[PATCH v2 06/11] ARM: at91: Add at91sam9 xload_mmc for PBL use
Sam Ravnborg
sam at ravnborg.org
Tue Jun 28 13:38:44 PDT 2022
Add xload support to at91sam9263 similar to what is already
present for the sama5d3.
The xload supports reading barebox.bin from a SDCARD from the
PBL and load the full barebox.bin and starts it.
Signed-off-by: Sam Ravnborg <sam at ravnborg.org>
---
arch/arm/mach-at91/Makefile | 1 +
arch/arm/mach-at91/at91sam9_xload_mmc.c | 118 ++++++++++++++++++++++++
arch/arm/mach-at91/include/mach/xload.h | 4 +
3 files changed, 123 insertions(+)
create mode 100644 arch/arm/mach-at91/at91sam9_xload_mmc.c
diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile
index 12e64291b..b171d682f 100644
--- a/arch/arm/mach-at91/Makefile
+++ b/arch/arm/mach-at91/Makefile
@@ -17,6 +17,7 @@ obj-y += at91sam9_reset.o
obj-y += at91sam9g45_reset.o
obj-pbl-$(CONFIG_HAVE_AT91_DDRAMC) += ddramc.o
pbl-$(CONFIG_AT91_MCI_PBL) += xload-mmc.o
+pbl-$(CONFIG_AT91_MCI_PBL) += at91sam9_xload_mmc.o
obj-$(CONFIG_AT91SAM9_SMC) += sam9_smc.o
obj-$(CONFIG_HAVE_AT91SAM9_RST) += at91sam9_rst.o
diff --git a/arch/arm/mach-at91/at91sam9_xload_mmc.c b/arch/arm/mach-at91/at91sam9_xload_mmc.c
new file mode 100644
index 000000000..64266757d
--- /dev/null
+++ b/arch/arm/mach-at91/at91sam9_xload_mmc.c
@@ -0,0 +1,118 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/* SPDX-FileCopyrightText: 2022 Sam Ravnborg */
+
+#include <debug_ll.h>
+#include <common.h>
+#include <pbl.h>
+
+#include <linux/sizes.h>
+#include <asm/cache.h>
+
+#include <mach/at91_pmc_ll.h>
+#include <mach/at91sam9263.h>
+#include <mach/at91sam926x.h>
+#include <mach/hardware.h>
+#include <mach/iomux.h>
+#include <mach/xload.h>
+#include <mach/gpio.h>
+
+typedef void (*func)(int zero, int arch, void *params);
+
+/*
+ * Load barebox.bin and start executing the first byte in the barebox image.
+ * barebox.bin is loaded to AT91_CHIPSELECT_1.
+ *
+ * To be able to load barebox.bin do a minimal init of the pheriferals
+ * used by MCI.
+ * This functions runs in PBL code and uses the PBL variant of the
+ * atmel_mci driver.
+ */
+void __noreturn sam9263_atmci_start_image(u32 mmc_id, unsigned int clock,
+ bool slot_b)
+{
+ void __iomem *pio = IOMEM(AT91SAM9263_BASE_PIOA);
+ void *buf = (void *)AT91_CHIPSELECT_1;
+ void __iomem *base;
+ struct pbl_bio bio;
+ int ret;
+
+ at91_pmc_enable_periph_clock(IOMEM(AT91SAM926X_BASE_PMC), AT91SAM9263_ID_PIOA);
+
+ if (mmc_id == 0) {
+ base = IOMEM(AT91SAM9263_BASE_MCI0);
+
+ /* CLK */
+ at91_mux_pio_pin(pio, pin_to_mask(AT91_PIN_PA12), AT91_MUX_PERIPH_A, 0);
+
+ if (!slot_b) {
+ /* CMD */
+ at91_mux_pio_pin(pio, pin_to_mask(AT91_PIN_PA1), AT91_MUX_PERIPH_A, GPIO_PULL_UP);
+
+ /* DAT0 to DAT3 */
+ at91_mux_pio_pin(pio, pin_to_mask(AT91_PIN_PA0), AT91_MUX_PERIPH_A, GPIO_PULL_UP);
+ at91_mux_pio_pin(pio, pin_to_mask(AT91_PIN_PA3), AT91_MUX_PERIPH_A, GPIO_PULL_UP);
+ at91_mux_pio_pin(pio, pin_to_mask(AT91_PIN_PA4), AT91_MUX_PERIPH_A, GPIO_PULL_UP);
