[PATCH] ARM: arria10: xload: retry FPGA configuration

[Steffen Trumtrar]

From: Bruno Knittel <bruno.knittel at bruker.com>

The Intel documentation states that the FPGA configuration might fail.
This has been observed on the Enclustra AA1+ board where up to 4 retries
where required to configure the FPGA.

Debugging session showed that the data where correctly read from the
eMMC but yet the configuration failed.

This commit introduces a retry loop on the FPGA configuration.
Up to 10 retries (arbitrary) are attempted.
As the hardware can't be used anyway without the FPGA loaded, this
doesn't introduce any boot time problems. Taking longer is better than
just hang()ing.

Signed-off-by: Bruno Knittel <bruno.knittel at bruker.com>
Signed-off-by: Steffen Trumtrar <s.trumtrar at pengutronix.de>
---
 arch/arm/mach-socfpga/arria10-xload.c | 47 +++++++++++++++++----------
 1 file changed, 30 insertions(+), 17 deletions(-)

diff --git a/arch/arm/mach-socfpga/arria10-xload.c b/arch/arm/mach-socfpga/arria10-xload.c
index 9d54a1de58..0e49452c17 100644
--- a/arch/arm/mach-socfpga/arria10-xload.c
+++ b/arch/arm/mach-socfpga/arria10-xload.c
@@ -359,33 +359,46 @@ int arria10_load_fpga(int offset, int bitstream_size)
 	int ret;
 	uint32_t count;
 	uint32_t size = bitstream_size / SECTOR_SIZE;
+	uint32_t retryCount;
 
 	if (offset)
 		offset = offset / SECTOR_SIZE;
 
-	count = offset;
+	/* Up to 4 retires have been seen on the Enclustra Mercury AA1+ board, as FPGA configuration is mandatory
+	 * to be able to continue the boot, take some margin and try up to 10 times
+	 */
+	for (retryCount = 0; retryCount < 10; ++retryCount) {
+		count = offset;
 
-	arria10_read_blocks(buf, count + bitstream.first_sec, SZ_16K);
+		arria10_read_blocks(buf, count + bitstream.first_sec, SZ_16K);
 
-	count += SZ_16K / SECTOR_SIZE;
+		count += SZ_16K / SECTOR_SIZE;
 
-	ret = a10_fpga_init(buf);
-	if (ret)
-		hang();
+		ret = a10_fpga_init(buf);
+		if (ret)
+			continue;
 
-	while (count <= size) {
-		ret = a10_fpga_write(buf, SZ_16K);
-		if (ret == -ENOSPC)
-			break;
-		count += SZ_16K / SECTOR_SIZE;
-		ret = arria10_read_blocks(buf, count, SZ_16K);
-	}
+		while (count <= size) {
+			ret = a10_fpga_write(buf, SZ_16K);
+			if (ret == -ENOSPC)
+				continue;
 
-	ret = a10_fpga_write_complete();
-	if (ret)
-		hang();
+			count += SZ_16K / SECTOR_SIZE;
+			ret = arria10_read_blocks(buf, count, SZ_16K);
+			// Reading failed, consider this a failed attempt to configure the FPGA and retry
+			if (ret)
+				continue;
+		}
 
-	return 0;
+		ret = a10_fpga_write_complete();
+		if (ret)
+			continue;
+
+		return 0;
+	}
+
+	hang();
+	return -EIO;
 }
 
 void arria10_start_image(int offset)
-- 
2.41.0