[PATCH v3] ARM: imx: add support for TQMa6UL SoM on MBa6ulxl
Rouven Czerwinski
r.czerwinski at pengutronix.de
Fri Feb 11 02:02:25 PST 2022
Add support for a TQMA6UL2L SoM on top of a MBa6ulxl baseboard. The
imxcfg header is for the LGA variant, the downstream U-Boot has an ifdef
for another "standard" variant, however this is not included here since
I don't have hardware to test.
Signed-off-by: Rouven Czerwinski <r.czerwinski at pengutronix.de>
---
v2->v3:
- replace explicit pinmux with comment
v1->v2:
- split up barebox and kernel dts
- fixed DEBUG_LL
- removed mmc0/1 alias switch
- add environment handling
- add MAC handling
- add default update handler
arch/arm/boards/Makefile | 1 +
arch/arm/boards/tqma6ulx/Makefile | 2 +
arch/arm/boards/tqma6ulx/board.c | 43 +++
.../flash-header-imx6ul-tqma6ulx.imxcfg | 102 ++++++
arch/arm/boards/tqma6ulx/lowlevel.c | 55 +++
arch/arm/dts/Makefile | 1 +
arch/arm/dts/imx6ul-mba6ulx.dts | 70 ++++
arch/arm/dts/imx6ul-mba6ulx.dtsi | 333 ++++++++++++++++++
arch/arm/dts/imx6ul-tqma6ulx.dtsi | 80 +++++
arch/arm/dts/tqma6ul-common.dtsi | 191 ++++++++++
arch/arm/dts/tqma6ulx-common.dtsi | 28 ++
arch/arm/mach-imx/Kconfig | 5 +
images/Makefile.imx | 2 +
13 files changed, 913 insertions(+)
create mode 100644 arch/arm/boards/tqma6ulx/Makefile
create mode 100644 arch/arm/boards/tqma6ulx/board.c
create mode 100644 arch/arm/boards/tqma6ulx/flash-header-imx6ul-tqma6ulx.imxcfg
create mode 100644 arch/arm/boards/tqma6ulx/lowlevel.c
create mode 100644 arch/arm/dts/imx6ul-mba6ulx.dts
create mode 100644 arch/arm/dts/imx6ul-mba6ulx.dtsi
create mode 100644 arch/arm/dts/imx6ul-tqma6ulx.dtsi
create mode 100644 arch/arm/dts/tqma6ul-common.dtsi
create mode 100644 arch/arm/dts/tqma6ulx-common.dtsi
diff --git a/arch/arm/boards/Makefile b/arch/arm/boards/Makefile
index 6fe1b59914..c8eebf0674 100644
--- a/arch/arm/boards/Makefile
+++ b/arch/arm/boards/Makefile
@@ -150,6 +150,7 @@ obj-$(CONFIG_MACH_KINDLE_MX50) += kindle-mx50/
obj-$(CONFIG_MACH_TORADEX_COLIBRI_T20) += toradex-colibri-t20/
obj-$(CONFIG_MACH_TOSHIBA_AC100) += toshiba-ac100/
obj-$(CONFIG_MACH_TQMA53) += tqma53/
+obj-$(CONFIG_MACH_TQMA6UL) += tqma6ulx/
obj-$(CONFIG_MACH_TQMA6X) += tqma6x/
obj-$(CONFIG_MACH_TURRIS_OMNIA) += turris-omnia/
obj-$(CONFIG_MACH_TX25) += karo-tx25/
diff --git a/arch/arm/boards/tqma6ulx/Makefile b/arch/arm/boards/tqma6ulx/Makefile
new file mode 100644
index 0000000000..01c7a259e9
--- /dev/null
+++ b/arch/arm/boards/tqma6ulx/Makefile
@@ -0,0 +1,2 @@
+obj-y += board.o
+lwl-y += lowlevel.o
diff --git a/arch/arm/boards/tqma6ulx/board.c b/arch/arm/boards/tqma6ulx/board.c
new file mode 100644
index 0000000000..06b5e1322c
--- /dev/null
+++ b/arch/arm/boards/tqma6ulx/board.c
@@ -0,0 +1,43 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2021 Rouven Czerwinski, Pengutronix
