[PATCH master] clk: ti-sci: fix build failure without TI_SCI_PROTOCOL

[Sascha Hauer]

On Mon, Dec 04, 2023 at 05:52:38PM +0100, Ahmad Fatoum wrote:
> The SCI clk driver has an unconditional reference to
> ti_sci_get_handle(), but no dependency is specific in the Kconfig.
> Add a dependency and change defaults, so it's enabled by default.
> 
> Signed-off-by: Ahmad Fatoum <a.fatoum at pengutronix.de>
> ---
>  drivers/clk/Kconfig      | 9 +++++++++
>  drivers/clk/Makefile     | 2 +-
>  drivers/firmware/Kconfig | 1 +
>  3 files changed, 11 insertions(+), 1 deletion(-)

Applied, thanks

Sascha

> 
> diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig
> index 076e77c8590f..a3772ed56d2a 100644
> --- a/drivers/clk/Kconfig
> +++ b/drivers/clk/Kconfig
> @@ -38,6 +38,15 @@ config COMMON_CLK_SCMI
>  	  This driver uses SCMI Message Protocol to interact with the
>  	  firmware providing all the clock controls.
>  
> +config TI_SCI_CLK
> +	tristate "TI System Control Interface clock drivers"
> +	depends on TI_SCI_PROTOCOL
> +	default ARCH_K3
> +	help
> +	  This adds the clock driver support over TI System Control Interface.
> +	  If you wish to use clock resources from the PMMC firmware, say Y.
> +	  Otherwise, say N.
> +
>  config COMMON_CLK_GPIO
>  	bool
>  	default y
> diff --git a/drivers/clk/Makefile b/drivers/clk/Makefile
> index 3ebafbf7fdad..3a2983c0a030 100644
> --- a/drivers/clk/Makefile
> +++ b/drivers/clk/Makefile
> @@ -29,4 +29,4 @@ obj-$(CONFIG_MACH_RPI_COMMON)	+= clk-rpi.o
>  obj-y				+= bcm/
>  obj-$(CONFIG_COMMON_CLK_SCMI)	+= clk-scmi.o
>  obj-$(CONFIG_COMMON_CLK_GPIO)   += clk-gpio.o
> -obj-$(CONFIG_ARCH_K3)		+= ti-sci-clk.o
> +obj-$(CONFIG_TI_SCI_CLK)	+= ti-sci-clk.o
> diff --git a/drivers/firmware/Kconfig b/drivers/firmware/Kconfig
> index ee91b2b7fa6d..e37099aa6141 100644
> --- a/drivers/firmware/Kconfig
> +++ b/drivers/firmware/Kconfig
> @@ -46,6 +46,7 @@ config QEMU_FW_CFG
>  config TI_SCI_PROTOCOL
>  	bool "TI System Control Interface (TISCI) Message Protocol"
>  	depends on TI_MESSAGE_MANAGER
> +	default ARCH_K3
>  	help
>  	  TI System Control Interface (TISCI) Message Protocol is used to manage
>  	  compute systems such as ARM, DSP etc with the system controller in
> -- 
> 2.39.2
> 
> 
> 

-- 
Pengutronix e.K.                           |                             |
Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |