[PATCH v5 12/14] net: dsa: add KSZ9477 switch SPI driver
Ahmad Fatoum
a.fatoum at pengutronix.de
Sat Jul 30 02:10:34 PDT 2022
Hello Oleksij,
On 13.04.22 10:22, Oleksij Rempel wrote:
> +static int microchip_switch_probe(struct device_d *dev)
> +{
> + struct ksz_switch *priv;
> + int ret = 0, gpio;
> + struct dsa_switch *ds;
> +
> + priv = xzalloc(sizeof(*priv));
> +
> + dev->priv = priv;
> + priv->dev = dev;
> +
> + priv->spi = (struct spi_device *)dev->type_data;
> + priv->spi->mode = SPI_MODE_0;
The kernel DSA driver configures SPI_MODE_3.
Is it intended that you configure the barebox driver differently?
Cheers,
Ahmad
> + priv->spi->bits_per_word = 8;
> +
> + gpio = gpiod_get(dev, "reset", GPIOF_OUT_INIT_ACTIVE);
> + if (gpio_is_valid(gpio)) {
> + mdelay(1);
> + gpio_set_active(gpio, false);
> + }
> +
> + ksz_reset_switch(dev->priv);
> +
> + ret = ksz9477_switch_detect(dev->priv);
> + if (ret) {
> + dev_err(&priv->spi->dev, "error detecting KSZ9477: %s\n",
> + strerror(-ret));
> + return -ENODEV;
> + }
> +
> + dev_info(dev, "chip id: 0x%08x\n", priv->chip_id);
> +
> + ds = &priv->ds;
> + ds->dev = dev;
> + ds->num_ports = 7;
> + ds->ops = &ksz_dsa_ops;
> + ds->needed_rx_tailroom = 1;
> + ds->needed_tx_tailroom = 2;
> + if (priv->phy_port_cnt == 5)
> + ds->phys_mii_mask = 0x1f;
> + else
> + ds->phys_mii_mask = 0x03;
> +
> + ksz_default_setup(priv);
> +
> + return dsa_register_switch(ds);
> +}
> +
> +static const struct of_device_id microchip_switch_dt_ids[] = {
> + { .compatible = "microchip,ksz9477" },
> + { .compatible = "microchip,ksz9563" },
> + { }
> +};
> +
> +static struct driver_d microchip_switch_driver = {
> + .name = "ksz9477",
> + .probe = microchip_switch_probe,
> + .of_compatible = DRV_OF_COMPAT(microchip_switch_dt_ids),
> +};
> +
> +device_spi_driver(microchip_switch_driver);
> diff --git a/include/platform_data/ksz9477_reg.h b/include/platform_data/ksz9477_reg.h
> new file mode 100644
> index 0000000000..2938e892b6
> --- /dev/null
> +++ b/include/platform_data/ksz9477_reg.h
> @@ -0,0 +1,1665 @@
> +/* SPDX-License-Identifier: GPL-2.0
> + *
> + * Microchip KSZ9477 register definitions
> + *
> + * Copyright (C) 2017-2018 Microchip Technology Inc.
> + */
> +
> +#ifndef __KSZ9477_REGS_H
> +#define __KSZ9477_REGS_H
> +
> +#define KS_PRIO_M 0x7
> +#define KS_PRIO_S 4
> +
> +/* 0 - Operation */
> +#define REG_CHIP_ID0__1 0x0000
> +
> +#define REG_CHIP_ID1__1 0x0001
> +
> +#define FAMILY_ID 0x95
> +#define FAMILY_ID_94 0x94
> +#define FAMILY_ID_95 0x95
> +#define FAMILY_ID_85 0x85
> +#define FAMILY_ID_98 0x98
> +#define FAMILY_ID_88 0x88
> +
> +#define REG_CHIP_ID2__1 0x0002
> +
> +#define CHIP_ID_63 0x63
> +#define CHIP_ID_66 0x66
> +#define CHIP_ID_67 0x67
> +#define CHIP_ID_77 0x77
> +#define CHIP_ID_93 0x93
> +#define CHIP_ID_96 0x96
> +#define CHIP_ID_97 0x97
> +
> +#define REG_CHIP_ID3__1 0x0003
> +
> +#define SWITCH_REVISION_M 0x0F
> +#define SWITCH_REVISION_S 4
> +#define SWITCH_RESET 0x01
> +
> +#define REG_SW_PME_CTRL 0x0006
> +
> +#define PME_ENABLE BIT(1)
> +#define PME_POLARITY BIT(0)
> +
> +#define REG_GLOBAL_OPTIONS 0x000F
> +
> +#define SW_GIGABIT_ABLE BIT(6)
> +#define SW_REDUNDANCY_ABLE BIT(5)
> +#define SW_AVB_ABLE BIT(4)
> +#define SW_9567_RL_5_2 0xC
> +#define SW_9477_SL_5_2 0xD
> +
> +#define SW_9896_GL_5_1 0xB
> +#define SW_9896_RL_5_1 0x8
> +#define SW_9896_SL_5_1 0x9
> +
> +#define SW_9895_GL_4_1 0x7
> +#define SW_9895_RL_4_1 0x4
> +#define SW_9895_SL_4_1 0x5
> +
> +#define SW_9896_RL_4_2 0x6
> +
> +#define SW_9893_RL_2_1 0x0
> +#define SW_9893_SL_2_1 0x1
> +#define SW_9893_GL_2_1 0x3
> +
> +#define SW_QW_ABLE BIT(5)
> +#define SW_9893_RN_2_1 0xC
> +
> +#define REG_SW_INT_STATUS__4 0x0010
> +#define REG_SW_INT_MASK__4 0x0014
> +
> +#define LUE_INT BIT(31)
> +#define TRIG_TS_INT BIT(30)
> +#define APB_TIMEOUT_INT BIT(29)
> +
> +#define SWITCH_INT_MASK (TRIG_TS_INT | APB_TIMEOUT_INT)
> +
> +#define REG_SW_PORT_INT_STATUS__4 0x0018
> +#define REG_SW_PORT_INT_MASK__4 0x001C
> +#define REG_SW_PHY_INT_STATUS 0x0020
> +#define REG_SW_PHY_INT_ENABLE 0x0024
> +
> +/* 1 - Global */
> +#define REG_SW_GLOBAL_SERIAL_CTRL_0 0x0100
> +#define SW_SPARE_REG_2 BIT(7)
> +#define SW_SPARE_REG_1 BIT(6)
> +#define SW_SPARE_REG_0 BIT(5)
> +#define SW_BIG_ENDIAN BIT(4)
> +#define SPI_AUTO_EDGE_DETECTION BIT(1)
> +#define SPI_CLOCK_OUT_RISING_EDGE BIT(0)
> +
> +#define REG_SW_GLOBAL_OUTPUT_CTRL__1 0x0103
> +#define SW_ENABLE_REFCLKO BIT(1)
> +#define SW_REFCLKO_IS_125MHZ BIT(0)
> +
> +#define REG_SW_IBA__4 0x0104
> +
> +#define SW_IBA_ENABLE BIT(31)
> +#define SW_IBA_DA_MATCH BIT(30)
> +#define SW_IBA_INIT BIT(29)
> +#define SW_IBA_QID_M 0xF
> +#define SW_IBA_QID_S 22
> +#define SW_IBA_PORT_M 0x2F
> +#define SW_IBA_PORT_S 16
> +#define SW_IBA_FRAME_TPID_M 0xFFFF
> +
> +#define REG_SW_APB_TIMEOUT_ADDR__4 0x0108
> +
> +#define APB_TIMEOUT_ACKNOWLEDGE BIT(31)
> +
> +#define REG_SW_IBA_SYNC__1 0x010C
> +
> +#define REG_SW_IO_STRENGTH__1 0x010D
> +#define SW_DRIVE_STRENGTH_M 0x7
> +#define SW_DRIVE_STRENGTH_2MA 0
> +#define SW_DRIVE_STRENGTH_4MA 1
> +#define SW_DRIVE_STRENGTH_8MA 2
> +#define SW_DRIVE_STRENGTH_12MA 3
> +#define SW_DRIVE_STRENGTH_16MA 4
> +#define SW_DRIVE_STRENGTH_20MA 5
> +#define SW_DRIVE_STRENGTH_24MA 6
> +#define SW_DRIVE_STRENGTH_28MA 7
> +#define SW_HI_SPEED_DRIVE_STRENGTH_S 4
> +#define SW_LO_SPEED_DRIVE_STRENGTH_S 0
> +
> +#define REG_SW_IBA_STATUS__4 0x0110
> +
> +#define SW_IBA_REQ BIT(31)
> +#define SW_IBA_RESP BIT(30)
> +#define SW_IBA_DA_MISMATCH BIT(14)
> +#define SW_IBA_FMT_MISMATCH BIT(13)
> +#define SW_IBA_CODE_ERROR BIT(12)
> +#define SW_IBA_CMD_ERROR BIT(11)
> +#define SW_IBA_CMD_LOC_M (BIT(6) - 1)
> +
> +#define REG_SW_IBA_STATES__4 0x0114
> +
> +#define SW_IBA_BUF_STATE_S 30
> +#define SW_IBA_CMD_STATE_S 28
> +#define SW_IBA_RESP_STATE_S 26
> +#define SW_IBA_STATE_M 0x3
> +#define SW_IBA_PACKET_SIZE_M 0x7F
> +#define SW_IBA_PACKET_SIZE_S 16
> +#define SW_IBA_FMT_ID_M 0xFFFF
> +
> +#define REG_SW_IBA_RESULT__4 0x0118
> +
> +#define SW_IBA_SIZE_S 24
> +
> +#define SW_IBA_RETRY_CNT_M (BIT(5) - 1)
> +
> +/* 2 - PHY */
> +#define REG_SW_POWER_MANAGEMENT_CTRL 0x0201
> +
> +#define SW_PLL_POWER_DOWN BIT(5)
> +#define SW_POWER_DOWN_MODE 0x3
> +#define SW_ENERGY_DETECTION 1
> +#define SW_SOFT_POWER_DOWN 2
> +#define SW_POWER_SAVING 3
> +
> +/* 3 - Operation Control */
> +#define REG_SW_OPERATION 0x0300
> +
> +#define SW_DOUBLE_TAG BIT(7)
> +#define SW_RESET BIT(1)
> +#define SW_START BIT(0)
> +
> +#define REG_SW_MAC_ADDR_0 0x0302
> +#define REG_SW_MAC_ADDR_1 0x0303
> +#define REG_SW_MAC_ADDR_2 0x0304
> +#define REG_SW_MAC_ADDR_3 0x0305
> +#define REG_SW_MAC_ADDR_4 0x0306
> +#define REG_SW_MAC_ADDR_5 0x0307
> +
> +#define REG_SW_MTU__2 0x0308
> +
> +#define REG_SW_ISP_TPID__2 0x030A
> +
> +#define REG_SW_HSR_TPID__2 0x030C
> +
> +#define REG_AVB_STRATEGY__2 0x030E
> +
> +#define SW_SHAPING_CREDIT_ACCT BIT(1)
> +#define SW_POLICING_CREDIT_ACCT BIT(0)
> +
> +#define REG_SW_LUE_CTRL_0 0x0310
> +
> +#define SW_VLAN_ENABLE BIT(7)
> +#define SW_DROP_INVALID_VID BIT(6)
> +#define SW_AGE_CNT_M 0x7
> +#define SW_AGE_CNT_S 3
> +#define SW_RESV_MCAST_ENABLE BIT(2)
> +#define SW_HASH_OPTION_M 0x03
> +#define SW_HASH_OPTION_CRC 1
> +#define SW_HASH_OPTION_XOR 2
> +#define SW_HASH_OPTION_DIRECT 3
> +
> +#define REG_SW_LUE_CTRL_1 0x0311
> +
> +#define UNICAST_LEARN_DISABLE BIT(7)
> +#define SW_SRC_ADDR_FILTER BIT(6)
> +#define SW_FLUSH_STP_TABLE BIT(5)
> +#define SW_FLUSH_MSTP_TABLE BIT(4)
> +#define SW_FWD_MCAST_SRC_ADDR BIT(3)
> +#define SW_AGING_ENABLE BIT(2)
> +#define SW_FAST_AGING BIT(1)
> +#define SW_LINK_AUTO_AGING BIT(0)
> +
> +#define REG_SW_LUE_CTRL_2 0x0312
> +
> +#define SW_TRAP_DOUBLE_TAG BIT(6)
> +#define SW_EGRESS_VLAN_FILTER_DYN BIT(5)
> +#define SW_EGRESS_VLAN_FILTER_STA BIT(4)
> +#define SW_FLUSH_OPTION_M 0x3
> +#define SW_FLUSH_OPTION_S 2
> +#define SW_FLUSH_OPTION_DYN_MAC 1
> +#define SW_FLUSH_OPTION_STA_MAC 2
> +#define SW_FLUSH_OPTION_BOTH 3
> +#define SW_PRIO_M 0x3
> +#define SW_PRIO_DA 0
> +#define SW_PRIO_SA 1
> +#define SW_PRIO_HIGHEST_DA_SA 2
> +#define SW_PRIO_LOWEST_DA_SA 3
> +
> +#define REG_SW_LUE_CTRL_3 0x0313
> +
> +#define REG_SW_LUE_INT_STATUS 0x0314
> +#define REG_SW_LUE_INT_ENABLE 0x0315
> +
> +#define LEARN_FAIL_INT BIT(2)
> +#define ALMOST_FULL_INT BIT(1)
> +#define WRITE_FAIL_INT BIT(0)
> +
> +#define REG_SW_LUE_INDEX_0__2 0x0316
> +
> +#define ENTRY_INDEX_M 0x0FFF
> +
> +#define REG_SW_LUE_INDEX_1__2 0x0318
> +
> +#define FAIL_INDEX_M 0x03FF
> +
> +#define REG_SW_LUE_INDEX_2__2 0x031A
> +
> +#define REG_SW_LUE_UNK_UCAST_CTRL__4 0x0320
> +
> +#define SW_UNK_UCAST_ENABLE BIT(31)
> +
> +#define REG_SW_LUE_UNK_MCAST_CTRL__4 0x0324
> +
> +#define SW_UNK_MCAST_ENABLE BIT(31)
> +
> +#define REG_SW_LUE_UNK_VID_CTRL__4 0x0328
> +
> +#define SW_UNK_VID_ENABLE BIT(31)
> +
> +#define REG_SW_MAC_CTRL_0 0x0330
> +
> +#define SW_NEW_BACKOFF BIT(7)
> +#define SW_CHECK_LENGTH BIT(3)
> +#define SW_PAUSE_UNH_MODE BIT(1)
> +#define SW_AGGR_BACKOFF BIT(0)
> +
> +#define REG_SW_MAC_CTRL_1 0x0331
> +
> +#define MULTICAST_STORM_DISABLE BIT(6)
> +#define SW_BACK_PRESSURE BIT(5)
> +#define FAIR_FLOW_CTRL BIT(4)
> +#define NO_EXC_COLLISION_DROP BIT(3)
> +#define SW_JUMBO_PACKET BIT(2)
> +#define SW_LEGAL_PACKET_DISABLE BIT(1)
> +#define SW_PASS_SHORT_FRAME BIT(0)
> +
> +#define REG_SW_MAC_CTRL_2 0x0332
> +
> +#define SW_REPLACE_VID BIT(3)
> +#define BROADCAST_STORM_RATE_HI 0x07
> +
> +#define REG_SW_MAC_CTRL_3 0x0333
> +
> +#define BROADCAST_STORM_RATE_LO 0xFF
> +#define BROADCAST_STORM_RATE 0x07FF
> +
> +#define REG_SW_MAC_CTRL_4 0x0334
> +
> +#define SW_PASS_PAUSE BIT(3)
> +
> +#define REG_SW_MAC_CTRL_5 0x0335
> +
> +#define SW_OUT_RATE_LIMIT_QUEUE_BASED BIT(3)
> +
> +#define REG_SW_MAC_CTRL_6 0x0336
> +
> +#define SW_MIB_COUNTER_FLUSH BIT(7)
> +#define SW_MIB_COUNTER_FREEZE BIT(6)
> +
> +#define REG_SW_MAC_802_1P_MAP_0 0x0338
> +#define REG_SW_MAC_802_1P_MAP_1 0x0339
> +#define REG_SW_MAC_802_1P_MAP_2 0x033A
> +#define REG_SW_MAC_802_1P_MAP_3 0x033B
> +
> +#define SW_802_1P_MAP_M KS_PRIO_M
> +#define SW_802_1P_MAP_S KS_PRIO_S
> +
> +#define REG_SW_MAC_ISP_CTRL 0x033C
> +
> +#define REG_SW_MAC_TOS_CTRL 0x033E
> +
> +#define SW_TOS_DSCP_REMARK BIT(1)
> +#define SW_TOS_DSCP_REMAP BIT(0)
> +
> +#define REG_SW_MAC_TOS_PRIO_0 0x0340
> +#define REG_SW_MAC_TOS_PRIO_1 0x0341
> +#define REG_SW_MAC_TOS_PRIO_2 0x0342
> +#define REG_SW_MAC_TOS_PRIO_3 0x0343
> +#define REG_SW_MAC_TOS_PRIO_4 0x0344
> +#define REG_SW_MAC_TOS_PRIO_5 0x0345
> +#define REG_SW_MAC_TOS_PRIO_6 0x0346
> +#define REG_SW_MAC_TOS_PRIO_7 0x0347
> +#define REG_SW_MAC_TOS_PRIO_8 0x0348
> +#define REG_SW_MAC_TOS_PRIO_9 0x0349
> +#define REG_SW_MAC_TOS_PRIO_10 0x034A
> +#define REG_SW_MAC_TOS_PRIO_11 0x034B
> +#define REG_SW_MAC_TOS_PRIO_12 0x034C
> +#define REG_SW_MAC_TOS_PRIO_13 0x034D
> +#define REG_SW_MAC_TOS_PRIO_14 0x034E
> +#define REG_SW_MAC_TOS_PRIO_15 0x034F
> +#define REG_SW_MAC_TOS_PRIO_16 0x0350
> +#define REG_SW_MAC_TOS_PRIO_17 0x0351
> +#define REG_SW_MAC_TOS_PRIO_18 0x0352
> +#define REG_SW_MAC_TOS_PRIO_19 0x0353
> +#define REG_SW_MAC_TOS_PRIO_20 0x0354
> +#define REG_SW_MAC_TOS_PRIO_21 0x0355
> +#define REG_SW_MAC_TOS_PRIO_22 0x0356
> +#define REG_SW_MAC_TOS_PRIO_23 0x0357
> +#define REG_SW_MAC_TOS_PRIO_24 0x0358
> +#define REG_SW_MAC_TOS_PRIO_25 0x0359
> +#define REG_SW_MAC_TOS_PRIO_26 0x035A
> +#define REG_SW_MAC_TOS_PRIO_27 0x035B
> +#define REG_SW_MAC_TOS_PRIO_28 0x035C
> +#define REG_SW_MAC_TOS_PRIO_29 0x035D
> +#define REG_SW_MAC_TOS_PRIO_30 0x035E
> +#define REG_SW_MAC_TOS_PRIO_31 0x035F
> +
> +#define REG_SW_MRI_CTRL_0 0x0370
> +
> +#define SW_IGMP_SNOOP BIT(6)
> +#define SW_IPV6_MLD_OPTION BIT(3)
> +#define SW_IPV6_MLD_SNOOP BIT(2)
> +#define SW_MIRROR_RX_TX BIT(0)
> +
> +#define REG_SW_CLASS_D_IP_CTRL__4 0x0374
> +
> +#define SW_CLASS_D_IP_ENABLE BIT(31)
> +
> +#define REG_SW_MRI_CTRL_8 0x0378
> +
> +#define SW_NO_COLOR_S 6
> +#define SW_RED_COLOR_S 4
> +#define SW_YELLOW_COLOR_S 2
> +#define SW_GREEN_COLOR_S 0
> +#define SW_COLOR_M 0x3
> +
> +#define REG_SW_QM_CTRL__4 0x0390
> +
> +#define PRIO_SCHEME_SELECT_M KS_PRIO_M
> +#define PRIO_SCHEME_SELECT_S 6