+ */
+
+#include <common.h>
+#include <bootsource.h>
+#include <init.h>
+#include <mach/generic.h>
+#include <mach/bbu.h>
+#include <of.h>
+#include <string.h>
+
+static int mba6ulx_probe(struct device_d *dev)
+{
+ int flags;
+
+ /* the bootloader is stored in one of the two boot partitions */
+ flags = bootsource_get_instance() == 0 ? BBU_HANDLER_FLAG_DEFAULT : 0;
+ imx6_bbu_internal_mmc_register_handler("SD", "/dev/mmc0.barebox", flags);
+
+ flags = bootsource_get_instance() == 1 ? BBU_HANDLER_FLAG_DEFAULT : 0;
+ imx6_bbu_internal_mmcboot_register_handler("eMMC", "/dev/mmc1", flags);
+
+ if (bootsource_get_instance() == 0)
+ of_device_enable_path("/chosen/environment-sd");
+ else
+ of_device_enable_path("/chosen/environment-emmc");
+
+ return 0;
+}
+
+static const struct of_device_id mba6ulx_of_match[] = {
+ { .compatible = "tq,mba6ulx" },
+ { /* sentinel */ },
+};
+
+static struct driver_d mba6ulx_board_driver = {
+ .name = "board-mba6ulx",
+ .probe = mba6ulx_probe,
+ .of_compatible = mba6ulx_of_match,
+};
+device_platform_driver(mba6ulx_board_driver);
diff --git a/arch/arm/boards/tqma6ulx/flash-header-imx6ul-tqma6ulx.imxcfg b/arch/arm/boards/tqma6ulx/flash-header-imx6ul-tqma6ulx.imxcfg
new file mode 100644
index 0000000000..4f71136149
--- /dev/null
+++ b/arch/arm/boards/tqma6ulx/flash-header-imx6ul-tqma6ulx.imxcfg
@@ -0,0 +1,102 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+loadaddr 0x80000000
+soc imx6
+ivtofs 0x400
+
+/* Enable all clocks */
+wm 32 0x020c4068 0xffffffff
+wm 32 0x020c406c 0xffffffff
+wm 32 0x020c4070 0xffffffff
+wm 32 0x020c4074 0xffffffff
+wm 32 0x020c4078 0xffffffff
+wm 32 0x020c407c 0xffffffff
+wm 32 0x020c4080 0xffffffff
+
+/* This flash header contains support for the LGA Variant */
+/*
+ * =====================================================================
+ * IOMUX
+ * =====================================================================
+ */
+/* DDR IO TYPE: */
+wm 32 0x020E04B4 0x000C0000 /* IOMUXC_SW_PAD_CTL_GRP_DDR_TYPE */
+wm 32 0x020E04AC 0x00000000 /* IOMUXC_SW_PAD_CTL_GRP_DDRPKE */
+/* CLOCK: */
+wm 32 0x020E027C 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDCLK0_P */
+/* Control: */
+wm 32 0x020E0250 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_CAS */
+wm 32 0x020E024C 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_RAS */
+wm 32 0x020E0490 0x00000030 /* IOMUXC_SW_PAD_CTL_GRP_ADDDS */
+wm 32 0x020E0288 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_RESET */
+wm 32 0x020E0270 0x00000000 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDBA2 - DSE can be configured using Group Control Register: IOMUXC_SW_PAD_CTL_GRP_CTLDS */
+wm 32 0x020E0260 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_ODT0 */
+wm 32 0x020E0264 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_ODT1 */
+wm 32 0x020E04A0 0x00000030 /* IOMUXC_SW_PAD_CTL_GRP_CTLDS */
+/* Data Strobes: */
+wm 32 0x020E0494 0x00020000 /* IOMUXC_SW_PAD_CTL_GRP_DDRMODE_CTL */
+wm 32 0x020E0280 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS0_P */
+wm 32 0x020E0284 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS1_P */
+/* Data: */
+wm 32 0x020E04B0 0x00020000 /* IOMUXC_SW_PAD_CTL_GRP_DDRMODE */
+wm 32 0x020E0498 0x00000030 /* IOMUXC_SW_PAD_CTL_GRP_B0DS */
+wm 32 0x020E04A4 0x00000030 /* IOMUXC_SW_PAD_CTL_GRP_B1DS */
+wm 32 0x020E0244 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_DQM0 */
+wm 32 0x020E0248 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_DQM1 */
+/*
+ * =====================================================================
+ * DDR Controller Registers
+ * =====================================================================
+ */
+wm 32 0x021B001C 0x00008000 /* MMDC_MDSCR - MMDC Core Special Command Register */
+/*
+ * ======================================================
+ * Calibrations:
+ * ======================================================
+ */
+wm 32 0x021B0800 0xA1390003 /* DDR_PHY_P0_MPZQHWCTRL , enable both one-time & periodic HW ZQ calibration. */
+
+wm 32 0x021B080C 0x00130003 /* MMDC_MPWLDECTRL0 */
+wm 32 0x021B083C 0x41540154 /* MMDC_MPDGCTRL0 */
+wm 32 0x021B0848 0x40405050 /* MMDC_MPRDDLCTL */
+wm 32 0x021B0850 0x40404E4C /* MMDC_MPWRDLCTL */
+wm 32 0x021B081C 0x33333333 /* MMDC_MPRDDQBY0DL */
+wm 32 0x021B0820 0x33333333 /* MMDC_MPRDDQBY1DL */
+wm 32 0x021B082C 0xf3333333 /* MMDC_MPWRDQBY0DL */
+wm 32 0x021B0830 0xf3333333 /* MMDC_MPWRDQBY1DL */
+wm 32 0x021B08C0 0x00921012 /* MMDC_MPDCCR */
+
+/* Complete calibration by forced measurement: */
+wm 32 0x021B08b8 0x00000800 /* DDR_PHY_P0_MPMUR0, frc_msr */
+
+/*
+ * =====================================================================
+ * MMDC init:
+ * =====================================================================
+ */
+wm 32 0x021B0004 0x0002002D /* MMDC0_MDPDC */
+wm 32 0x021B0008 0x00333030 /* MMDC0_MDOTC */
+wm 32 0x021B000C 0x676B52F3 /* MMDC0_MDCFG0 */
+wm 32 0x021B0010 0xB66D8B63 /* MMDC0_MDCFG1 */
+wm 32 0x021B0014 0x01FF00DB /* MMDC0_MDCFG2 */
+wm 32 0x021B0018 0x00201740 /* MMDC0_MDMISC */
+/* TODO: set configuration request again, also done by NXP */
+wm 32 0x021B001C 0x00008000 /* MMDC_MDSCR */
+wm 32 0x021B002C 0x000026D2 /* MMDC0_MDRWD; recommend to maintain the default values */
+wm 32 0x021B0030 0x006B1023 /* MMDC0_MDOR */
+wm 32 0x021B0040 0x00000047 /* CS0_END */
+wm 32 0x021B0000 0x83180000 /* MMDC0_MDCTL */
+/* Mode register writes for CS0 */
+wm 32 0x021B001C 0x02008032 /* MMDC0_MDSCR, MR2 write, CS0 */
+wm 32 0x021B001C 0x00008033 /* MMDC0_MDSCR, MR3 write, CS0 */
+wm 32 0x021B001C 0x00048031 /* MMDC0_MDSCR, MR1 write, CS0 */
+wm 32 0x021B001C 0x15208030 /* MMDC0_MDSCR, MR0 write, CS0 */
+wm 32 0x021B001C 0x04008040 /* MMDC0_MDSCR, ZQ calibration command sent to device on CS0 */
+/* Mode register writes for CS1, not used / needed */
+/* final DDR setup, before operation start: */
+wm 32 0x021B0020 0x00000800 /* MMDC0_MDREF */
+wm 32 0x021B0818 0x00000227 /* DDR_PHY_P0_MPODTCTRL */
+wm 32 0x021B0004 0x0002552D /* MMDC0_MDPDC now SDCTL power down enabled */
+wm 32 0x021B0404 0x00011006 /* MMDC0_MAPSR ADOPT power down enabled */
+wm 32 0x021B001C 0x00000000 /* MMDC0_MDSCR, clear this register (especially the configuration bit as initialization is complete) */
+
+#include <mach/habv4-imx6-gencsf.h>
diff --git a/arch/arm/boards/tqma6ulx/lowlevel.c b/arch/arm/boards/tqma6ulx/lowlevel.c
new file mode 100644
index 0000000000..db77d1f532
--- /dev/null
+++ b/arch/arm/boards/tqma6ulx/lowlevel.c
@@ -0,0 +1,55 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2019 Rouven Czerwinski, Pengutronix
+ */
+
+#include <common.h>
+#include <debug_ll.h>
+#include <firmware.h>
+#include <mach/generic.h>
+#include <asm/barebox-arm.h>
+#include <mach/esdctl.h>
+#include <mach/iomux-mx6ul.h>
+#include <asm/cache.h>
+
+extern char __dtb_z_imx6ul_mba6ulx_start[];
+
+static void setup_uart(void)
+{
+ imx6_ungate_all_peripherals();
+
+ /*
+ * Default pad configuration on this board, no explicit config needed
+ */
+ imx6_uart_setup((void *)MX6_UART1_BASE_ADDR);
+ pbl_set_putc(imx_uart_putc, (void *)MX6_UART1_BASE_ADDR);
+
+ pr_debug("\n");
+
+}
+
+static void noinline start_mba6ulx(void)
+{
+ setup_uart();
+
+ imx6ul_barebox_entry(__dtb_z_imx6ul_mba6ulx_start);
+}
+
+ENTRY_FUNCTION(start_imx6ul_mba6ulx, r0, r1, r2)
+{
+
+ imx6ul_cpu_lowlevel_init();
+
+ arm_setup_stack(0x00910000);
+
+ if (IS_ENABLED(CONFIG_DEBUG_LL)) {
+ imx6_uart_setup_ll();
+ putc_ll('>');
+ }
+
+ relocate_to_current_adr();
+ setup_c();
+ barrier();
+
+ start_mba6ulx();
+}
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 8ae8244bfe..8cca17ba57 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -139,6 +139,7 @@ lwl-$(CONFIG_MACH_NXP_IMX8MQ_EVK) += imx8mq-evk.dtb.o
lwl-$(CONFIG_MACH_TORADEX_COLIBRI_T20) += tegra20-colibri-iris.dtb.o
lwl-$(CONFIG_MACH_TOSHIBA_AC100) += tegra20-paz00.dtb.o
lwl-$(CONFIG_MACH_TQMA53) += imx53-mba53.dtb.o
+lwl-$(CONFIG_MACH_TQMA6UL) += imx6ul-mba6ulx.dtb.o
lwl-$(CONFIG_MACH_TQMA6X) += imx6dl-mba6x.dtb.o imx6q-mba6x.dtb.o
lwl-$(CONFIG_MACH_TX25) += imx25-karo-tx25.dtb.o
lwl-$(CONFIG_MACH_TX6X) += imx6dl-tx6u.dtb.o
diff --git a/arch/arm/dts/imx6ul-mba6ulx.dts b/arch/arm/dts/imx6ul-mba6ulx.dts
new file mode 100644
index 0000000000..e2ed694ff9
--- /dev/null
+++ b/arch/arm/dts/imx6ul-mba6ulx.dts
@@ -0,0 +1,70 @@
+
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2021 Pengutronix e.K.