+ at91_mux_pio_pin(pio, pin_to_mask(AT91_PIN_PA5), AT91_MUX_PERIPH_A, GPIO_PULL_UP);
+ } else {
+ /* CMD */
+ at91_mux_pio_pin(pio, pin_to_mask(AT91_PIN_PA16), AT91_MUX_PERIPH_A, GPIO_PULL_UP);
+
+ /* DAT0 to DAT3 */
+ at91_mux_pio_pin(pio, pin_to_mask(AT91_PIN_PA17), AT91_MUX_PERIPH_A, GPIO_PULL_UP);
+ at91_mux_pio_pin(pio, pin_to_mask(AT91_PIN_PA18), AT91_MUX_PERIPH_A, GPIO_PULL_UP);
+ at91_mux_pio_pin(pio, pin_to_mask(AT91_PIN_PA19), AT91_MUX_PERIPH_A, GPIO_PULL_UP);
+ at91_mux_pio_pin(pio, pin_to_mask(AT91_PIN_PA20), AT91_MUX_PERIPH_A, GPIO_PULL_UP);
+ }
+
+ at91_pmc_enable_periph_clock(IOMEM(AT91SAM926X_BASE_PMC), AT91SAM9263_ID_MCI0);
+ } else {
+ base = IOMEM(AT91SAM9263_BASE_MCI1);
+
+ /* CLK */
+ at91_mux_pio_pin(pio, pin_to_mask(AT91_PIN_PA6), AT91_MUX_PERIPH_A, 0);
+
+ if (!slot_b) {
+ /* CMD */
+ at91_mux_pio_pin(pio, pin_to_mask(AT91_PIN_PA7), AT91_MUX_PERIPH_A, GPIO_PULL_UP);
+
+ /* DAT0 to DAT3 */
+ at91_mux_pio_pin(pio, pin_to_mask(AT91_PIN_PA8), AT91_MUX_PERIPH_A, GPIO_PULL_UP);
+ at91_mux_pio_pin(pio, pin_to_mask(AT91_PIN_PA9), AT91_MUX_PERIPH_A, GPIO_PULL_UP);
+ at91_mux_pio_pin(pio, pin_to_mask(AT91_PIN_PA10), AT91_MUX_PERIPH_A, GPIO_PULL_UP);
+ at91_mux_pio_pin(pio, pin_to_mask(AT91_PIN_PA11), AT91_MUX_PERIPH_A, GPIO_PULL_UP);
+ } else {
+ /* CMD */
+ at91_mux_pio_pin(pio, pin_to_mask(AT91_PIN_PA21), AT91_MUX_PERIPH_A, GPIO_PULL_UP);
+
+ /* DAT0 to DAT3 */
+ at91_mux_pio_pin(pio, pin_to_mask(AT91_PIN_PA22), AT91_MUX_PERIPH_A, GPIO_PULL_UP);
+ at91_mux_pio_pin(pio, pin_to_mask(AT91_PIN_PA23), AT91_MUX_PERIPH_A, GPIO_PULL_UP);
+ at91_mux_pio_pin(pio, pin_to_mask(AT91_PIN_PA24), AT91_MUX_PERIPH_A, GPIO_PULL_UP);
+ at91_mux_pio_pin(pio, pin_to_mask(AT91_PIN_PA25), AT91_MUX_PERIPH_A, GPIO_PULL_UP);
+ }
+
+ at91_pmc_enable_periph_clock(IOMEM(AT91SAM926X_BASE_PMC), AT91SAM9263_ID_MCI1);
+ }
+
+ ret = at91_mci_bio_init(&bio, base, clock, (int)slot_b);
+ if (ret) {
+ pr_err("atmci_start_image: bio init faild: %d\n", ret);
+ goto out_panic;
+ }
+
+ /* at91sam9x do not support high capacity */
+ at91_mci_bio_set_highcapacity(false);
+
+ ret = pbl_fat_load(&bio, "barebox.bin", buf, SZ_16M);
+ if (ret < 0) {
+ pr_err("pbl_fat_load: error %d\n", ret);
+ goto out_panic;
+ }
+
+ sync_caches_for_execution();
+
+ ((func)buf)(0, 0, NULL);
+
+out_panic:
+ panic("FAT chainloading failed\n");
+}
diff --git a/arch/arm/mach-at91/include/mach/xload.h b/arch/arm/mach-at91/include/mach/xload.h
index 488279c1a..82db65e30 100644
--- a/arch/arm/mach-at91/include/mach/xload.h
+++ b/arch/arm/mach-at91/include/mach/xload.h
@@ -15,4 +15,8 @@ int at91_mci_bio_init(struct pbl_bio *bio, void __iomem *base,
unsigned int clock, unsigned int slot);
void at91_mci_bio_set_highcapacity(bool highcapacity_card);
+void __noreturn sam9263_atmci_start_image(u32 mmc_id, unsigned int clock,
+ bool slot_b);
+
+
#endif /* __MACH_XLOAD_H */
--
2.34.1
More information about the barebox
mailing list