[PATCH] fixup! ARM: i.MX7: add 96Boards Meerkat96 support

[Johannes Zink]

This is a fixup for the documentation: fixed line breaks, whitespace changes 
and typos as requested.

Signed-off-by: Johannes Zink <j.zink at pengutronix.de>
---
 Documentation/boards/imx/meerkat96.rst | 28 ++++++++++++++++++--------
 1 file changed, 20 insertions(+), 8 deletions(-)

diff --git a/Documentation/boards/imx/meerkat96.rst b/Documentation/boards/imx/meerkat96.rst
index 3cdb1beaf..3a51b9144 100644
--- a/Documentation/boards/imx/meerkat96.rst
+++ b/Documentation/boards/imx/meerkat96.rst
@@ -1,28 +1,40 @@
 Meerkat 96
 ==========
 
-The Meerkat96 is a single board computer based on an i.MX7D SoC by NXP, featuring a dual core ARM Cortex-A7 at 1 GHz and a Cortex-M4 at 266MHz and 512 MB DRAM. For further details on the board's features check the manufacturers page at https://www.96boards.org/product/imx7-96
+The Meerkat96 is a single board computer based on an i.MX7D SoC by NXP, 
+featuring a dual core ARM Cortex-A7 at 1 GHz and a Cortex-M4 at 266MHz 
+and 512 MB DRAM. For further details on the board's features check the 
+manufacturers page at https://www.96boards.org/product/imx7-96
 
 Serial console
 --------------
 
-UART6 of the i.MX7D is broken out to Pinheader J3, on the Silkscreen the Pins are labeled with B (Ground), W (UART 6 TX) and G (UART 6 RX). If you use the UART-To-Serial-Converter provided with the board, you can just connect the Black jumper to B, the White to W and the Green to G. The UART uses 3.3V levels. 
+UART6 of the i.MX7D is broken out to Pinheader J3, on the Silkscreen 
+the Pins are labeled with B (Ground), W (UART 6 TX) and G (UART 6 RX). 
+If you use the UART-To-USB-Converter provided with the board, you can 
+just connect the Black jumper to B, the White to W and the Green to G. 
+
+The UART uses 3.3V levels. 
 
 Building Barebox                                                        
 ----------------                                                        
                                                                         
-To build Barebox for ZII i.MX7 based boards do the following:           
-                                                                        
-.. code-block:: sh                                                      
-           
-  make ARCH=arm CROSS_COMPILE=<ARM toolchain prefix> mrproper   
+To build Barebox for the meerkat96 board do the following:
+
+.. code-block:: sh
+
+  make ARCH=arm CROSS_COMPILE=<ARM toolchain prefix> mrproper
   make ARCH=arm CROSS_COMPILE=<ARM toolchain prefix> imx_v7_defconfig
   make ARCH=arm CROSS_COMPILE=<ARM toolchain prefix>
 
 Bringup
 -------
 
-flash the resulting barebox-meerkat96.img to an sdcard at address 0. Make sure the pmic is set to power-on state by setting the dipswitch SW3 on the boards bottom side to 1-1 (i.e. all switches on, which is the factory default).
+flash the resulting barebox-meerkat96.img to an sdcard at address 0. 
+
+Make sure the pmic is set to power-on state by setting the dipswitch 
+SW3 on the boards bottom side to 1-1 (i.e. all switches on, which is 
+the factory default).
 
 Schematics
 ----------
-- 
2.30.2