+ * Author: Rouven Czerwinski
+ */
+
+/dts-v1/;
+
+#include "imx6ul-mba6ulx.dtsi"
+
+/ {
+ chosen {
+ environment-sd {
+ compatible = "barebox,environment";
+ device-path = &environment_sd;
+ status = "disabled";
+ };
+ environment-emmc {
+ compatible = "barebox,environment";
+ device-path = &environment_emmc;
+ status = "disabled";
+ };
+ };
+};
+
+&usdhc2 {
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "barebox";
+ reg = <0x0 0xe0000>;
+ };
+
+ environment_emmc: partition at e0000 {
+ label = "barebox-environment";
+ reg = <0xe0000 0x20000>;
+ };
+ };
+};
+
+&usdhc1 {
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "barebox";
+ reg = <0x0 0xe0000>;
+ };
+
+ environment_sd: partition at e0000 {
+ label = "barebox-environment";
+ reg = <0xe0000 0x20000>;
+ };
+ };
+};
+
+&ocotp {
+ barebox,provide-mac-address = <&fec1 0x620 &fec2 0x632>;
+};
+
+/* include the FIT public key for verifying on demand */
+#ifdef CONFIG_BOOTM_FITIMAGE_PUBKEY
+#include CONFIG_BOOTM_FITIMAGE_PUBKEY
+#endif
diff --git a/arch/arm/dts/imx6ul-mba6ulx.dtsi b/arch/arm/dts/imx6ul-mba6ulx.dtsi
new file mode 100644
index 0000000000..da73248084
--- /dev/null
+++ b/arch/arm/dts/imx6ul-mba6ulx.dtsi
@@ -0,0 +1,333 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2016 TQ Systems GmbH
+ * Author: Marco Felsch
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include "imx6ul-tqma6ulx.dtsi"
+
+/ {
+ model = "TQ TQMa6ULx SoM on MBa6ULx";
+ compatible = "tq,mba6ulx", "tq,imx6ul-tqma6ul2l", "fsl,imx6ul";
+
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ reg_mba6ul_3v3: regulator-mba6ul-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "supply-mba6ul-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_mba6ul_5v0: regulator-mba6ul-5v0 {
+ compatible = "regulator-fixed";
+ regulator-name = "supply-mba6ul-5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ reg_otg2vbus_5v0: regulator-otg2-vbus-5v0 {
+ compatible = "regulator-fixed";
+ gpio = <&gpio3 21 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-name = "otg2-vbus-supply-5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <®_mba6ul_5v0>;
+ };
+
+ reg_otg1vbus_5v0: regulator-otg1-vbus-5v0 {
+ compatible = "regulator-fixed";
+ gpio = <&gpio1 4 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-name = "otg1-vbus-supply-5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <®_mba6ul_5v0>;
+ };
+
+ reg_fec_3v3: regulator-fec-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "fec-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ vin-supply = <®_mba6ul_3v3>;
+ };
+
+ reg_mpcie: regulator-mpcie-1v5 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ regulator-name = "mpcie-1v5";
+ /* gpio = <&gpio1 3 GPIO_ACTIVE_HIGH>; */
+ enable-active-high;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ vin-supply = <®_mba6ul_3v3>;
+ };
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet1>;
+ phy-mode = "rmii";
+ phy-handle = <ðphy0>;
+ phy-supply = <®_fec_3v3>;
+ phy-reset-gpios = <&gpio3 9 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <26>;
+ status = "okay";
+};
+
+&fec2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet2>;
+ phy-mode = "rmii";
+ phy-handle = <ðphy1>;
+ phy-supply = <®_fec_3v3>;
+ phy-reset-gpios = <&gpio3 10 GPIO_ACTIVE_HIGH>;
+ phy-reset-duration = <26>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy at 0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ max-speed = <100>;
+ reg = <0>;
+ /* ToDo: check if following 2 lines are required */
+ clocks = <&clks IMX6UL_CLK_ENET_REF>;
+ clock-names = "rmii-ref";
+ };
+
+ ethphy1: ethernet-phy at 1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ max-speed = <100>;
+ reg = <1>;
+ /* ToDo: check if following 2 lines are required */
+ clocks = <&clks IMX6UL_CLK_ENET2_REF>;
+ clock-names = "rmii-ref";
+ };
+ };
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ expander_io: gpio-expander at 20 {
+ compatible = "nxp,pca9554";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ status = "okay";
+ };
+
+ expander_in: gpio-expander at 21 {
+ compatible = "nxp,pca9554";
+ reg = <0x21>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_expander_irq>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ status = "okay";
+ };
+
+ expander_out: gpio-expander at 22 {
