[PATCH 3/6] net: phy: micrel: add support for ksz9131 phy
Stefan Kerkmann
s.kerkmann at pengutronix.de
Mon Mar 11 02:10:10 PDT 2024
From: Marc Kleine-Budde <mkl at pengutronix.de>
This imports the micrel KSZ9131 gigabit phy driver from Linux, commit
0316c7e66bbd16cf2d01a4e2f5afa6afb01278f2.
Signed-off-by: Marc Kleine-Budde <mkl at pengutronix.de>
Signed-off-by: Stefan Kerkmann <s.kerkmann at pengutronix.de>
---
drivers/net/phy/micrel.c | 188 +++++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 188 insertions(+)
diff --git a/drivers/net/phy/micrel.c b/drivers/net/phy/micrel.c
index 36cc857a2c..a203669353 100644
--- a/drivers/net/phy/micrel.c
+++ b/drivers/net/phy/micrel.c
@@ -546,6 +546,186 @@ static int ksz9031_config_init(struct phy_device *phydev)
return ret;
}
+#define KSZ9131_SKEW_5BIT_MAX 2400
+#define KSZ9131_SKEW_4BIT_MAX 800
+#define KSZ9131_OFFSET 700
+#define KSZ9131_STEP 100
+
+static int ksz9131_of_load_skew_values(struct phy_device *phydev,
+ const struct device_node *of_node,
+ u16 reg, size_t field_sz,
+ const char *field[], u8 numfields)
+{
+ int val[4] = {-(1 + KSZ9131_OFFSET), -(2 + KSZ9131_OFFSET),
+ -(3 + KSZ9131_OFFSET), -(4 + KSZ9131_OFFSET)};
+ int skewval, skewmax = 0;
+ int matches = 0;
+ u16 maxval;
+ u16 newval;
+ u16 mask;
+ int i;
+
+ /* psec properties in dts should mean x pico seconds */
+ if (field_sz == 5)
+ skewmax = KSZ9131_SKEW_5BIT_MAX;
+ else
+ skewmax = KSZ9131_SKEW_4BIT_MAX;
+
+ for (i = 0; i < numfields; i++)
+ if (!of_property_read_s32(of_node, field[i], &skewval)) {
+ if (skewval < -KSZ9131_OFFSET)
+ skewval = -KSZ9131_OFFSET;
+ else if (skewval > skewmax)
+ skewval = skewmax;
+
+ val[i] = skewval + KSZ9131_OFFSET;
+ matches++;
+ }
+
+ if (!matches)
+ return 0;
+
+ if (matches < numfields)
+ newval = phy_read_mmd(phydev, 2, reg);
+ else
+ newval = 0;
+
+ maxval = (field_sz == 4) ? 0xf : 0x1f;
+ for (i = 0; i < numfields; i++)
+ if (val[i] != -(i + 1 + KSZ9131_OFFSET)) {
+ mask = 0xffff;
+ mask ^= maxval << (field_sz * i);
+ newval = (newval & mask) |
+ (((val[i] / KSZ9131_STEP) & maxval)
+ << (field_sz * i));
+ }
+
+ return phy_write_mmd(phydev, 2, reg, newval);
+}
+
+#define KSZ9131RN_MMD_COMMON_CTRL_REG 2
+#define KSZ9131RN_RXC_DLL_CTRL 76
+#define KSZ9131RN_TXC_DLL_CTRL 77
+#define KSZ9131RN_DLL_CTRL_BYPASS BIT_MASK(12)
+#define KSZ9131RN_DLL_ENABLE_DELAY 0
+#define KSZ9131RN_DLL_DISABLE_DELAY BIT(12)
+
+static int ksz9131_config_rgmii_delay(struct phy_device *phydev)
+{
+ u16 rxcdll_val, txcdll_val;
+ int ret;
+
+ switch (phydev->interface) {
+ case PHY_INTERFACE_MODE_RGMII:
+ rxcdll_val = KSZ9131RN_DLL_DISABLE_DELAY;
+ txcdll_val = KSZ9131RN_DLL_DISABLE_DELAY;
+ break;
+ case PHY_INTERFACE_MODE_RGMII_ID:
+ rxcdll_val = KSZ9131RN_DLL_ENABLE_DELAY;
+ txcdll_val = KSZ9131RN_DLL_ENABLE_DELAY;
+ break;
+ case PHY_INTERFACE_MODE_RGMII_RXID:
+ rxcdll_val = KSZ9131RN_DLL_ENABLE_DELAY;
+ txcdll_val = KSZ9131RN_DLL_DISABLE_DELAY;
+ break;
+ case PHY_INTERFACE_MODE_RGMII_TXID:
+ rxcdll_val = KSZ9131RN_DLL_DISABLE_DELAY;
+ txcdll_val = KSZ9131RN_DLL_ENABLE_DELAY;
+ break;
+ default:
+ return 0;
+ }
+
+ ret = phy_modify_mmd(phydev, KSZ9131RN_MMD_COMMON_CTRL_REG,
+ KSZ9131RN_RXC_DLL_CTRL, KSZ9131RN_DLL_CTRL_BYPASS,
+ rxcdll_val);
+ if (ret < 0)
+ return ret;
+
+ return phy_modify_mmd(phydev, KSZ9131RN_MMD_COMMON_CTRL_REG,
+ KSZ9131RN_TXC_DLL_CTRL, KSZ9131RN_DLL_CTRL_BYPASS,
+ txcdll_val);
+}
+
+/* Silicon Errata DS80000693B
+ *
+ * When LEDs are configured in Individual Mode, LED1 is ON in a no-link
+ * condition. Workaround is to set register 0x1e, bit 9, this way LED1 behaves
+ * according to the datasheet (off if there is no link).
