[PATCH 059/112] efi: payload: init: restrict barebox mem to first 1G only on x86
Ahmad Fatoum
a.fatoum at pengutronix.de
Sun Jan 7 23:22:31 PST 2024
On 05.01.24 15:58, Michael Olbrich wrote:
> On Fri, Jan 05, 2024 at 11:41:09AM +0100, Ahmad Fatoum wrote:
>> On 05.01.24 10:31, Michael Olbrich wrote:
>>> On Fri, Jan 05, 2024 at 10:14:33AM +0100, Ahmad Fatoum wrote:
>>>> On 04.01.24 19:10, Michael Olbrich wrote:
>>>>> On Thu, Jan 04, 2024 at 12:17:12PM +0100, Ahmad Fatoum wrote:
>>>>>> On 03.01.24 19:58, Michael Olbrich wrote:
>>>>>>> On Wed, Jan 03, 2024 at 07:12:19PM +0100, Ahmad Fatoum wrote:
>>>>>>>> When run as EFI payload, barebox will not have full access to DRAM and will
>>>>>>>> have to ask the EFI firmware for memory. It does so once at the beginning
>>>>>>>> and since commit 356aaef5a37d ("efi: improve malloc pool allocation"),
>>>>>>>> the buffer was always placed beneath the 1G boundary.
>>>>>>>>
>>>>>>>> Aforementioned commit didn't elaborate why a maximum of 1G in particular
>>>>>>>> was chosen. Anyways, non-PC architectures have different memory maps, so
>>>>>>>> a 1G limit doesn't make sense there. Therefore restrict the limit to
>>>>>>>> ARCH_X86. On non-x86, we allow the memory pages to be located anywhere.
>>>>>>>
>>>>>>> The 1G is somewhat arbitrary but if you don't restrict the memory to 32bit,
>>>>>>> then loading the kernel may fail: The addresses in "struct
>>>>>>> linux_kernel_header" are only 32bit. So if you impose no restrictions at
>>>>>>> all, then this memory cannot be used for the kernel and initrd.
>>>>>>
>>>>>> The limit for x86 remains at 1G. It's only for other architectures, that we
>>>>>> remove the limit. I suspect that other architectures won't have this kind
>>>>>> of problems though , because they would boot the kernel image via EFI load
>>>>>> and start image boot services, where the EFI firmware takes care to layout
>>>>>> the boot artifacts.
>>>>>>
>>>>>> Once we have that in place, we could even use it on x86 instead of
>>>>>> using struct linux_kernel_header, but I haven't investigated this yet.
>>>>>
>>>>> How do you load the initrd via EFI? As far as I know, that only works as a
>>>>> filename in the EFI boot partition.
>>>>
>>>> This seems to be relaxed in newer kernels, see
>>>> https://lore.kernel.org/linux-efi/20200207202637.GA3464906@rani.riverdale.lan/T/
>>>
>>> It's not quite clear to me how that works, but from what I can tell,
>>> requires support from the firmware and barebox needs to use it. So that
>>> does not help here.
>>> You need to either disable the legacy handler to avoid arbitrary failures
>>> or explicitly allocate the initrd memory from efi with the restriction to
>>> <4G.
>>
>> The legacy handler wouldn't apply to other architectures:
>>
>> - The Kernel images for ARM64 and RISC-V have different more-specific filetypes
>> than filetype_exe
>
> Ah, now I get it. I forgot that that code is x86 specific. So how do you
> boot Linux from EFI anyways on other architectures?
We don't yet.
> I don't see any filetypes for EFI binaries for other architectures. I'm not
> sure how that works but would expect to find some code that hands over
> efi_sys_table? Or what am I missing?
Only binfmt handler is registered for normal EFI start. initrd/DT will have
to follow later.
> And if you boot a non-EFI binary shouldn't you call RS->exit_boot_services()
> before actually starting the kernel?
Possibly. I remember that booting a kernel without EFI stub failed, but haven't
investigated why this was the case.
> And we should move setting LoaderTimeExecUSec into some kind of barebox
> shutdown handler to ensure that it is set even if other bootm handlers are
> used. But that's all unrelated to this patch.
Yes. I'll keep that in mind for when the bootm handler is added.
Thanks,
Ahmad
>
> Regards,
> Michael
>
>> - The Linux kernel header check will probabaly fail for every format that's not
>> x86
>>
>> Cheers,
>> Ahmad
>>
>>>
>>> Michael
>>>
>>>>> That was the reason for implementing
>>>>> the "legacy" boot mode. And what about the device-tree?
>>>>
>>>> There is an EFI config table for FDT (DEVICE_TREE_GUID in Linux code). barebox
>>>> as EFI loader can use it to provide its own DT. I have to check what's the cleanest
>>>> way for barebox as EFI payload to provide a different DT, but I hope there is a way
>>>> without barebox as EFI payload having to manipulate the device tree itself.
>>>>
>>>> Cheers,
>>>> Ahmad
>>>>
>>>>>
>>>>> Michael
>>>>>
>>>>>>>> This can break PCI drivers on systems that so far assumed barebox memory
>>>>>>>> is located in the first 4G, but that's ok. That code will need to be
>>>>>>>> fixed eventually anyway.
>>>>>>>>
>>>>>>>> Cc: Michael Olbrich <m.olbrich at pengutronix.de>
>>>>>>>> Signed-off-by: Ahmad Fatoum <a.fatoum at pengutronix.de>
>>>>>>>> ---
>>>>>>>> efi/payload/init.c | 2 +-
>>>>>>>> 1 file changed, 1 insertion(+), 1 deletion(-)
>>>>>>>>
>>>>>>>> diff --git a/efi/payload/init.c b/efi/payload/init.c
>>>>>>>> index 4b612e61afb3..0c2f38e9c86a 100644
>>>>>>>> --- a/efi/payload/init.c
>>>>>>>> +++ b/efi/payload/init.c
>>>>>>>> @@ -292,7 +292,7 @@ void efi_main(efi_handle_t image, struct efi_system_table *sys_table)
>>>>>>>> BS->handle_protocol(efi_loaded_image->device_handle,
>>>>>>>> &efi_device_path_protocol_guid, (void **)&efi_device_path);
>>>>>>>>
>>>>>>>> - mem = 0x3fffffff;
>>>>>>>> + mem = IS_ENABLED(CONFIG_X86) ? 0x3fffffff : ~0ULL;
>>>>>>>> for (memsize = SZ_256M; memsize >= SZ_8M; memsize /= 2) {
>>>>>>>> efiret = BS->allocate_pages(EFI_ALLOCATE_MAX_ADDRESS,
>>>>>>>> EFI_LOADER_DATA,
>>>>>>>> --
>>>>>>>> 2.39.2
>>>>>>>>
>>>>>>>>
>>>>>>>
>>>>>>
>>>>>> --
>>>>>> Pengutronix e.K. | |
>>>>>> Steuerwalder Str. 21 | http://www.pengutronix.de/ |
>>>>>> 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
>>>>>> Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
>>>>>>
>>>>>>
>>>>>
>>>>
>>>> --
>>>> Pengutronix e.K. | |
>>>> Steuerwalder Str. 21 | http://www.pengutronix.de/ |
>>>> 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
>>>> Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
>>>>
>>>>
>>>
>>
>> --
>> Pengutronix e.K. | |
>> Steuerwalder Str. 21 | http://www.pengutronix.de/ |
>> 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
>> Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
>>
>>
>>
>
--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
More information about the barebox
mailing list