[PATCH 4/4] ARM: dts: imx8mp-debix-som-a-bmb-08-upstream: sync with mainlined kernel version
Marco Felsch
m.felsch at pengutronix.de
Tue Aug 29 05:43:56 PDT 2023
Sync the *-upstream.dts(i) versions with the mainlined kernel version [1]
available with v6.6.
[1] https://lore.kernel.org/all/20230809071026.3546605-4-m.felsch@pengutronix.de/
Signed-off-by: Marco Felsch <m.felsch at pengutronix.de>
---
.../imx8mp-debix-som-a-bmb-08-upstream.dts | 126 ++++++++----------
arch/arm/dts/imx8mp-debix-som-a-upstream.dtsi | 36 +++--
2 files changed, 85 insertions(+), 77 deletions(-)
diff --git a/arch/arm/dts/imx8mp-debix-som-a-bmb-08-upstream.dts b/arch/arm/dts/imx8mp-debix-som-a-bmb-08-upstream.dts
index 79c505d141c2..59334ce30c8a 100644
--- a/arch/arm/dts/imx8mp-debix-som-a-bmb-08-upstream.dts
+++ b/arch/arm/dts/imx8mp-debix-som-a-bmb-08-upstream.dts
@@ -11,20 +11,27 @@
/ {
model = "Polyhex i.MX8MPlus Debix SOM A on BMB-08";
compatible = "polyhex,imx8mp-debix-som-a-bmb-08", "polyhex,imx8mp-debix-som-a",
- "polyhex,imx8mp-debix", "fsl,imx8mp";
+ "fsl,imx8mp";
+
+ aliases {
+ ethernet0 = &eqos;
+ ethernet1 = &fec;
+ };
chosen {
stdout-path = &uart2;
};
- regulator-baseboard-vdd3v3 {
+ reg_baseboard_vdd3v3: regulator-baseboard-vdd3v3 {
compatible = "regulator-fixed";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "BB_VDD3V3";
+ /* Required timings for ethernet phy's */
+ startup-delay-us = <50000>;
+ off-on-delay-us = <110000>;
gpio = <&expander0 10 GPIO_ACTIVE_HIGH>;
enable-active-high;
- regulator-always-on;
};
reg_baseboard_vdd5v0: regulator-baseboard-vdd5v0 {
@@ -56,17 +63,6 @@ regulator-som-vdd3v3 {
regulator-always-on;
};
- reg_usdhc2_vmmc: regulator-usdhc2 {
- compatible = "regulator-fixed";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
- regulator-name = "VSD_3V3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
regulator-vbus-usb20 {
compatible = "regulator-fixed";
regulator-min-microvolt = <5000000>;
@@ -102,10 +98,11 @@ reg_vdd5v0: regulator-vdd5v0 {
&eqos {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_eqos>;
- phy-mode = "rgmii-id";
+ nvmem-cells = <ðmac1>;
+ nvmem-cell-names = "mac-address";
+ phy-supply = <®_baseboard_vdd3v3>;
phy-handle = <ðphy0>;
- snps,reset-gpio = <&gpio4 18 GPIO_ACTIVE_LOW>;
- snps,reset-delays-us = <10 20 200000>;
+ phy-mode = "rgmii-id";
status = "okay";
mdio {
@@ -113,16 +110,14 @@ mdio {
#address-cells = <1>;
#size-cells = <0>;
- ethphy0: ethernet-phy at 0 {
+ ethphy0: ethernet-phy at 1 {
compatible = "ethernet-phy-ieee802.3-c22";
- reg = <0>;
- qca,disable-smarteee;
- vddio-supply = <&vddio_phy0>;
-
- vddio_phy0: vddio-phy0-regulator {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
+ reg = <1>;
+ reset-gpios = <&gpio4 18 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <20000>;
+ reset-deassert-us = <150000>;
+ eee-broken-1000t;
+ realtek,clkout-disable;
};
};
};
@@ -130,28 +125,26 @@ vddio_phy0: vddio-phy0-regulator {
&fec {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_fec>;
- phy-mode = "rgmii-id";
+ nvmem-cells = <ðmac2>;
+ nvmem-cell-names = "mac-address";
+ phy-supply = <®_baseboard_vdd3v3>;
phy-handle = <ðphy1>;
+ phy-mode = "rgmii-id";
fsl,magic-packet;
- phy-reset-gpios = <&gpio4 19 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <10>;
- phy-reset-post-delay = <150>;
status = "okay";
mdio {
#address-cells = <1>;
#size-cells = <0>;
- ethphy1: ethernet-phy at 0 {
+ ethphy1: ethernet-phy at 1 {
compatible = "ethernet-phy-ieee802.3-c22";
- reg = <0>;
- qca,disable-smarteee;
- vddio-supply = <&vddio_phy1>;
-
- vddio_phy1: vddio-phy1-regulator {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
+ reg = <1>;
+ reset-gpios = <&gpio4 19 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <20000>;
+ reset-deassert-us = <150000>;
+ eee-broken-1000t;
+ realtek,clkout-disable;
};
};
};
@@ -201,7 +194,7 @@ expander1: gpio at 23 {
#gpio-cells = <0x02>;
/*
- * Since USB1 is binded to peripheral mode we need to ensure
+ * Since USB1 is bound to peripheral mode we need to ensure
* that VBUS is turned off.