> +#define PRIO_MAP_3_HI 0
> +#define PRIO_MAP_2_HI 2
> +#define PRIO_MAP_0_LO 3
> +#define UNICAST_VLAN_BOUNDARY BIT(1)
> +
> +#define REG_SW_EEE_QM_CTRL__2 0x03C0
> +
> +#define REG_SW_EEE_TXQ_WAIT_TIME__2 0x03C2
> +
> +/* 4 - */
> +#define REG_SW_VLAN_ENTRY__4 0x0400
> +
> +#define VLAN_VALID BIT(31)
> +#define VLAN_FORWARD_OPTION BIT(27)
> +#define VLAN_PRIO_M KS_PRIO_M
> +#define VLAN_PRIO_S 24
> +#define VLAN_MSTP_M 0x7
> +#define VLAN_MSTP_S 12
> +#define VLAN_FID_M 0x7F
> +
> +#define REG_SW_VLAN_ENTRY_UNTAG__4 0x0404
> +#define REG_SW_VLAN_ENTRY_PORTS__4 0x0408
> +
> +#define REG_SW_VLAN_ENTRY_INDEX__2 0x040C
> +
> +#define VLAN_INDEX_M 0x0FFF
> +
> +#define REG_SW_VLAN_CTRL 0x040E
> +
> +#define VLAN_START BIT(7)
> +#define VLAN_ACTION 0x3
> +#define VLAN_WRITE 1
> +#define VLAN_READ 2
> +#define VLAN_CLEAR 3
> +
> +#define REG_SW_ALU_INDEX_0 0x0410
> +
> +#define ALU_FID_INDEX_S 16
> +#define ALU_MAC_ADDR_HI 0xFFFF
> +
> +#define REG_SW_ALU_INDEX_1 0x0414
> +
> +#define ALU_DIRECT_INDEX_M (BIT(12) - 1)
> +
> +#define REG_SW_ALU_CTRL__4 0x0418
> +
> +#define ALU_VALID_CNT_M (BIT(14) - 1)
> +#define ALU_VALID_CNT_S 16
> +#define ALU_START BIT(7)
> +#define ALU_VALID BIT(6)
> +#define ALU_DIRECT BIT(2)
> +#define ALU_ACTION 0x3
> +#define ALU_WRITE 1
> +#define ALU_READ 2
> +#define ALU_SEARCH 3
> +
> +#define REG_SW_ALU_STAT_CTRL__4 0x041C
> +
> +#define ALU_STAT_INDEX_M (BIT(4) - 1)
> +#define ALU_STAT_INDEX_S 16
> +#define ALU_RESV_MCAST_INDEX_M (BIT(6) - 1)
> +#define ALU_STAT_START BIT(7)
> +#define ALU_RESV_MCAST_ADDR BIT(1)
> +#define ALU_STAT_READ BIT(0)
> +
> +#define REG_SW_ALU_VAL_A 0x0420
> +
> +#define ALU_V_STATIC_VALID BIT(31)
> +#define ALU_V_SRC_FILTER BIT(30)
> +#define ALU_V_DST_FILTER BIT(29)
> +#define ALU_V_PRIO_AGE_CNT_M (BIT(3) - 1)
> +#define ALU_V_PRIO_AGE_CNT_S 26
> +#define ALU_V_MSTP_M 0x7
> +
> +#define REG_SW_ALU_VAL_B 0x0424
> +
> +#define ALU_V_OVERRIDE BIT(31)
> +#define ALU_V_USE_FID BIT(30)
> +#define ALU_V_PORT_MAP (BIT(24) - 1)
> +
> +#define REG_SW_ALU_VAL_C 0x0428
> +
> +#define ALU_V_FID_M (BIT(16) - 1)
> +#define ALU_V_FID_S 16
> +#define ALU_V_MAC_ADDR_HI 0xFFFF
> +
> +#define REG_SW_ALU_VAL_D 0x042C
> +
> +#define REG_HSR_ALU_INDEX_0 0x0440
> +
> +#define REG_HSR_ALU_INDEX_1 0x0444
> +
> +#define HSR_DST_MAC_INDEX_LO_S 16
> +#define HSR_SRC_MAC_INDEX_HI 0xFFFF
> +
> +#define REG_HSR_ALU_INDEX_2 0x0448
> +
> +#define HSR_INDEX_MAX BIT(9)
> +#define HSR_DIRECT_INDEX_M (HSR_INDEX_MAX - 1)
> +
> +#define REG_HSR_ALU_INDEX_3 0x044C
> +
> +#define HSR_PATH_INDEX_M (BIT(4) - 1)
> +
> +#define REG_HSR_ALU_CTRL__4 0x0450
> +
> +#define HSR_VALID_CNT_M (BIT(14) - 1)
> +#define HSR_VALID_CNT_S 16
> +#define HSR_START BIT(7)
> +#define HSR_VALID BIT(6)
> +#define HSR_SEARCH_END BIT(5)
> +#define HSR_DIRECT BIT(2)
> +#define HSR_ACTION 0x3
> +#define HSR_WRITE 1
> +#define HSR_READ 2
> +#define HSR_SEARCH 3
> +
> +#define REG_HSR_ALU_VAL_A 0x0454
> +
> +#define HSR_V_STATIC_VALID BIT(31)
> +#define HSR_V_AGE_CNT_M (BIT(3) - 1)
> +#define HSR_V_AGE_CNT_S 26
> +#define HSR_V_PATH_ID_M (BIT(4) - 1)
> +
> +#define REG_HSR_ALU_VAL_B 0x0458
> +
> +#define REG_HSR_ALU_VAL_C 0x045C
> +
> +#define HSR_V_DST_MAC_ADDR_LO_S 16
> +#define HSR_V_SRC_MAC_ADDR_HI 0xFFFF
> +
> +#define REG_HSR_ALU_VAL_D 0x0460
> +
> +#define REG_HSR_ALU_VAL_E 0x0464
> +
> +#define HSR_V_START_SEQ_1_S 16
> +#define HSR_V_START_SEQ_2_S 0
> +
> +#define REG_HSR_ALU_VAL_F 0x0468
> +
> +#define HSR_V_EXP_SEQ_1_S 16
> +#define HSR_V_EXP_SEQ_2_S 0
> +
> +#define REG_HSR_ALU_VAL_G 0x046C
> +
> +#define HSR_V_SEQ_CNT_1_S 16
> +#define HSR_V_SEQ_CNT_2_S 0
> +
> +#define HSR_V_SEQ_M (BIT(16) - 1)
> +
> +/* 5 - PTP Clock */
> +#define REG_PTP_CLK_CTRL 0x0500
> +
> +#define PTP_STEP_ADJ BIT(6)
> +#define PTP_STEP_DIR BIT(5)
> +#define PTP_READ_TIME BIT(4)
> +#define PTP_LOAD_TIME BIT(3)
> +#define PTP_CLK_ADJ_ENABLE BIT(2)
> +#define PTP_CLK_ENABLE BIT(1)
> +#define PTP_CLK_RESET BIT(0)
> +
> +#define REG_PTP_RTC_SUB_NANOSEC__2 0x0502
> +
> +#define PTP_RTC_SUB_NANOSEC_M 0x0007
> +
> +#define REG_PTP_RTC_NANOSEC 0x0504
> +#define REG_PTP_RTC_NANOSEC_H 0x0504
> +#define REG_PTP_RTC_NANOSEC_L 0x0506
> +
> +#define REG_PTP_RTC_SEC 0x0508
> +#define REG_PTP_RTC_SEC_H 0x0508
> +#define REG_PTP_RTC_SEC_L 0x050A
> +
> +#define REG_PTP_SUBNANOSEC_RATE 0x050C
> +#define REG_PTP_SUBNANOSEC_RATE_H 0x050C
> +
> +#define PTP_RATE_DIR BIT(31)
> +#define PTP_TMP_RATE_ENABLE BIT(30)
> +
> +#define REG_PTP_SUBNANOSEC_RATE_L 0x050E
> +
> +#define REG_PTP_RATE_DURATION 0x0510
> +#define REG_PTP_RATE_DURATION_H 0x0510
> +#define REG_PTP_RATE_DURATION_L 0x0512
> +
> +#define REG_PTP_MSG_CONF1 0x0514
> +
> +#define PTP_802_1AS BIT(7)
> +#define PTP_ENABLE BIT(6)
> +#define PTP_ETH_ENABLE BIT(5)
> +#define PTP_IPV4_UDP_ENABLE BIT(4)
> +#define PTP_IPV6_UDP_ENABLE BIT(3)
> +#define PTP_TC_P2P BIT(2)
> +#define PTP_MASTER BIT(1)
> +#define PTP_1STEP BIT(0)
> +
> +#define REG_PTP_MSG_CONF2 0x0516
> +
> +#define PTP_UNICAST_ENABLE BIT(12)
> +#define PTP_ALTERNATE_MASTER BIT(11)
> +#define PTP_ALL_HIGH_PRIO BIT(10)
> +#define PTP_SYNC_CHECK BIT(9)
> +#define PTP_DELAY_CHECK BIT(8)
> +#define PTP_PDELAY_CHECK BIT(7)
> +#define PTP_DROP_SYNC_DELAY_REQ BIT(5)
> +#define PTP_DOMAIN_CHECK BIT(4)
> +#define PTP_UDP_CHECKSUM BIT(2)
> +
> +#define REG_PTP_DOMAIN_VERSION 0x0518
> +#define PTP_VERSION_M 0xFF00
> +#define PTP_DOMAIN_M 0x00FF
> +
> +#define REG_PTP_UNIT_INDEX__4 0x0520
> +
> +#define PTP_UNIT_M 0xF
> +
> +#define PTP_GPIO_INDEX_S 16
> +#define PTP_TSI_INDEX_S 8
> +#define PTP_TOU_INDEX_S 0
> +
> +#define REG_PTP_TRIG_STATUS__4 0x0524
> +
> +#define TRIG_ERROR_S 16
> +#define TRIG_DONE_S 0
> +
> +#define REG_PTP_INT_STATUS__4 0x0528
> +
> +#define TRIG_INT_S 16
> +#define TS_INT_S 0
> +
> +#define TRIG_UNIT_M 0x7
> +#define TS_UNIT_M 0x3
> +
> +#define REG_PTP_CTRL_STAT__4 0x052C
> +
> +#define GPIO_IN BIT(7)
> +#define GPIO_OUT BIT(6)
> +#define TS_INT_ENABLE BIT(5)
> +#define TRIG_ACTIVE BIT(4)
> +#define TRIG_ENABLE BIT(3)
> +#define TRIG_RESET BIT(2)
> +#define TS_ENABLE BIT(1)
> +#define TS_RESET BIT(0)
> +
> +#define GPIO_CTRL_M (GPIO_IN | GPIO_OUT)
> +
> +#define TRIG_CTRL_M \
> + (TRIG_ACTIVE | TRIG_ENABLE | TRIG_RESET)
> +
> +#define TS_CTRL_M \
> + (TS_INT_ENABLE | TS_ENABLE | TS_RESET)
> +
> +#define REG_TRIG_TARGET_NANOSEC 0x0530
> +#define REG_TRIG_TARGET_SEC 0x0534
> +
> +#define REG_TRIG_CTRL__4 0x0538
> +
> +#define TRIG_CASCADE_ENABLE BIT(31)
> +#define TRIG_CASCADE_TAIL BIT(30)
> +#define TRIG_CASCADE_UPS_M 0xF
> +#define TRIG_CASCADE_UPS_S 26
> +#define TRIG_NOW BIT(25)
> +#define TRIG_NOTIFY BIT(24)
> +#define TRIG_EDGE BIT(23)
> +#define TRIG_PATTERN_S 20
> +#define TRIG_PATTERN_M 0x7
> +#define TRIG_NEG_EDGE 0
> +#define TRIG_POS_EDGE 1
> +#define TRIG_NEG_PULSE 2
> +#define TRIG_POS_PULSE 3
> +#define TRIG_NEG_PERIOD 4
> +#define TRIG_POS_PERIOD 5
> +#define TRIG_REG_OUTPUT 6
> +#define TRIG_GPO_S 16
> +#define TRIG_GPO_M 0xF
> +#define TRIG_CASCADE_ITERATE_CNT_M 0xFFFF
> +
> +#define REG_TRIG_CYCLE_WIDTH 0x053C
> +
> +#define REG_TRIG_CYCLE_CNT 0x0540
> +
> +#define TRIG_CYCLE_CNT_M 0xFFFF
> +#define TRIG_CYCLE_CNT_S 16
> +#define TRIG_BIT_PATTERN_M 0xFFFF
> +
> +#define REG_TRIG_ITERATE_TIME 0x0544
> +
> +#define REG_TRIG_PULSE_WIDTH__4 0x0548
> +
> +#define TRIG_PULSE_WIDTH_M 0x00FFFFFF
> +
> +#define REG_TS_CTRL_STAT__4 0x0550
> +
> +#define TS_EVENT_DETECT_M 0xF
> +#define TS_EVENT_DETECT_S 17
> +#define TS_EVENT_OVERFLOW BIT(16)
> +#define TS_GPI_M 0xF
> +#define TS_GPI_S 8
> +#define TS_DETECT_RISE BIT(7)
> +#define TS_DETECT_FALL BIT(6)
> +#define TS_DETECT_S 6
> +#define TS_CASCADE_TAIL BIT(5)
> +#define TS_CASCADE_UPS_M 0xF
> +#define TS_CASCADE_UPS_S 1
> +#define TS_CASCADE_ENABLE BIT(0)
> +
> +#define DETECT_RISE (TS_DETECT_RISE >> TS_DETECT_S)
> +#define DETECT_FALL (TS_DETECT_FALL >> TS_DETECT_S)
> +
> +#define REG_TS_EVENT_0_NANOSEC 0x0554
> +#define REG_TS_EVENT_0_SEC 0x0558
> +#define REG_TS_EVENT_0_SUB_NANOSEC 0x055C
> +
> +#define REG_TS_EVENT_1_NANOSEC 0x0560
> +#define REG_TS_EVENT_1_SEC 0x0564
> +#define REG_TS_EVENT_1_SUB_NANOSEC 0x0568
> +
> +#define REG_TS_EVENT_2_NANOSEC 0x056C
> +#define REG_TS_EVENT_2_SEC 0x0570
> +#define REG_TS_EVENT_2_SUB_NANOSEC 0x0574
> +
> +#define REG_TS_EVENT_3_NANOSEC 0x0578
> +#define REG_TS_EVENT_3_SEC 0x057C
> +#define REG_TS_EVENT_3_SUB_NANOSEC 0x0580
> +
> +#define REG_TS_EVENT_4_NANOSEC 0x0584
> +#define REG_TS_EVENT_4_SEC 0x0588
> +#define REG_TS_EVENT_4_SUB_NANOSEC 0x058C
> +
> +#define REG_TS_EVENT_5_NANOSEC 0x0590
> +#define REG_TS_EVENT_5_SEC 0x0594
> +#define REG_TS_EVENT_5_SUB_NANOSEC 0x0598
> +
> +#define REG_TS_EVENT_6_NANOSEC 0x059C
> +#define REG_TS_EVENT_6_SEC 0x05A0
> +#define REG_TS_EVENT_6_SUB_NANOSEC 0x05A4
> +
> +#define REG_TS_EVENT_7_NANOSEC 0x05A8
> +#define REG_TS_EVENT_7_SEC 0x05AC
> +#define REG_TS_EVENT_7_SUB_NANOSEC 0x05B0
> +
> +#define TS_EVENT_EDGE_M 0x1
> +#define TS_EVENT_EDGE_S 30
> +#define TS_EVENT_NANOSEC_M (BIT(30) - 1)
> +
> +#define TS_EVENT_SUB_NANOSEC_M 0x7
> +
> +#define TS_EVENT_SAMPLE \
> + (REG_TS_EVENT_1_NANOSEC - REG_TS_EVENT_0_NANOSEC)
> +
> +#define PORT_CTRL_ADDR(port, addr) ((addr) | (((port) + 1) << 12))
> +
> +#define REG_GLOBAL_RR_INDEX__1 0x0600
> +
> +/* DLR */
> +#define REG_DLR_SRC_PORT__4 0x0604
> +
> +#define DLR_SRC_PORT_UNICAST BIT(31)
> +#define DLR_SRC_PORT_M 0x3
> +#define DLR_SRC_PORT_BOTH 0
> +#define DLR_SRC_PORT_EACH 1
> +
> +#define REG_DLR_IP_ADDR__4 0x0608
> +
> +#define REG_DLR_CTRL__1 0x0610
> +
> +#define DLR_RESET_SEQ_ID BIT(3)
> +#define DLR_BACKUP_AUTO_ON BIT(2)
> +#define DLR_BEACON_TX_ENABLE BIT(1)
> +#define DLR_ASSIST_ENABLE BIT(0)
> +
> +#define REG_DLR_STATE__1 0x0611
> +
> +#define DLR_NODE_STATE_M 0x3
> +#define DLR_NODE_STATE_S 1
> +#define DLR_NODE_STATE_IDLE 0
> +#define DLR_NODE_STATE_FAULT 1
> +#define DLR_NODE_STATE_NORMAL 2
> +#define DLR_RING_STATE_FAULT 0
> +#define DLR_RING_STATE_NORMAL 1
> +
> +#define REG_DLR_PRECEDENCE__1 0x0612
> +
> +#define REG_DLR_BEACON_INTERVAL__4 0x0614
> +
> +#define REG_DLR_BEACON_TIMEOUT__4 0x0618
> +
> +#define REG_DLR_TIMEOUT_WINDOW__4 0x061C
> +
> +#define DLR_TIMEOUT_WINDOW_M (BIT(22) - 1)
> +
> +#define REG_DLR_VLAN_ID__2 0x0620
> +
> +#define DLR_VLAN_ID_M (BIT(12) - 1)
> +
> +#define REG_DLR_DEST_ADDR_0 0x0622
> +#define REG_DLR_DEST_ADDR_1 0x0623
> +#define REG_DLR_DEST_ADDR_2 0x0624
> +#define REG_DLR_DEST_ADDR_3 0x0625
> +#define REG_DLR_DEST_ADDR_4 0x0626
> +#define REG_DLR_DEST_ADDR_5 0x0627
> +
> +#define REG_DLR_PORT_MAP__4 0x0628
> +
> +#define REG_DLR_CLASS__1 0x062C
> +
> +#define DLR_FRAME_QID_M 0x3
> +
> +/* HSR */
> +#define REG_HSR_PORT_MAP__4 0x0640
> +
> +#define REG_HSR_ALU_CTRL_0__1 0x0644
> +
> +#define HSR_DUPLICATE_DISCARD BIT(7)
> +#define HSR_NODE_UNICAST BIT(6)
> +#define HSR_AGE_CNT_DEFAULT_M 0x7
> +#define HSR_AGE_CNT_DEFAULT_S 3
> +#define HSR_LEARN_MCAST_DISABLE BIT(2)
> +#define HSR_HASH_OPTION_M 0x3
> +#define HSR_HASH_DISABLE 0
> +#define HSR_HASH_UPPER_BITS 1
> +#define HSR_HASH_LOWER_BITS 2
> +#define HSR_HASH_XOR_BOTH_BITS 3
> +
> +#define REG_HSR_ALU_CTRL_1__1 0x0645
> +
> +#define HSR_LEARN_UCAST_DISABLE BIT(7)
> +#define HSR_FLUSH_TABLE BIT(5)
> +#define HSR_PROC_MCAST_SRC BIT(3)
> +#define HSR_AGING_ENABLE BIT(2)
> +
> +#define REG_HSR_ALU_CTRL_2__2 0x0646
> +
> +#define REG_HSR_ALU_AGE_PERIOD__4 0x0648
> +
> +#define REG_HSR_ALU_INT_STATUS__1 0x064C
> +#define REG_HSR_ALU_INT_MASK__1 0x064D
> +
> +#define HSR_WINDOW_OVERFLOW_INT BIT(3)
> +#define HSR_LEARN_FAIL_INT BIT(2)
> +#define HSR_ALMOST_FULL_INT BIT(1)
> +#define HSR_WRITE_FAIL_INT BIT(0)
> +
> +#define REG_HSR_ALU_ENTRY_0__2 0x0650
> +
> +#define HSR_ENTRY_INDEX_M (BIT(10) - 1)
> +#define HSR_FAIL_INDEX_M (BIT(8) - 1)
> +
> +#define REG_HSR_ALU_ENTRY_1__2 0x0652
> +
> +#define HSR_FAIL_LEARN_INDEX_M (BIT(8) - 1)
> +
> +#define REG_HSR_ALU_ENTRY_3__2 0x0654
> +
> +#define HSR_CPU_ACCESS_ENTRY_INDEX_M (BIT(8) - 1)
> +
> +/* 0 - Operation */
> +#define REG_PORT_DEFAULT_VID 0x0000
> +
> +#define REG_PORT_CUSTOM_VID 0x0002
> +#define REG_PORT_AVB_SR_1_VID 0x0004
> +#define REG_PORT_AVB_SR_2_VID 0x0006
