[PATCH] ARM: dts: phycore-stm32mp15: Use upstream dts
Sascha Hauer
s.hauer at pengutronix.de
Wed Sep 20 04:29:32 PDT 2023
The phycore-stm32mp15 board has long been mainlined. Switch the
board to use the upstream dts files.
This at least has the effect that now the PMIC is probed as our
downstream dts hasn't enabled the i2c4 node.
Signed-off-by: Sascha Hauer <s.hauer at pengutronix.de>
---
.../dts/stm32mp157c-phycore-stm32mp1-3.dts | 16 +-
...stm32mp157c-phycore-stm32mp15-pinctrl.dtsi | 92 ------
.../stm32mp157c-phycore-stm32mp15-som.dtsi | 271 ------------------
3 files changed, 2 insertions(+), 377 deletions(-)
delete mode 100644 arch/arm/dts/stm32mp157c-phycore-stm32mp15-pinctrl.dtsi
delete mode 100644 arch/arm/dts/stm32mp157c-phycore-stm32mp15-som.dtsi
diff --git a/arch/arm/dts/stm32mp157c-phycore-stm32mp1-3.dts b/arch/arm/dts/stm32mp157c-phycore-stm32mp1-3.dts
index a34a2a337f..02540b560e 100644
--- a/arch/arm/dts/stm32mp157c-phycore-stm32mp1-3.dts
+++ b/arch/arm/dts/stm32mp157c-phycore-stm32mp1-3.dts
@@ -6,12 +6,8 @@
/dts-v1/;
-#include <dt-bindings/gpio/gpio.h>
-#include <arm/st/stm32mp157.dtsi>
-#include <arm/st/stm32mp15xc.dtsi>
-#include <arm/st/stm32mp15-pinctrl.dtsi>
-#include <arm/st/stm32mp15xxac-pinctrl.dtsi>
-#include "stm32mp157c-phycore-stm32mp15-som.dtsi"
+#include <arm/st/stm32mp157c-phycore-stm32mp1-3.dts>
+#include "stm32mp151.dtsi"
/ {
model = "PHYTEC phyCORE-STM32MP1-3 SoM";
@@ -31,11 +27,3 @@ environment-emmc {
};
};
};
-
-&sdmmc1 {
- status = "okay";
-};
-
-&sdmmc2 {
- status = "okay";
-};
diff --git a/arch/arm/dts/stm32mp157c-phycore-stm32mp15-pinctrl.dtsi b/arch/arm/dts/stm32mp157c-phycore-stm32mp15-pinctrl.dtsi
deleted file mode 100644
index aa41006c23..0000000000
--- a/arch/arm/dts/stm32mp157c-phycore-stm32mp15-pinctrl.dtsi
+++ /dev/null
@@ -1,92 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
-/*
- * Copyright (C) Phytec GmbH 2019-2020 - All Rights Reserved
- * Author: Dom VOVARD <dom.vovard at linrt.com>.
- */
-#include <arm/st/stm32mp15-pinctrl.dtsi>
-
-ðernet0_rgmii_pins_a {
- pins1 {
- pinmux = <STM32_PINMUX('G', 4, AF11)>, /* ETH_RGMII_GTX_CLK */
- <STM32_PINMUX('G', 13, AF11)>, /* ETH_RGMII_TXD0 */
- <STM32_PINMUX('G', 14, AF11)>, /* ETH_RGMII_TXD1 */
- <STM32_PINMUX('C', 2, AF11)>, /* ETH_RGMII_TXD2 */
- <STM32_PINMUX('E', 2, AF11)>, /* ETH_RGMII_TXD3 */
- <STM32_PINMUX('B', 11, AF11)>, /* ETH_RGMII_TX_CTL */
- <STM32_PINMUX('A', 2, AF11)>, /* ETH_MDIO */
- <STM32_PINMUX('C', 1, AF11)>; /* ETH_MDC */
- bias-disable;
- drive-push-pull;
- slew-rate = <2>;
- };
- pins2 {
- pinmux = <STM32_PINMUX('C', 4, AF11)>, /* ETH_RGMII_RXD0 */
- <STM32_PINMUX('C', 5, AF11)>, /* ETH_RGMII_RXD1 */
- <STM32_PINMUX('H', 6, AF11)>, /* ETH_RGMII_RXD2 */
- <STM32_PINMUX('B', 1, AF11)>, /* ETH_RGMII_RXD3 */
- <STM32_PINMUX('A', 1, AF11)>, /* ETH_RGMII_RX_CLK */
- <STM32_PINMUX('A', 7, AF11)>; /* ETH_RGMII_RX_CTL */
- bias-disable;
- };
-};
-
-&pinctrl {
- sdmmc1_dir_pins_b: sdmmc1-dir-1 {
- pins1 {
- pinmux = <STM32_PINMUX('E', 12, AF8)>, /* SDMMC1_D0DIR */
- <STM32_PINMUX('E', 14, AF11)>, /* SDMMC1_D123DIR */
- <STM32_PINMUX('B', 9, AF11)>; /* SDMMC1_CDIR */
- slew-rate = <3>;
- drive-push-pull;