*/
usb30-otg-hog {
@@ -212,12 +205,6 @@ usb30-otg-hog {
};
};
- eeprom at 52 {
- compatible = "atmel,24c02";
- reg = <0x52>;
- pagesize = <16>;
- };
-
rtc at 51 {
compatible = "haoyu,hym8563";
reg = <0x51>;
@@ -227,6 +214,23 @@ rtc at 51 {
interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
#clock-cells = <0>;
};
+
+ eeprom at 52 {
+ compatible = "atmel,24c02";
+ reg = <0x52>;
+ pagesize = <16>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* MACs stored in ASCII */
+ ethmac1: mac-address at 0 {
+ reg = <0x0 0xc>;
+ };
+
+ ethmac2: mac-address at c {
+ reg = <0xc 0xc>;
+ };
+ };
};
&snvs_pwrkey {
@@ -301,16 +305,16 @@ &usb3_phy1 {
/* µSD Card */
&usdhc2 {
pinctrl-names = "default", "state_100mhz", "state_200mhz";
- pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
- pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
- pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
- cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
- vmmc-supply = <®_usdhc2_vmmc>;
- bus-width = <4>;
-
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
assigned-clocks = <&clk IMX8MP_CLK_USDHC2>;
assigned-clock-rates = <400000000>;
-
+ vmmc-supply = <®_usdhc2_vmmc>;
+ bus-width = <4>;
+ disable-wp;
+ no-sdio;
+ no-mmc;
status = "okay";
};
@@ -409,12 +413,6 @@ MX8MP_IOMUXC_GPIO1_IO03__GPIO1_IO03 0x41
>;
};
- pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
- fsl,pins = <
- MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19 0x41
- >;
- };
-
pinctrl_uart2: uart2grp {
fsl,pins = <
MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX 0x14f
@@ -468,13 +466,7 @@ MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d6
MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d6
MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d6
MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d6
- MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1
- >;
- };
-
- pinctrl_usdhc2_gpio: usdhc2gpiogrp {
- fsl,pins = <
- MX8MP_IOMUXC_SD2_CD_B__GPIO2_IO12 0x1c4
+ MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1
>;
};
};
diff --git a/arch/arm/dts/imx8mp-debix-som-a-upstream.dtsi b/arch/arm/dts/imx8mp-debix-som-a-upstream.dtsi
index ae12f322bce2..9e0d19a2a72c 100644
--- a/arch/arm/dts/imx8mp-debix-som-a-upstream.dtsi
+++ b/arch/arm/dts/imx8mp-debix-som-a-upstream.dtsi
@@ -8,7 +8,18 @@
/ {
model = "Polyhex i.MX8MPlus Debix SOM A";
- compatible = "polyhex,imx8mp-debix-som-a", "polyhex,imx8mp-debix", "fsl,imx8mp";
+ compatible = "polyhex,imx8mp-debix-som-a", "fsl,imx8mp";
+
+ reg_usdhc2_vmmc: regulator-usdhc2 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
+ regulator-name = "VSD_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
};
&A53_0 {
@@ -38,9 +49,8 @@ pmic at 25 {
reg = <0x25>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pmic>;
-
interrupt-parent = <&gpio1>;
- interrupts = <3 GPIO_ACTIVE_LOW>;
+ interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
regulators {
buck1: BUCK1 {
@@ -63,7 +73,7 @@ buck2: BUCK2 {
nxp,dvs-standby-voltage = <850000>;
};
- buck4: BUCK4{
+ buck4: BUCK4 {
regulator-name = "BUCK4";
regulator-min-microvolt = <600000>;
regulator-max-microvolt = <3400000>;
@@ -71,7 +81,7 @@ buck4: BUCK4{
regulator-always-on;
};
- buck5: BUCK5{
+ buck5: BUCK5 {
regulator-name = "BUCK5";
regulator-min-microvolt = <600000>;
regulator-max-microvolt = <3400000>;
@@ -139,7 +149,6 @@ &i2c4 {
adc at 48 {
compatible = "ti,ads1115";
reg = <0x48>;
-
#address-cells = <1>;
#size-cells = <0>;
@@ -148,16 +157,19 @@ channel at 4 {
ti,gain = <1>;
ti,datarate = <7>;
};
+
channel at 5 {
reg = <5>;
ti,gain = <1>;
ti,datarate = <7>;
};
+
channel at 6 {
reg = <6>;
ti,gain = <1>;
ti,datarate = <7>;
};
+
channel at 7 {
reg = <7>;
ti,gain = <1>;
@@ -176,12 +188,10 @@ &usdhc3 {
pinctrl-0 = <&pinctrl_usdhc3>;
pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
- bus-width = <8>;
- non-removable;
-
assigned-clocks = <&clk IMX8MP_CLK_USDHC3>;
assigned-clock-rates = <400000000>;
-
+ bus-width = <8>;
+ non-removable;
status = "okay";
};
@@ -213,6 +223,12 @@ MX8MP_IOMUXC_GPIO1_IO03__GPIO1_IO03 0x41
>;
};
+ pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
+ fsl,pins = <
+ MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19 0x41
+ >;
+ };
+
pinctrl_usdhc3: usdhc3grp {
fsl,pins = <
MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x190
--
2.39.2
More information about the barebox
mailing list