> +
> +#define REG_PORT_AVB_SR_1_TYPE 0x0008
> +#define REG_PORT_AVB_SR_2_TYPE 0x000A
> +
> +#define REG_PORT_PME_STATUS 0x0013
> +#define REG_PORT_PME_CTRL 0x0017
> +
> +#define PME_WOL_MAGICPKT BIT(2)
> +#define PME_WOL_LINKUP BIT(1)
> +#define PME_WOL_ENERGY BIT(0)
> +
> +#define REG_PORT_INT_STATUS 0x001B
> +#define REG_PORT_INT_MASK 0x001F
> +
> +#define PORT_SGMII_INT BIT(3)
> +#define PORT_PTP_INT BIT(2)
> +#define PORT_PHY_INT BIT(1)
> +#define PORT_ACL_INT BIT(0)
> +
> +#define PORT_INT_MASK \
> + (PORT_SGMII_INT | PORT_PTP_INT | PORT_PHY_INT | PORT_ACL_INT)
> +
> +#define REG_PORT_CTRL_0 0x0020
> +
> +#define PORT_MAC_LOOPBACK BIT(7)
> +#define PORT_FORCE_TX_FLOW_CTRL BIT(4)
> +#define PORT_FORCE_RX_FLOW_CTRL BIT(3)
> +#define PORT_TAIL_TAG_ENABLE BIT(2)
> +#define PORT_QUEUE_SPLIT_ENABLE 0x3
> +
> +#define REG_PORT_CTRL_1 0x0021
> +
> +#define PORT_SRP_ENABLE 0x3
> +
> +#define REG_PORT_STATUS_0 0x0030
> +
> +#define PORT_INTF_SPEED_M 0x3
> +#define PORT_INTF_SPEED_S 3
> +#define PORT_INTF_FULL_DUPLEX BIT(2)
> +#define PORT_TX_FLOW_CTRL BIT(1)
> +#define PORT_RX_FLOW_CTRL BIT(0)
> +
> +#define REG_PORT_STATUS_1 0x0034
> +
> +/* 1 - PHY */
> +#define REG_PORT_PHY_CTRL 0x0100
> +
> +#define PORT_PHY_RESET BIT(15)
> +#define PORT_PHY_LOOPBACK BIT(14)
> +#define PORT_SPEED_100MBIT BIT(13)
> +#define PORT_AUTO_NEG_ENABLE BIT(12)
> +#define PORT_POWER_DOWN BIT(11)
> +#define PORT_ISOLATE BIT(10)
> +#define PORT_AUTO_NEG_RESTART BIT(9)
> +#define PORT_FULL_DUPLEX BIT(8)
> +#define PORT_COLLISION_TEST BIT(7)
> +#define PORT_SPEED_1000MBIT BIT(6)
> +
> +#define REG_PORT_PHY_STATUS 0x0102
> +
> +#define PORT_100BT4_CAPABLE BIT(15)
> +#define PORT_100BTX_FD_CAPABLE BIT(14)
> +#define PORT_100BTX_CAPABLE BIT(13)
> +#define PORT_10BT_FD_CAPABLE BIT(12)
> +#define PORT_10BT_CAPABLE BIT(11)
> +#define PORT_EXTENDED_STATUS BIT(8)
> +#define PORT_MII_SUPPRESS_CAPABLE BIT(6)
> +#define PORT_AUTO_NEG_ACKNOWLEDGE BIT(5)
> +#define PORT_REMOTE_FAULT BIT(4)
> +#define PORT_AUTO_NEG_CAPABLE BIT(3)
> +#define PORT_LINK_STATUS BIT(2)
> +#define PORT_JABBER_DETECT BIT(1)
> +#define PORT_EXTENDED_CAPABILITY BIT(0)
> +
> +#define REG_PORT_PHY_ID_HI 0x0104
> +#define REG_PORT_PHY_ID_LO 0x0106
> +
> +#define KSZ9477_ID_HI 0x0022
> +#define KSZ9477_ID_LO 0x1622
> +
> +#define REG_PORT_PHY_AUTO_NEGOTIATION 0x0108
> +
> +#define PORT_AUTO_NEG_NEXT_PAGE BIT(15)
> +#define PORT_AUTO_NEG_REMOTE_FAULT BIT(13)
> +#define PORT_AUTO_NEG_ASYM_PAUSE BIT(11)
> +#define PORT_AUTO_NEG_SYM_PAUSE BIT(10)
> +#define PORT_AUTO_NEG_100BT4 BIT(9)
> +#define PORT_AUTO_NEG_100BTX_FD BIT(8)
> +#define PORT_AUTO_NEG_100BTX BIT(7)
> +#define PORT_AUTO_NEG_10BT_FD BIT(6)
> +#define PORT_AUTO_NEG_10BT BIT(5)
> +#define PORT_AUTO_NEG_SELECTOR 0x001F
> +#define PORT_AUTO_NEG_802_3 0x0001
> +
> +#define PORT_AUTO_NEG_PAUSE \
> + (PORT_AUTO_NEG_ASYM_PAUSE | PORT_AUTO_NEG_SYM_PAUSE)
> +
> +#define REG_PORT_PHY_REMOTE_CAPABILITY 0x010A
> +
> +#define PORT_REMOTE_NEXT_PAGE BIT(15)
> +#define PORT_REMOTE_ACKNOWLEDGE BIT(14)
> +#define PORT_REMOTE_REMOTE_FAULT BIT(13)
> +#define PORT_REMOTE_ASYM_PAUSE BIT(11)
> +#define PORT_REMOTE_SYM_PAUSE BIT(10)
> +#define PORT_REMOTE_100BTX_FD BIT(8)
> +#define PORT_REMOTE_100BTX BIT(7)
> +#define PORT_REMOTE_10BT_FD BIT(6)
> +#define PORT_REMOTE_10BT BIT(5)
> +
> +#define REG_PORT_PHY_1000_CTRL 0x0112
> +
> +#define PORT_AUTO_NEG_MANUAL BIT(12)
> +#define PORT_AUTO_NEG_MASTER BIT(11)
> +#define PORT_AUTO_NEG_MASTER_PREFERRED BIT(10)
> +#define PORT_AUTO_NEG_1000BT_FD BIT(9)
> +#define PORT_AUTO_NEG_1000BT BIT(8)
> +
> +#define REG_PORT_PHY_1000_STATUS 0x0114
> +
> +#define PORT_MASTER_FAULT BIT(15)
> +#define PORT_LOCAL_MASTER BIT(14)
> +#define PORT_LOCAL_RX_OK BIT(13)
> +#define PORT_REMOTE_RX_OK BIT(12)
> +#define PORT_REMOTE_1000BT_FD BIT(11)
> +#define PORT_REMOTE_1000BT BIT(10)
> +#define PORT_REMOTE_IDLE_CNT_M 0x0F
> +
> +#define PORT_PHY_1000_STATIC_STATUS \
> + (PORT_LOCAL_RX_OK | \
> + PORT_REMOTE_RX_OK | \
> + PORT_REMOTE_1000BT_FD | \
> + PORT_REMOTE_1000BT)
> +
> +#define REG_PORT_PHY_MMD_SETUP 0x011A
> +
> +#define PORT_MMD_OP_MODE_M 0x3
> +#define PORT_MMD_OP_MODE_S 14
> +#define PORT_MMD_OP_INDEX 0
> +#define PORT_MMD_OP_DATA_NO_INCR 1
> +#define PORT_MMD_OP_DATA_INCR_RW 2
> +#define PORT_MMD_OP_DATA_INCR_W 3
> +#define PORT_MMD_DEVICE_ID_M 0x1F
> +
> +#define MMD_SETUP(mode, dev) \
> + (((u16)(mode) << PORT_MMD_OP_MODE_S) | (dev))
> +
> +#define REG_PORT_PHY_MMD_INDEX_DATA 0x011C
> +
> +#define MMD_DEVICE_ID_DSP 1
> +
> +#define MMD_DSP_SQI_CHAN_A 0xAC
> +#define MMD_DSP_SQI_CHAN_B 0xAD
> +#define MMD_DSP_SQI_CHAN_C 0xAE
> +#define MMD_DSP_SQI_CHAN_D 0xAF
> +
> +#define DSP_SQI_ERR_DETECTED BIT(15)
> +#define DSP_SQI_AVG_ERR 0x7FFF
> +
> +#define MMD_DEVICE_ID_COMMON 2
> +
> +#define MMD_DEVICE_ID_EEE_ADV 7
> +
> +#define MMD_EEE_ADV 0x3C
> +#define EEE_ADV_100MBIT BIT(1)
> +#define EEE_ADV_1GBIT BIT(2)
> +
> +#define MMD_EEE_LP_ADV 0x3D
> +#define MMD_EEE_MSG_CODE 0x3F
> +
> +#define MMD_DEVICE_ID_AFED 0x1C
> +
> +#define REG_PORT_PHY_EXTENDED_STATUS 0x011E
> +
> +#define PORT_100BTX_FD_ABLE BIT(15)
> +#define PORT_100BTX_ABLE BIT(14)
> +#define PORT_10BT_FD_ABLE BIT(13)
> +#define PORT_10BT_ABLE BIT(12)
> +
> +#define REG_PORT_SGMII_ADDR__4 0x0200
> +#define PORT_SGMII_AUTO_INCR BIT(23)
> +#define PORT_SGMII_DEVICE_ID_M 0x1F
> +#define PORT_SGMII_DEVICE_ID_S 16
> +#define PORT_SGMII_ADDR_M (BIT(21) - 1)
> +
> +#define REG_PORT_SGMII_DATA__4 0x0204
> +#define PORT_SGMII_DATA_M (BIT(16) - 1)
> +
> +#define MMD_DEVICE_ID_PMA 0x01
> +#define MMD_DEVICE_ID_PCS 0x03
> +#define MMD_DEVICE_ID_PHY_XS 0x04
> +#define MMD_DEVICE_ID_DTE_XS 0x05
> +#define MMD_DEVICE_ID_AN 0x07
> +#define MMD_DEVICE_ID_VENDOR_CTRL 0x1E
> +#define MMD_DEVICE_ID_VENDOR_MII 0x1F
> +
> +#define SR_MII MMD_DEVICE_ID_VENDOR_MII
> +
> +#define MMD_SR_MII_CTRL 0x0000
> +
> +#define SR_MII_RESET BIT(15)
> +#define SR_MII_LOOPBACK BIT(14)
> +#define SR_MII_SPEED_100MBIT BIT(13)
> +#define SR_MII_AUTO_NEG_ENABLE BIT(12)
> +#define SR_MII_POWER_DOWN BIT(11)
> +#define SR_MII_AUTO_NEG_RESTART BIT(9)
> +#define SR_MII_FULL_DUPLEX BIT(8)
> +#define SR_MII_SPEED_1000MBIT BIT(6)
> +
> +#define MMD_SR_MII_STATUS 0x0001
> +#define MMD_SR_MII_ID_1 0x0002
> +#define MMD_SR_MII_ID_2 0x0003
> +#define MMD_SR_MII_AUTO_NEGOTIATION 0x0004
> +
> +#define SR_MII_AUTO_NEG_NEXT_PAGE BIT(15)
> +#define SR_MII_AUTO_NEG_REMOTE_FAULT_M 0x3
> +#define SR_MII_AUTO_NEG_REMOTE_FAULT_S 12
> +#define SR_MII_AUTO_NEG_NO_ERROR 0
> +#define SR_MII_AUTO_NEG_OFFLINE 1
> +#define SR_MII_AUTO_NEG_LINK_FAILURE 2
> +#define SR_MII_AUTO_NEG_ERROR 3
> +#define SR_MII_AUTO_NEG_PAUSE_M 0x3
> +#define SR_MII_AUTO_NEG_PAUSE_S 7
> +#define SR_MII_AUTO_NEG_NO_PAUSE 0
> +#define SR_MII_AUTO_NEG_ASYM_PAUSE_TX 1
> +#define SR_MII_AUTO_NEG_SYM_PAUSE 2
> +#define SR_MII_AUTO_NEG_ASYM_PAUSE_RX 3
> +#define SR_MII_AUTO_NEG_HALF_DUPLEX BIT(6)
> +#define SR_MII_AUTO_NEG_FULL_DUPLEX BIT(5)
> +
> +#define MMD_SR_MII_REMOTE_CAPABILITY 0x0005
> +#define MMD_SR_MII_AUTO_NEG_EXP 0x0006
> +#define MMD_SR_MII_AUTO_NEG_EXT 0x000F
> +
> +#define MMD_SR_MII_DIGITAL_CTRL_1 0x8000
> +
> +#define MMD_SR_MII_AUTO_NEG_CTRL 0x8001
> +
> +#define SR_MII_8_BIT BIT(8)
> +#define SR_MII_SGMII_LINK_UP BIT(4)
> +#define SR_MII_TX_CFG_PHY_MASTER BIT(3)
> +#define SR_MII_PCS_MODE_M 0x3
> +#define SR_MII_PCS_MODE_S 1
> +#define SR_MII_PCS_SGMII 2
> +#define SR_MII_AUTO_NEG_COMPLETE_INTR BIT(0)
> +
> +#define MMD_SR_MII_AUTO_NEG_STATUS 0x8002
> +
> +#define SR_MII_STAT_LINK_UP BIT(4)
> +#define SR_MII_STAT_M 0x3
> +#define SR_MII_STAT_S 2
> +#define SR_MII_STAT_10_MBPS 0
> +#define SR_MII_STAT_100_MBPS 1
> +#define SR_MII_STAT_1000_MBPS 2
> +#define SR_MII_STAT_FULL_DUPLEX BIT(1)
> +
> +#define MMD_SR_MII_PHY_CTRL 0x80A0
> +
> +#define SR_MII_PHY_LANE_SEL_M 0xF
> +#define SR_MII_PHY_LANE_SEL_S 8
> +#define SR_MII_PHY_WRITE BIT(1)
> +#define SR_MII_PHY_START_BUSY BIT(0)
> +
> +#define MMD_SR_MII_PHY_ADDR 0x80A1
> +
> +#define SR_MII_PHY_ADDR_M (BIT(16) - 1)
> +
> +#define MMD_SR_MII_PHY_DATA 0x80A2
> +
> +#define SR_MII_PHY_DATA_M (BIT(16) - 1)
> +
> +#define SR_MII_PHY_JTAG_CHIP_ID_HI 0x000C
> +#define SR_MII_PHY_JTAG_CHIP_ID_LO 0x000D
> +
> +#define REG_PORT_PHY_REMOTE_LB_LED 0x0122
> +
> +#define PORT_REMOTE_LOOPBACK BIT(8)
> +#define PORT_LED_SELECT (3 << 6)
> +#define PORT_LED_CTRL (3 << 4)
> +#define PORT_LED_CTRL_TEST BIT(3)
> +#define PORT_10BT_PREAMBLE BIT(2)
> +#define PORT_LINK_MD_10BT_ENABLE BIT(1)
> +#define PORT_LINK_MD_PASS BIT(0)
> +
> +#define REG_PORT_PHY_LINK_MD 0x0124
> +
> +#define PORT_START_CABLE_DIAG BIT(15)
> +#define PORT_TX_DISABLE BIT(14)
> +#define PORT_CABLE_DIAG_PAIR_M 0x3
> +#define PORT_CABLE_DIAG_PAIR_S 12
> +#define PORT_CABLE_DIAG_SELECT_M 0x3
> +#define PORT_CABLE_DIAG_SELECT_S 10
> +#define PORT_CABLE_DIAG_RESULT_M 0x3
> +#define PORT_CABLE_DIAG_RESULT_S 8
> +#define PORT_CABLE_STAT_NORMAL 0
> +#define PORT_CABLE_STAT_OPEN 1
> +#define PORT_CABLE_STAT_SHORT 2
> +#define PORT_CABLE_STAT_FAILED 3
> +#define PORT_CABLE_FAULT_COUNTER 0x00FF
> +
> +#define REG_PORT_PHY_PMA_STATUS 0x0126
> +
> +#define PORT_1000_LINK_GOOD BIT(1)
> +#define PORT_100_LINK_GOOD BIT(0)
> +
> +#define REG_PORT_PHY_DIGITAL_STATUS 0x0128
> +
> +#define PORT_LINK_DETECT BIT(14)
> +#define PORT_SIGNAL_DETECT BIT(13)
> +#define PORT_PHY_STAT_MDI BIT(12)
> +#define PORT_PHY_STAT_MASTER BIT(11)
> +
> +#define REG_PORT_PHY_RXER_COUNTER 0x012A
> +
> +#define REG_PORT_PHY_INT_ENABLE 0x0136
> +#define REG_PORT_PHY_INT_STATUS 0x0137
> +
> +#define JABBER_INT BIT(7)
> +#define RX_ERR_INT BIT(6)
> +#define PAGE_RX_INT BIT(5)
> +#define PARALLEL_DETECT_FAULT_INT BIT(4)
> +#define LINK_PARTNER_ACK_INT BIT(3)
> +#define LINK_DOWN_INT BIT(2)
> +#define REMOTE_FAULT_INT BIT(1)
> +#define LINK_UP_INT BIT(0)
> +
> +#define REG_PORT_PHY_DIGITAL_DEBUG_1 0x0138
> +
> +#define PORT_REG_CLK_SPEED_25_MHZ BIT(14)
> +#define PORT_PHY_FORCE_MDI BIT(7)
> +#define PORT_PHY_AUTO_MDIX_DISABLE BIT(6)
> +
> +/* Same as PORT_PHY_LOOPBACK */
> +#define PORT_PHY_PCS_LOOPBACK BIT(0)
> +
> +#define REG_PORT_PHY_DIGITAL_DEBUG_2 0x013A
> +
> +#define REG_PORT_PHY_DIGITAL_DEBUG_3 0x013C
> +
> +#define PORT_100BT_FIXED_LATENCY BIT(15)
> +
> +#define REG_PORT_PHY_PHY_CTRL 0x013E
> +
> +#define PORT_INT_PIN_HIGH BIT(14)
> +#define PORT_ENABLE_JABBER BIT(9)
> +#define PORT_STAT_SPEED_1000MBIT BIT(6)
> +#define PORT_STAT_SPEED_100MBIT BIT(5)
> +#define PORT_STAT_SPEED_10MBIT BIT(4)
> +#define PORT_STAT_FULL_DUPLEX BIT(3)
> +
> +/* Same as PORT_PHY_STAT_MASTER */
> +#define PORT_STAT_MASTER BIT(2)
> +#define PORT_RESET BIT(1)
> +#define PORT_LINK_STATUS_FAIL BIT(0)
> +
> +/* 3 - xMII */
> +#define REG_PORT_XMII_CTRL_0 0x0300
> +
> +#define PORT_SGMII_SEL BIT(7)
> +#define PORT_MII_FULL_DUPLEX BIT(6)
> +#define PORT_MII_100MBIT BIT(4)
> +#define PORT_GRXC_ENABLE BIT(0)
> +
> +#define REG_PORT_XMII_CTRL_1 0x0301
> +
> +#define PORT_RMII_CLK_SEL BIT(7)
> +/* S1 */
> +#define PORT_MII_1000MBIT_S1 BIT(6)
> +/* S2 */
> +#define PORT_MII_NOT_1GBIT BIT(6)
> +#define PORT_MII_SEL_EDGE BIT(5)
> +#define PORT_RGMII_ID_IG_ENABLE BIT(4)
> +#define PORT_RGMII_ID_EG_ENABLE BIT(3)
> +#define PORT_MII_MAC_MODE BIT(2)
> +#define PORT_MII_SEL_M 0x3
> +/* S1 */
> +#define PORT_MII_SEL_S1 0x0
> +#define PORT_RMII_SEL_S1 0x1
> +#define PORT_GMII_SEL_S1 0x2
> +#define PORT_RGMII_SEL_S1 0x3
> +/* S2 */
> +#define PORT_RGMII_SEL 0x0
> +#define PORT_RMII_SEL 0x1
> +#define PORT_GMII_SEL 0x2
> +#define PORT_MII_SEL 0x3
> +
> +/* 4 - MAC */
> +#define REG_PORT_MAC_CTRL_0 0x0400
> +
> +#define PORT_BROADCAST_STORM BIT(1)
> +#define PORT_JUMBO_FRAME BIT(0)
> +
> +#define REG_PORT_MAC_CTRL_1 0x0401
> +
> +#define PORT_BACK_PRESSURE BIT(3)
> +#define PORT_PASS_ALL BIT(0)
> +
> +#define REG_PORT_MAC_CTRL_2 0x0402
> +
> +#define PORT_100BT_EEE_DISABLE BIT(7)
> +#define PORT_1000BT_EEE_DISABLE BIT(6)
> +
> +#define REG_PORT_MAC_IN_RATE_LIMIT 0x0403
> +
> +#define PORT_IN_PORT_BASED_S 6
> +#define PORT_RATE_PACKET_BASED_S 5
> +#define PORT_IN_FLOW_CTRL_S 4
> +#define PORT_COUNT_IFG_S 1
> +#define PORT_COUNT_PREAMBLE_S 0
> +#define PORT_IN_PORT_BASED BIT(6)