- bias-pull-up;
- };
- pins2 {
- pinmux = <STM32_PINMUX('E', 4, AF8)>; /* SDMMC1_CKIN */
- bias-pull-up;
- };
- };
-};
-
-&sdmmc1_b4_pins_a {
- pins1 {
- pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
- <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
- <STM32_PINMUX('E', 6, AF8)>, /* SDMMC1_D2 */
- <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */
- <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
- slew-rate = <1>;
- drive-push-pull;
- bias-disable;
- };
- pins2 {
- pinmux = <STM32_PINMUX('C', 12, AF12)>; /* SDMMC1_CK */
- slew-rate = <2>;
- drive-push-pull;
- bias-disable;
- };
-};
-
-&sdmmc2_d47_pins_a {
- pins {
- pinmux = <STM32_PINMUX('A', 8, AF9)>, /* SDMMC2_D4 */
- <STM32_PINMUX('A', 9, AF10)>, /* SDMMC2_D5 */
- <STM32_PINMUX('C', 6, AF10)>, /* SDMMC2_D6 */
- <STM32_PINMUX('D', 3, AF9)>; /* SDMMC2_D7 */
- slew-rate = <1>;
- drive-push-pull;
- bias-pull-up;
- };
-};
-
-&uart4_pins_a {
- pins1 {
- pinmux = <STM32_PINMUX('B', 9, AF8)>; /* UART4_TX */
- bias-disable;
- drive-push-pull;
- slew-rate = <0>;
- };
- pins2 {
- pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */
- bias-disable;
- };
-};
diff --git a/arch/arm/dts/stm32mp157c-phycore-stm32mp15-som.dtsi b/arch/arm/dts/stm32mp157c-phycore-stm32mp15-som.dtsi
deleted file mode 100644
index a40e59ae2e..0000000000
--- a/arch/arm/dts/stm32mp157c-phycore-stm32mp15-som.dtsi
+++ /dev/null
@@ -1,271 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause)
-/*
- * Copyright (C) Phytec GmbH 2019-2020 - All Rights Reserved
- * Author: Dom VOVARD <dom.vovard at linrt.com>.
- */
-
-#include "stm32mp157c-phycore-stm32mp15-pinctrl.dtsi"
-#include <dt-bindings/net/ti-dp83867.h>
-#include "stm32mp151.dtsi"
-
-/ {
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- aliases {
- serial0 = &uart4;
- serial1 = &usart3;
- };
-
- vin: vin {
- compatible = "regulator-fixed";
- regulator-name = "vin";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- regulator-always-on;
- };
-
- pwr_irq: pwr at 50001020 {
- compatible = "st,stm32mp1-pwr";
- reg = <0x50001020 0x100>;
- };
-};
-
-&bsec {
- board_id: board_id at ec {
- reg = <0xec 0x4>;
- st,non-secure-otp;
- };
-};
-
-&clk_hse {
- st,digbypass;
-};
-
-&cpu0 {
- cpu-supply = <&vddcore>;
-};
-
-&cpu1 {
- cpu-supply = <&vddcore>;
-};
-
-ðernet0 {
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <ðernet0_rgmii_pins_a>;
- pinctrl-1 = <ðernet0_rgmii_sleep_pins_a>;
- phy-mode = "rgmii-id";
- phy-handle = <ðphy>;
- max-speed = <1000>;
- st,eth-clk-sel;
- status = "okay";
-
- mdio0 {
- compatible = "snps,dwmac-mdio";
- #address-cells = <1>;
- #size-cells = <0>;
-
- ethphy: ethernet-phy at 1 {
- reg = <1>;
- };
- };
-};
-
-&i2c4 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c4_pins_a>;
- i2c-scl-rising-time-ns = <185>;
- i2c-scl-falling-time-ns = <20>;
-
- pmic: stpmic at 33 {
- compatible = "st,stpmic1";
- reg = <0x33>;
-
- regulators {
- compatible = "st,stpmic1-regulators";
- buck1-supply = <&vin>;
- buck2-supply = <&vin>;
- buck3-supply = <&vin>;
- buck4-supply = <&vin>;
- ldo1-supply = <&v3v3>;
- ldo2-supply = <&v3v3>;
- ldo3-supply = <&vdd_ddr>;
- ldo4-supply = <&vin>;
- ldo5-supply = <&v3v3>;