+ compatible = "nxp,pca9554";
+ reg = <0x22>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ status = "okay";
+ };
+
+
+ /* NXP SE97BTP with temperature sensor + eeprom */
+ jc42_1b: eeprom-temperature-sensor at 1b {
+ compatible = "nxp,se97", "jedec,jc-42.4-temp";
+ reg = <0x1b>;
+ status = "okay";
+ };
+
+ se97_53: eeprom-temperature-sensor at 53 {
+ compatible = "nxp,spd";
+ reg = <0x53>;
+ pagesize = <16>;
+ status = "okay";
+ };
+
+};
+
+
+&iomuxc {
+ pinctrl-names = "default";
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_DATA00__I2C3_SDA 0x4001b8b0
+ MX6UL_PAD_LCD_DATA01__I2C3_SCL 0x4001b8b0
+ >;
+ };
+
+ pinctrl_enet1: enet1grp {
+ fsl,pins = <
+ MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x1b0b0
+ MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0
+ MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0
+ MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0
+ MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0
+ MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0
+ MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b0b0
+ MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4001b0a8
+ >;
+ };
+
+ pinctrl_enet2: enet2grp {
+ fsl,pins = <
+ MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN 0x1b0b0
+ MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER 0x1b0b0
+ MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x1b0b0
+ MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x1b0b0
+ MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x1b0a0
+ MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x1b0a0
+ MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN 0x1b0b0
+ MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x4001b0a8
+ /* mdio */
+ MX6UL_PAD_GPIO1_IO07__ENET2_MDC 0x1b0b0
+ MX6UL_PAD_GPIO1_IO06__ENET2_MDIO 0x1b0b0
+ >;
+ };
+
+ pinctrl_expander_irq: expanderirqgrp {
+ fsl,pins = <
+ MX6UL_PAD_SNVS_TAMPER8__GPIO5_IO08 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1
+ MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_usb_otg1: usbotg1grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID 0x00017059
+ MX6UL_PAD_GPIO1_IO01__USB_OTG1_OC 0x0001b0b0
+ /* PWR */
+ MX6UL_PAD_GPIO1_IO04__GPIO1_IO04 0x0001b099
+ >;
+ };
+
+ pinctrl_usb_otg2: usbotg2grp {
+ fsl,pins = <
+ /* reset */
+ MX6UL_PAD_LCD_DATA16__GPIO3_IO21 0x0001b099
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x00017069
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x00017059
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x00017059
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x00017059
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x00017059
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x00017059
+ /* CD */
+ MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x0001b099
+ >;
+ };
+
+ pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x00017069
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x000170b9
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x000170b9
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x000170b9
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x000170b9
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x000170b9
+ /* CD */
+ MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x0001b099
+ >;
+ };
+
+ pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x00017069
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x000170f9
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x000170f9
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x000170f9
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x000170f9
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x000170f9
+ /* CD */
+ MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x0001b099
+ >;
+ };
+
+ pinctrl_wdog1: wdog1grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO08__WDOG1_WDOG_B 0x0001b099
+ >;
+ };
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+/* otg-port */
+&usbotg1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_otg1>;
+ vbus-supply = <®_otg1vbus_5v0>;
+ dr_mode = "otg";
+ status = "okay";
+};
+
+/* 7-port usb hub */
+/* id, pwr, oc pins not connected */
+&usbotg2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_otg2>;
+ disable-over-current;
+ vbus-supply = <®_otg2vbus_5v0>;