> +#define PORT_IN_PACKET_BASED BIT(5)
> +#define PORT_IN_FLOW_CTRL BIT(4)
> +#define PORT_IN_LIMIT_MODE_M 0x3
> +#define PORT_IN_LIMIT_MODE_S 2
> +#define PORT_IN_ALL 0
> +#define PORT_IN_UNICAST 1
> +#define PORT_IN_MULTICAST 2
> +#define PORT_IN_BROADCAST 3
> +#define PORT_COUNT_IFG BIT(1)
> +#define PORT_COUNT_PREAMBLE BIT(0)
> +
> +#define REG_PORT_IN_RATE_0 0x0410
> +#define REG_PORT_IN_RATE_1 0x0411
> +#define REG_PORT_IN_RATE_2 0x0412
> +#define REG_PORT_IN_RATE_3 0x0413
> +#define REG_PORT_IN_RATE_4 0x0414
> +#define REG_PORT_IN_RATE_5 0x0415
> +#define REG_PORT_IN_RATE_6 0x0416
> +#define REG_PORT_IN_RATE_7 0x0417
> +
> +#define REG_PORT_OUT_RATE_0 0x0420
> +#define REG_PORT_OUT_RATE_1 0x0421
> +#define REG_PORT_OUT_RATE_2 0x0422
> +#define REG_PORT_OUT_RATE_3 0x0423
> +
> +#define PORT_RATE_LIMIT_M (BIT(7) - 1)
> +
> +/* 5 - MIB Counters */
> +#define REG_PORT_MIB_CTRL_STAT__4 0x0500
> +
> +#define MIB_COUNTER_OVERFLOW BIT(31)
> +#define MIB_COUNTER_VALID BIT(30)
> +#define MIB_COUNTER_READ BIT(25)
> +#define MIB_COUNTER_FLUSH_FREEZE BIT(24)
> +#define MIB_COUNTER_INDEX_M (BIT(8) - 1)
> +#define MIB_COUNTER_INDEX_S 16
> +#define MIB_COUNTER_DATA_HI_M 0xF
> +
> +#define REG_PORT_MIB_DATA 0x0504
> +
> +/* 6 - ACL */
> +#define REG_PORT_ACL_0 0x0600
> +
> +#define ACL_FIRST_RULE_M 0xF
> +
> +#define REG_PORT_ACL_1 0x0601
> +
> +#define ACL_MODE_M 0x3
> +#define ACL_MODE_S 4
> +#define ACL_MODE_DISABLE 0
> +#define ACL_MODE_LAYER_2 1
> +#define ACL_MODE_LAYER_3 2
> +#define ACL_MODE_LAYER_4 3
> +#define ACL_ENABLE_M 0x3
> +#define ACL_ENABLE_S 2
> +#define ACL_ENABLE_2_COUNT 0
> +#define ACL_ENABLE_2_TYPE 1
> +#define ACL_ENABLE_2_MAC 2
> +#define ACL_ENABLE_2_BOTH 3
> +#define ACL_ENABLE_3_IP 1
> +#define ACL_ENABLE_3_SRC_DST_COMP 2
> +#define ACL_ENABLE_4_PROTOCOL 0
> +#define ACL_ENABLE_4_TCP_PORT_COMP 1
> +#define ACL_ENABLE_4_UDP_PORT_COMP 2
> +#define ACL_ENABLE_4_TCP_SEQN_COMP 3
> +#define ACL_SRC BIT(1)
> +#define ACL_EQUAL BIT(0)
> +
> +#define REG_PORT_ACL_2 0x0602
> +#define REG_PORT_ACL_3 0x0603
> +
> +#define ACL_MAX_PORT 0xFFFF
> +
> +#define REG_PORT_ACL_4 0x0604
> +#define REG_PORT_ACL_5 0x0605
> +
> +#define ACL_MIN_PORT 0xFFFF
> +#define ACL_IP_ADDR 0xFFFFFFFF
> +#define ACL_TCP_SEQNUM 0xFFFFFFFF
> +
> +#define REG_PORT_ACL_6 0x0606
> +
> +#define ACL_RESERVED 0xF8
> +#define ACL_PORT_MODE_M 0x3
> +#define ACL_PORT_MODE_S 1
> +#define ACL_PORT_MODE_DISABLE 0
> +#define ACL_PORT_MODE_EITHER 1
> +#define ACL_PORT_MODE_IN_RANGE 2
> +#define ACL_PORT_MODE_OUT_OF_RANGE 3
> +
> +#define REG_PORT_ACL_7 0x0607
> +
> +#define ACL_TCP_FLAG_ENABLE BIT(0)
> +
> +#define REG_PORT_ACL_8 0x0608
> +
> +#define ACL_TCP_FLAG_M 0xFF
> +
> +#define REG_PORT_ACL_9 0x0609
> +
> +#define ACL_TCP_FLAG 0xFF
> +#define ACL_ETH_TYPE 0xFFFF
> +#define ACL_IP_M 0xFFFFFFFF
> +
> +#define REG_PORT_ACL_A 0x060A
> +
> +#define ACL_PRIO_MODE_M 0x3
> +#define ACL_PRIO_MODE_S 6
> +#define ACL_PRIO_MODE_DISABLE 0
> +#define ACL_PRIO_MODE_HIGHER 1
> +#define ACL_PRIO_MODE_LOWER 2
> +#define ACL_PRIO_MODE_REPLACE 3
> +#define ACL_PRIO_M KS_PRIO_M
> +#define ACL_PRIO_S 3
> +#define ACL_VLAN_PRIO_REPLACE BIT(2)
> +#define ACL_VLAN_PRIO_M KS_PRIO_M
> +#define ACL_VLAN_PRIO_HI_M 0x3
> +
> +#define REG_PORT_ACL_B 0x060B
> +
> +#define ACL_VLAN_PRIO_LO_M 0x8
> +#define ACL_VLAN_PRIO_S 7
> +#define ACL_MAP_MODE_M 0x3
> +#define ACL_MAP_MODE_S 5
> +#define ACL_MAP_MODE_DISABLE 0
> +#define ACL_MAP_MODE_OR 1
> +#define ACL_MAP_MODE_AND 2
> +#define ACL_MAP_MODE_REPLACE 3
> +
> +#define ACL_CNT_M (BIT(11) - 1)
> +#define ACL_CNT_S 5
> +
> +#define REG_PORT_ACL_C 0x060C
> +
> +#define REG_PORT_ACL_D 0x060D
> +#define ACL_MSEC_UNIT BIT(6)
> +#define ACL_INTR_MODE BIT(5)
> +#define ACL_PORT_MAP 0x7F
> +
> +#define REG_PORT_ACL_E 0x060E
> +#define REG_PORT_ACL_F 0x060F
> +
> +#define REG_PORT_ACL_BYTE_EN_MSB 0x0610
> +#define REG_PORT_ACL_BYTE_EN_LSB 0x0611
> +
> +#define ACL_ACTION_START 0xA
> +#define ACL_ACTION_LEN 4
> +#define ACL_INTR_CNT_START 0xD
> +#define ACL_RULESET_START 0xE
> +#define ACL_RULESET_LEN 2
> +#define ACL_TABLE_LEN 16
> +
> +#define ACL_ACTION_ENABLE 0x003C
> +#define ACL_MATCH_ENABLE 0x7FC3
> +#define ACL_RULESET_ENABLE 0x8003
> +#define ACL_BYTE_ENABLE 0xFFFF
> +
> +#define REG_PORT_ACL_CTRL_0 0x0612
> +
> +#define PORT_ACL_WRITE_DONE BIT(6)
> +#define PORT_ACL_READ_DONE BIT(5)
> +#define PORT_ACL_WRITE BIT(4)
> +#define PORT_ACL_INDEX_M 0xF
> +
> +#define REG_PORT_ACL_CTRL_1 0x0613
> +
> +/* 8 - Classification and Policing */
> +#define REG_PORT_MRI_MIRROR_CTRL 0x0800
> +
> +#define PORT_MIRROR_RX BIT(6)
> +#define PORT_MIRROR_TX BIT(5)
> +#define PORT_MIRROR_SNIFFER BIT(1)
> +
> +#define REG_PORT_MRI_PRIO_CTRL 0x0801
> +
> +#define PORT_HIGHEST_PRIO BIT(7)
> +#define PORT_OR_PRIO BIT(6)
> +#define PORT_MAC_PRIO_ENABLE BIT(4)
> +#define PORT_VLAN_PRIO_ENABLE BIT(3)
> +#define PORT_802_1P_PRIO_ENABLE BIT(2)
> +#define PORT_DIFFSERV_PRIO_ENABLE BIT(1)
> +#define PORT_ACL_PRIO_ENABLE BIT(0)
> +
> +#define REG_PORT_MRI_MAC_CTRL 0x0802
> +
> +#define PORT_USER_PRIO_CEILING BIT(7)
> +#define PORT_DROP_NON_VLAN BIT(4)
> +#define PORT_DROP_TAG BIT(3)
> +#define PORT_BASED_PRIO_M KS_PRIO_M
> +#define PORT_BASED_PRIO_S 0
> +
> +#define REG_PORT_MRI_AUTHEN_CTRL 0x0803
> +
> +#define PORT_ACL_ENABLE BIT(2)
> +#define PORT_AUTHEN_MODE 0x3
> +#define PORT_AUTHEN_PASS 0
> +#define PORT_AUTHEN_BLOCK 1
> +#define PORT_AUTHEN_TRAP 2
> +
> +#define REG_PORT_MRI_INDEX__4 0x0804
> +
> +#define MRI_INDEX_P_M 0x7
> +#define MRI_INDEX_P_S 16
> +#define MRI_INDEX_Q_M 0x3
> +#define MRI_INDEX_Q_S 0
> +
> +#define REG_PORT_MRI_TC_MAP__4 0x0808
> +
> +#define PORT_TC_MAP_M 0xf
> +#define PORT_TC_MAP_S 4
> +
> +#define REG_PORT_MRI_POLICE_CTRL__4 0x080C
> +
> +#define POLICE_DROP_ALL BIT(10)
> +#define POLICE_PACKET_TYPE_M 0x3
> +#define POLICE_PACKET_TYPE_S 8
> +#define POLICE_PACKET_DROPPED 0
> +#define POLICE_PACKET_GREEN 1
> +#define POLICE_PACKET_YELLOW 2
> +#define POLICE_PACKET_RED 3
> +#define PORT_BASED_POLICING BIT(7)
> +#define NON_DSCP_COLOR_M 0x3
