380_instance *tzc380, unsigned int region,
> +			uint64_t region_base, unsigned int region_attr)
> +{
> +	void __iomem *base = tzc380->base;
> +
> +	/* Do range checks on regions */
> +	ASSERT((region < tzc380->num_regions));
> +
> +	pr_debug("TrustZone : Configuring region %u\n", region);
> +	pr_debug("TrustZone : ... base = %#llx\n", region_base);
> +	pr_debug("TrustZone : ... sp = %#x\n",
> +		 (unsigned int)FIELD_GET(TZC380_REGION_SP, region_attr));
> +	pr_debug("TrustZone : ... subregion dis-mask = %#x\n",
> +		 (unsigned int)FIELD_GET(TZC380_SUBREGION_DIS_MASK, region_attr));
> +	pr_debug("TrustZone : ... size = %#x\n",
> +		 (unsigned int)FIELD_GET(TZC380_REGION_SIZE, region_attr));
> +	pr_debug("TrustZone : ... enable = %#x\n",
> +		 (unsigned int)FIELD_GET(TZC380_REGION_EN, region_attr));
> +
> +	/***************************************************/
> +	/* Inputs look ok, start programming registers.    */
> +	/* The address registers are 32 bits wide and      */
> +	/* have a LOW and HIGH				   */
> +	/* component used to construct an address up to a  */
> +	/* 64bit.					   */
> +	/***************************************************/
> +	out_le32(base + TZC380_REGION_SETUP_LOW(region), (uint32_t)region_base);
> +	out_le32(base + TZC380_REGION_SETUP_HIGH(region), (uint32_t)(region_base >> 32));
> +
> +	/* Set region attributes */
> +	out_le32(base + TZC380_REGION_ATTR(region), region_attr);
> +}
> +
> +static int
> +tzc380_auto_configure(struct tzc380_instance *tzc380, unsigned int region,
> +		      uint64_t base, uint64_t size,
> +		      unsigned int attr)
> +{
> +	uint64_t sub_region_size = 0;
> +	uint64_t area = 0;
> +	uint8_t lregion = region;
> +	uint64_t region_size = 0;
> +	uint64_t sub_address = 0;
> +	uint64_t address = base;
> +	uint64_t lsize = size;
> +	unsigned int lattr;
> +	uint32_t mask = 0;
> +	uint64_t reminder;
> +	int i = 0;
> +	uint8_t pow = 0;
> +
> +	ASSERT(tzc380->base);
> +
> +	/*
> +	 * TZC380 RM
> +	 * For region_attributes_<n> registers, region_size:
> +	 * Note: The AXI address width, that is AXI_ADDRESS_MSB+1, controls the
> +	 * upper limit value of the field.
> +	 */
> +	pow = tzc380->addr_width;
> +
> +	while (lsize != 0 && pow >= 15) {
> +		region_size = 1ULL << pow;
> +
> +		/* Case region fits alignment and covers requested area */
> +		if ((address % region_size == 0) &&
> +		    ((address + lsize) % region_size == 0)) {
> +			lattr = attr;
> +			lattr |= FIELD_PREP(TZC380_REGION_SIZE, (pow - 1));
> +			lattr |= TZC380_REGION_EN;
> +
> +			tzc380_configure_region(tzc380, lregion, address, lattr);
> +
> +			lregion++;
> +			address += region_size;
> +			lsize -= region_size;
> +			pow = tzc380->addr_width;
> +			continue;
> +		}
> +
> +		/* Cover area using several subregions */
> +		sub_region_size = div_u64(region_size, 8);
> +		div64_u64_rem(address, sub_region_size, &reminder);
> +		if (reminder == 0 && lsize > 2 * sub_region_size) {
> +			sub_address = div64_u64(address, region_size) * region_size;
> +			mask = 0;
> +			for (i = 0; i < 8; i++) {
> +				area = (i + 1) * sub_region_size;
> +				if (sub_address + area <= address ||
> +				    sub_address + area > address + lsize) {
> +					mask |= FIELD_PREP(TZC380_SUBREGION_DIS_MASK, BIT(i));
> +				} else {
> +					address += sub_region_size;
> +					lsize -= sub_region_size;
> +				}
> +			}
> +
> +			lattr = mask | attr;
> +			lattr |= FIELD_PREP(TZC380_REGION_SIZE, (pow - 1));
> +			lattr |= TZC380_REGION_EN;
> +
> +			tzc380_configure_region(tzc380, lregion, sub_address, lattr);
> +
> +			lregion++;
> +			pow = tzc380->addr_width;
> +			continue;
> +		}
> +		pow--;
> +	}
> +	ASSERT(lsize == 0);
> +	ASSERT(address == base + size);
> +	return lregion;
> +}
> +
> +/******************************************************************************
> + *                          SoC specific helpers
> + ******************************************************************************/
> +
>  void imx8m_tzc380_init(void)
>  {
>  	u32 __iomem *gpr = IOMEM(MX8M_IOMUXC_GPR_BASE_ADDR);

-- 
Pengutronix e.K.                  |                             |
Steuerwalder Str. 21              | http://www.pengutronix.de/  |
31137 Hildesheim, Germany         | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686  | Fax:   +49-5121-206917-5555 |




More information about the barebox mailing list