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ bus-width = <4>;
+ vmmc-supply = <®_mba6ul_3v3>;
+ vqmmc-supply = <®_vccsd>;
+ no-1-8-v;
+ status = "okay";
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog1>;
+ fsl,ext-reset-output;
+ status = "okay";
+};
diff --git a/arch/arm/dts/imx6ul-tqma6ulx.dtsi b/arch/arm/dts/imx6ul-tqma6ulx.dtsi
new file mode 100644
index 0000000000..77112e1974
--- /dev/null
+++ b/arch/arm/dts/imx6ul-tqma6ulx.dtsi
@@ -0,0 +1,80 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018 TQ Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel at tq-group.com>
+ */
+
+#include <arm/imx6ul.dtsi>
+#include "tqma6ul-common.dtsi"
+#include "tqma6ulx-common.dtsi"
+
+/ {
+ model = "TQMa6ULx SOM";
+};
+
+&cpu0 {
+ cooling-min-level = <0>;
+ cooling-max-level = <3>;
+ #cooling-cells = <2>;
+};
+
+&iomuxc {
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x00017051
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x00017051
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x00017051
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x00017051
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x00017051
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x00017051
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x00017051
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x00017051
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x00017051
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x00017051
+ /* rst */
+ MX6UL_PAD_NAND_ALE__GPIO4_IO10 0x0001b051
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2grp_100mhz {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x000170e1
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x000170f1
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x000170f1
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x000170f1
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x000170f1
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x000170f1
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x000170f1
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x000170f1
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x000170f1
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x000170f1
+ /* rst */
+ MX6UL_PAD_NAND_ALE__GPIO4_IO10 0x0001b051
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2grp_200mhz {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x000170f1
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x000170e1
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x000170e1
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x000170e1
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x000170e1
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x000170e1
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x000170e1
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x000170e1
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x000170e1
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x000170e1
+ /* rst */
+ MX6UL_PAD_NAND_ALE__GPIO4_IO10 0x0001b051
+ >;
+ };
+};
+
+&usdhc2 {
+ fsl,tuning-step= <6>;
+ max-frequency = <99000000>;
+ assigned-clocks = <&clks IMX6UL_CLK_USDHC2_SEL>, <&clks IMX6UL_CLK_USDHC2>;
+ assigned-clock-parents = <&clks IMX6UL_CLK_PLL2_PFD2>;
+ assigned-clock-rates = <0>, <198000000>;
+};
diff --git a/arch/arm/dts/tqma6ul-common.dtsi b/arch/arm/dts/tqma6ul-common.dtsi
new file mode 100644
index 0000000000..92b295891c
--- /dev/null
+++ b/arch/arm/dts/tqma6ul-common.dtsi
@@ -0,0 +1,191 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018 TQ Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel at tq-group.com>
+ */
+
+&cpu0 {
+ arm-supply = <®_arm>;
+ soc-supply = <®_soc>;
+};
+
+&i2c4 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c4>;
+ status = "okay";
+
+ pfuze3000: pmic at 8 {
+ compatible = "fsl,pfuze3000";
+ reg = <0x08>;
+
+ regulators {
+ reg_sw1a: sw1a {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-ramp-delay = <6250>;
+ /* not used */
+ };
+
+ reg_sw1b_core: sw1b {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1475000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ reg_sw2: sw2 {
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+
+ reg_sw3_ddr: sw3 {