- ldo6-supply = <&v3v3>;
- vref_ddr-supply = <&vin>;
- boost-supply = <&vin>;
- pwr_sw1-supply = <&bst_out>;
- pwr_sw2-supply = <&bst_out>;
-
- vddcore: buck1 {
- regulator-name = "vddcore";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- regulator-initial-mode = <0>;
- regulator-over-current-protection;
- };
-
- vdd_ddr: buck2 {
- regulator-name = "vdd_ddr";
- regulator-min-microvolt = <1350000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- regulator-initial-mode = <0>;
- regulator-over-current-protection;
- };
-
- vdd: buck3 {
- regulator-name = "vdd";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- st,mask-reset;
- regulator-initial-mode = <0>;
- regulator-over-current-protection;
- };
-
- v3v3: buck4 {
- regulator-name = "v3v3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- regulator-over-current-protection;
- regulator-initial-mode = <0>;
- };
-
- v1v8_audio: ldo1 {
- regulator-name = "v1v8_audio";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- vdd_eth_2v5: ldo2 {
- regulator-name = "vdd_eth_2v5";
- regulator-min-microvolt = <2500000>;
- regulator-max-microvolt = <2500000>;
- regulator-always-on;
- };
-
- vtt_ddr: ldo3 {
- regulator-name = "vtt_ddr";
- regulator-min-microvolt = <500000>;
- regulator-max-microvolt = <750000>;
- regulator-always-on;
- regulator-over-current-protection;
- };
-
- vdd_usb: ldo4 {
- regulator-name = "vdd_usb";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
- vdda: ldo5 {
- regulator-name = "vdda";
- regulator-min-microvolt = <2900000>;
- regulator-max-microvolt = <2900000>;
- regulator-boot-on;
- };
-
- vdd_eth_1v0: ldo6 {
- regulator-name = "vdd_eth_1v0";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- };
-
- vref_ddr: vref_ddr {
- regulator-name = "vref_ddr";
- regulator-always-on;
- regulator-over-current-protection;
- };
-
- bst_out: boost {
- regulator-name = "bst_out";
- };
-
- vbus_otg: pwr_sw1 {
- regulator-name = "vbus_otg";
- };
-
- vbus_sw: pwr_sw2 {
- regulator-name = "vbus_sw";
- regulator-active-discharge = <1>;
- };
- };
- };
-};
-
-&iwdg2 {
- timeout-sec = <32>;
- status = "okay";
-};
-
-&pwr_regulators {
- vdd-supply = <&vdd>;
- vdd_3v3_usbfs-supply = <&vdd_usb>;
-};
-
-&rng1 {
- status = "okay";
-};
-
-&sdmmc1 {
- pinctrl-names = "default";
- pinctrl-0 = <&sdmmc1_b4_pins_a>;
- disable-wp;
- st,neg-edge;
- bus-width = <4>;
- vmmc-supply = <&v3v3>;
- status = "disabled";
-};
-
-&sdmmc2 {
- pinctrl-names = "default";
- pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
- non-removable;
- no-sd;
- no-sdio;
- st,neg-edge;
- bus-width = <8>;
- vmmc-supply = <&v3v3>;
- vqmmc-supply = <&v3v3>;
- mmc-ddr-3_3v;
- status = "disabled";
-};
-
-&uart4 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart4_pins_a>;
- status = "okay";
-};
-
-&usart3 {
- pinctrl-names = "default";
- pinctrl-0 = <&usart3_pins_a>;
- status = "disabled";
-};
-
-&usbotg_hs {
- phys = <&usbphyc_port1 0>;
- phy-names = "usb2-phy";
- usb-role-switch;
- status = "okay";
-};
-
-&usbphyc {
- status = "okay";
-};
-
-&usbphyc_port0 {
- phy-supply = <&vdd_usb>;
-};
-
-&usbphyc_port1 {
- phy-supply = <&vdd_usb>;
-};
--
2.39.2
More information about the barebox
mailing list