+ */
+static int ksz9131_led_errata(struct phy_device *phydev)
+{
+ int reg;
+
+ reg = phy_read_mmd(phydev, 2, 0);
+ if (reg < 0)
+ return reg;
+
+ if (!(reg & BIT(4)))
+ return 0;
+
+ return phy_set_bits(phydev, 0x1e, BIT(9));
+}
+
+static int ksz9131_config_init(struct phy_device *phydev)
+{
+ const struct device *dev = &phydev->dev;
+ const struct device_node *of_node = dev->of_node;
+ static const char *clk_skews[2] = {"rxc-skew-psec", "txc-skew-psec"};
+ static const char *rx_data_skews[4] = {
+ "rxd0-skew-psec", "rxd1-skew-psec",
+ "rxd2-skew-psec", "rxd3-skew-psec"
+ };
+ static const char *tx_data_skews[4] = {
+ "txd0-skew-psec", "txd1-skew-psec",
+ "txd2-skew-psec", "txd3-skew-psec"
+ };
+ static const char *control_skews[2] = {"txen-skew-psec", "rxdv-skew-psec"};
+ int ret;
+
+ if (!of_node && dev->parent->of_node)
+ of_node = dev->parent->of_node;
+
+ if (!of_node)
+ return 0;
+
+ if (phy_interface_is_rgmii(phydev)) {
+ ret = ksz9131_config_rgmii_delay(phydev);
+ if (ret < 0)
+ return ret;
+ }
+
+ ret = ksz9131_of_load_skew_values(phydev, of_node,
+ MII_KSZ9031RN_CLK_PAD_SKEW, 5,
+ clk_skews, 2);
+ if (ret < 0)
+ return ret;
+
+ ret = ksz9131_of_load_skew_values(phydev, of_node,
+ MII_KSZ9031RN_CONTROL_PAD_SKEW, 4,
+ control_skews, 2);
+ if (ret < 0)
+ return ret;
+
+ ret = ksz9131_of_load_skew_values(phydev, of_node,
+ MII_KSZ9031RN_RX_DATA_PAD_SKEW, 4,
+ rx_data_skews, 4);
+ if (ret < 0)
+ return ret;
+
+ ret = ksz9131_of_load_skew_values(phydev, of_node,
+ MII_KSZ9031RN_TX_DATA_PAD_SKEW, 4,
+ tx_data_skews, 4);
+ if (ret < 0)
+ return ret;
+
+ ret = ksz9131_led_errata(phydev);
+ if (ret < 0)
+ return ret;
+
+ return 0;
+}
+
#define KSZ8873MLL_GLOBAL_CONTROL_4 0x06
#define KSZ8873MLL_GLOBAL_CONTROL_4_DUPLEX BIT(6)
#define KSZ8873MLL_GLOBAL_CONTROL_4_SPEED BIT(4)
@@ -757,6 +937,14 @@ static struct phy_driver ksphy_driver[] = {
.config_init = ksz9031_config_init,
.config_aneg = genphy_config_aneg,
.read_status = ksz9031_read_status,
+}, {
+ .phy_id = PHY_ID_KSZ9131,
+ .phy_id_mask = 0x00fffff0,
+ .drv.name = "Microchip KSZ9131 Gigabit PHY",
+ .features = (PHY_GBIT_FEATURES | SUPPORTED_Pause),
+ .config_init = ksz9131_config_init,
+ .config_aneg = genphy_config_aneg,
+ .read_status = genphy_read_status,
}, {
.phy_id = PHY_ID_KSZ8873MLL,
.phy_id_mask = 0x00fffff0,
--
2.39.2
More information about the barebox
mailing list