> +#define NON_DSCP_COLOR_S 5
> +#define COLOR_MARK_ENABLE BIT(4)
> +#define COLOR_REMAP_ENABLE BIT(3)
> +#define POLICE_DROP_SRP BIT(2)
> +#define POLICE_COLOR_NOT_AWARE BIT(1)
> +#define POLICE_ENABLE BIT(0)
> +
> +#define REG_PORT_POLICE_COLOR_0__4 0x0810
> +#define REG_PORT_POLICE_COLOR_1__4 0x0814
> +#define REG_PORT_POLICE_COLOR_2__4 0x0818
> +#define REG_PORT_POLICE_COLOR_3__4 0x081C
> +
> +#define POLICE_COLOR_MAP_S 2
> +#define POLICE_COLOR_MAP_M (BIT(POLICE_COLOR_MAP_S) - 1)
> +
> +#define REG_PORT_POLICE_RATE__4 0x0820
> +
> +#define POLICE_CIR_S 16
> +#define POLICE_PIR_S 0
> +
> +#define REG_PORT_POLICE_BURST_SIZE__4 0x0824
> +
> +#define POLICE_BURST_SIZE_M 0x3FFF
> +#define POLICE_CBS_S 16
> +#define POLICE_PBS_S 0
> +
> +#define REG_PORT_WRED_PM_CTRL_0__4 0x0830
> +
> +#define WRED_PM_CTRL_M (BIT(11) - 1)
> +
> +#define WRED_PM_MAX_THRESHOLD_S 16
> +#define WRED_PM_MIN_THRESHOLD_S 0
> +
> +#define REG_PORT_WRED_PM_CTRL_1__4 0x0834
> +
> +#define WRED_PM_MULTIPLIER_S 16
> +#define WRED_PM_AVG_QUEUE_SIZE_S 0
> +
> +#define REG_PORT_WRED_QUEUE_CTRL_0__4 0x0840
> +#define REG_PORT_WRED_QUEUE_CTRL_1__4 0x0844
> +
> +#define REG_PORT_WRED_QUEUE_PMON__4 0x0848
> +
> +#define WRED_RANDOM_DROP_ENABLE BIT(31)
> +#define WRED_PMON_FLUSH BIT(30)
> +#define WRED_DROP_GYR_DISABLE BIT(29)
> +#define WRED_DROP_YR_DISABLE BIT(28)
> +#define WRED_DROP_R_DISABLE BIT(27)
> +#define WRED_DROP_ALL BIT(26)
> +#define WRED_PMON_M (BIT(24) - 1)
> +
> +/* 9 - Shaping */
> +
> +#define REG_PORT_MTI_QUEUE_INDEX__4 0x0900
> +
> +#define REG_PORT_MTI_QUEUE_CTRL_0__4 0x0904
> +
> +#define MTI_PVID_REPLACE BIT(0)
> +
> +#define REG_PORT_MTI_QUEUE_CTRL_0 0x0914
> +
> +#define MTI_SCHEDULE_MODE_M 0x3
> +#define MTI_SCHEDULE_MODE_S 6
> +#define MTI_SCHEDULE_STRICT_PRIO 0
> +#define MTI_SCHEDULE_WRR 2
> +#define MTI_SHAPING_M 0x3
> +#define MTI_SHAPING_S 4
> +#define MTI_SHAPING_OFF 0
> +#define MTI_SHAPING_SRP 1
> +#define MTI_SHAPING_TIME_AWARE 2
> +
> +#define REG_PORT_MTI_QUEUE_CTRL_1 0x0915
> +
> +#define MTI_TX_RATIO_M (BIT(7) - 1)
> +
> +#define REG_PORT_MTI_QUEUE_CTRL_2__2 0x0916
> +#define REG_PORT_MTI_HI_WATER_MARK 0x0916
> +#define REG_PORT_MTI_QUEUE_CTRL_3__2 0x0918
> +#define REG_PORT_MTI_LO_WATER_MARK 0x0918
> +#define REG_PORT_MTI_QUEUE_CTRL_4__2 0x091A
> +#define REG_PORT_MTI_CREDIT_INCREMENT 0x091A
> +
> +/* A - QM */
> +
> +#define REG_PORT_QM_CTRL__4 0x0A00
> +
> +#define PORT_QM_DROP_PRIO_M 0x3
> +
> +#define REG_PORT_VLAN_MEMBERSHIP__4 0x0A04
> +
> +#define REG_PORT_QM_QUEUE_INDEX__4 0x0A08
> +
> +#define PORT_QM_QUEUE_INDEX_S 24
> +#define PORT_QM_BURST_SIZE_S 16
> +#define PORT_QM_MIN_RESV_SPACE_M (BIT(11) - 1)
> +
> +#define REG_PORT_QM_WATER_MARK__4 0x0A0C
> +
> +#define PORT_QM_HI_WATER_MARK_S 16
> +#define PORT_QM_LO_WATER_MARK_S 0
> +#define PORT_QM_WATER_MARK_M (BIT(11) - 1)
> +
> +#define REG_PORT_QM_TX_CNT_0__4 0x0A10
> +
> +#define PORT_QM_TX_CNT_USED_S 0
> +#define PORT_QM_TX_CNT_M (BIT(11) - 1)
> +
> +#define REG_PORT_QM_TX_CNT_1__4 0x0A14
> +
> +#define PORT_QM_TX_CNT_CALCULATED_S 16
> +#define PORT_QM_TX_CNT_AVAIL_S 0
> +
> +/* B - LUE */
> +#define REG_PORT_LUE_CTRL 0x0B00
> +
> +#define PORT_VLAN_LOOKUP_VID_0 BIT(7)
> +#define PORT_INGRESS_FILTER BIT(6)
> +#define PORT_DISCARD_NON_VID BIT(5)
> +#define PORT_MAC_BASED_802_1X BIT(4)
> +#define PORT_SRC_ADDR_FILTER BIT(3)
> +
> +#define REG_PORT_LUE_MSTP_INDEX 0x0B01
> +
> +#define REG_PORT_LUE_MSTP_STATE 0x0B04
> +
> +#define PORT_TX_ENABLE BIT(2)
> +#define PORT_RX_ENABLE BIT(1)
> +#define PORT_LEARN_DISABLE BIT(0)
> +
> +/* C - PTP */
> +
> +#define REG_PTP_PORT_RX_DELAY__2 0x0C00
> +#define REG_PTP_PORT_TX_DELAY__2 0x0C02
> +#define REG_PTP_PORT_ASYM_DELAY__2 0x0C04
> +
> +#define REG_PTP_PORT_XDELAY_TS 0x0C08
> +#define REG_PTP_PORT_XDELAY_TS_H 0x0C08
> +#define REG_PTP_PORT_XDELAY_TS_L 0x0C0A
> +
> +#define REG_PTP_PORT_SYNC_TS 0x0C0C
> +#define REG_PTP_PORT_SYNC_TS_H 0x0C0C
> +#define REG_PTP_PORT_SYNC_TS_L 0x0C0E
> +
> +#define REG_PTP_PORT_PDRESP_TS 0x0C10
> +#define REG_PTP_PORT_PDRESP_TS_H 0x0C10
> +#define REG_PTP_PORT_PDRESP_TS_L 0x0C12
> +
> +#define REG_PTP_PORT_TX_INT_STATUS__2 0x0C14
> +#define REG_PTP_PORT_TX_INT_ENABLE__2 0x0C16
> +
> +#define PTP_PORT_SYNC_INT BIT(15)
> +#define PTP_PORT_XDELAY_REQ_INT BIT(14)
> +#define PTP_PORT_PDELAY_RESP_INT BIT(13)
> +
> +#define REG_PTP_PORT_LINK_DELAY__4 0x0C18
> +
> +#define PRIO_QUEUES 4
> +#define RX_PRIO_QUEUES 8
> +
> +#define KS_PRIO_IN_REG 2
> +
> +#define TOTAL_PORT_NUM 7
> +
> +#define KSZ9477_COUNTER_NUM 0x20
> +#define TOTAL_KSZ9477_COUNTER_NUM (KSZ9477_COUNTER_NUM + 2 + 2)
> +
> +#define SWITCH_COUNTER_NUM KSZ9477_COUNTER_NUM
> +#define TOTAL_SWITCH_COUNTER_NUM TOTAL_KSZ9477_COUNTER_NUM
> +
> +#define P_BCAST_STORM_CTRL REG_PORT_MAC_CTRL_0
> +#define P_PRIO_CTRL REG_PORT_MRI_PRIO_CTRL
> +#define P_MIRROR_CTRL REG_PORT_MRI_MIRROR_CTRL
> +#define P_STP_CTRL REG_PORT_LUE_MSTP_STATE
> +#define P_PHY_CTRL REG_PORT_PHY_CTRL
> +#define P_NEG_RESTART_CTRL REG_PORT_PHY_CTRL
> +#define P_LINK_STATUS REG_PORT_PHY_STATUS
> +#define P_SPEED_STATUS REG_PORT_PHY_PHY_CTRL
> +#define P_RATE_LIMIT_CTRL REG_PORT_MAC_IN_RATE_LIMIT
> +
> +#define S_LINK_AGING_CTRL REG_SW_LUE_CTRL_1
> +#define S_MIRROR_CTRL REG_SW_MRI_CTRL_0
> +#define S_REPLACE_VID_CTRL REG_SW_MAC_CTRL_2
> +#define S_802_1P_PRIO_CTRL REG_SW_MAC_802_1P_MAP_0
> +#define S_TOS_PRIO_CTRL REG_SW_MAC_TOS_PRIO_0
> +#define S_FLUSH_TABLE_CTRL REG_SW_LUE_CTRL_1
> +
> +#define SW_FLUSH_DYN_MAC_TABLE SW_FLUSH_MSTP_TABLE
> +
> +#define MAX_TIMESTAMP_UNIT 2
> +#define MAX_TRIG_UNIT 3
> +#define MAX_TIMESTAMP_EVENT_UNIT 8
> +#define MAX_GPIO 4
> +
> +#define PTP_TRIG_UNIT_M (BIT(MAX_TRIG_UNIT) - 1)
> +#define PTP_TS_UNIT_M (BIT(MAX_TIMESTAMP_UNIT) - 1)
> +
> +/* Driver set switch broadcast storm protection at 10% rate. */
> +#define BROADCAST_STORM_PROT_RATE 10
> +
> +/* 148,800 frames * 67 ms / 100 */
> +#define BROADCAST_STORM_VALUE 9969
> +
> +#endif /* KSZ9477_REGS_H */
--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
More information about the barebox
mailing list