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1650000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_swbst: swbst {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5150000>;
+ /* not used */
+ };
+
+ reg_snvs_3v0: vsnvs {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_vrefddr: vrefddr {
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_vccsd: vccsd {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reg_v33_3v3: v33 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_vldo1_3v3: vldo1 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ /* not used */
+ };
+
+ reg_vldo2: vldo2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ regulator-boot-on;
+ /* not used */
+ };
+
+ reg_vldo3: vldo3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ /* not used */
+ };
+
+ reg_vldo4: vldo4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-fixed;
+ regulator-always-on;
+ };
+ };
+ };
+
+ jc42_1a: eeprom-temperature-sensor at 1a {
+ compatible = "nxp,se97", "jedec,jc-42.4-temp";
+ reg = <0x1a>;
+ status = "okay";
+ };
+
+ m24c64_50: eeprom at 50 {
+ compatible = "atmel,24c64";
+ reg = <0x50>;
+ pagesize = <32>;
+ status = "okay";
+ };
+
+ m24c02_52: eeprom at 52 {
+ compatible = "atmel,24c02";
+ reg = <0x52>;
+ pagesize = <16>;
+ status = "okay";
+ };
+
+ rtc1: rtc at 68 {
+ compatible = "dallas,ds1339";
+ reg = <0x68>;
+ status = "okay";
+ };
+};
+
+&iomuxc {
+ pinctrl_i2c4: i2c4grp {
+ fsl,pins = <
+ MX6UL_PAD_UART2_TX_DATA__I2C4_SCL 0x4001b8b0
+ MX6UL_PAD_UART2_RX_DATA__I2C4_SDA 0x4001b8b0
+ >;
+ };
+
+ /*
+ * currently not used, potentially dangerous if used on
+ * baseboard
+ */
+ pinctrl_pmic: pmic {
+ fsl,pins = <
+ /* PMIC irq */
+ MX6UL_PAD_CSI_DATA03__GPIO4_IO24 0x1b099
+ >;
+ };
+};
+
+&qspi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_qspi>;
+ status = "okay";
+
+ flash0: spinor at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ spi-max-frequency = <33000000>;
+ spi-rx-bus-width = <4>;
+ spi-tx-bus-width = <4>;
+ reg = <0>;
+ };
+};
+
+&snvs_rtc {
+ status = "disabled";
+};
+
+/* eMMC */
+&usdhc2 {
+ pinctrl-names = "default", "state_100mhz" , "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+
+ bus-width = <8>;
+ disable-wp;
+ non-removable;
+ no-sdio;
+ no-sd;
+ status = "okay";
+};
diff --git a/arch/arm/dts/tqma6ulx-common.dtsi b/arch/arm/dts/tqma6ulx-common.dtsi
new file mode 100644
index 0000000000..3e398d25ad
--- /dev/null
+++ b/arch/arm/dts/tqma6ulx-common.dtsi
@@ -0,0 +1,28 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018 TQ Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel at tq-group.com>
+ */
+
+&iomuxc {
+ pinctrl_qspi: qspigrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_WP_B__QSPI_A_SCLK 0x70b9
+ MX6UL_PAD_NAND_READY_B__QSPI_A_DATA00 0x70b9
+ MX6UL_PAD_NAND_CE0_B__QSPI_A_DATA01 0x70b9
+ MX6UL_PAD_NAND_CE1_B__QSPI_A_DATA02 0x70b9
+ MX6UL_PAD_NAND_CLE__QSPI_A_DATA03 0x70b9
+ MX6UL_PAD_NAND_DQS__QSPI_A_SS0_B 0x70a1
+ >;
+ };
+};
+
+®_sw2 {
+ regulator-always-on;
+};
+
+/* eMMC */
+&usdhc2 {
+ vmmc-supply = <®_sw2>;
+ vqmmc-supply = <®_vldo4>;
+};
diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig
index 454f7328d8..6b962dcf7e 100644
--- a/arch/arm/mach-imx/Kconfig
+++ b/arch/arm/mach-imx/Kconfig
@@ -391,6 +391,11 @@ config MACH_TQMA6X
bool "TQ tqma6x on mba6x"
select ARCH_IMX6
+config MACH_TQMA6UL
+ bool "TQ tqma6ul on mba6ulx"
+ select ARCH_IMX6UL
+ select ARM_USE_COMPRESSED_DTB
+
config MACH_TX6X
bool "Karo TX6x"
select ARCH_IMX6
diff --git a/images/Makefile.imx b/images/Makefile.imx
index 1dffab989e..18cabbf041 100644
--- a/images/Makefile.imx
+++ b/images/Makefile.imx
@@ -180,6 +180,8 @@ $(call build_imx_habv4img, CONFIG_MACH_TQMA6X, start_imx6dl_mba6x, tqma6x/flash-
$(call build_imx_habv4img, CONFIG_MACH_TQMA6X, start_imx6q_mba6x, tqma6x/flash-header-tqma6q, tq-tqma6q-mba6x)
+$(call build_imx_habv4img, CONFIG_MACH_TQMA6UL, start_imx6ul_mba6ulx, tqma6ulx/flash-header-imx6ul-tqma6ulx, tq-tqma6ul-mba6ulx)
+
$(call build_imx_habv4img, CONFIG_MACH_PHYTEC_SOM_IMX6, start_phytec_pbab01_4gib, phytec-som-imx6/flash-header-phytec-pfla02-4gib, phytec-pbab01-4gib)
$(call build_imx_habv4img, CONFIG_MACH_PHYTEC_SOM_IMX6, start_phytec_pbab01_2gib, phytec-som-imx6/flash-header-phytec-pfla02-2gib, phytec-pbab01-2gib)
--
2.30.2
More information about the barebox
mailing list