[PATCH v3] ARM: Rockchip: Add rk3568 BananaPi R2 Pro board support
Frank Wunderlich
linux at fw-web.de
Fri Feb 11 01:13:54 PST 2022
From: Frank Wunderlich <frank-w at public-files.de>
This adds support for the BananaPi R2 Pro board.
It is basicly a copy of rk3568 evb board but with slightly modified DTS.
Added GPIO-Leds to dts and modified the hw-detection a bit.
Tested features so far are:
- 1st stage booting
- Network
- SD card and Emmc
- usb (1.1 and 3 work, usb2 not working)
- power LED (green)
Signed-off-by: Frank Wunderlich <frank-w at public-files.de>
---
changes in v3:
- modify to be more similar to linux dts
changes in v2:
- dts: drop chosen label
- some changes to dts to make it similar to linux-version
- board.c: add "bpi" on different places and drop rk3568 partially
- drop change in dt-bindings
- add entry to Documentation rk356x supported boards
- add bpi-r2-pro to rockchip_v8_defconfig
---
Documentation/boards/rockchip.rst | 1 +
arch/arm/boards/Makefile | 1 +
.../rockchip-rk3568-bpi-r2pro/.gitignore | 1 +
.../boards/rockchip-rk3568-bpi-r2pro/Makefile | 2 +
.../boards/rockchip-rk3568-bpi-r2pro/board.c | 93 +++
.../rockchip-rk3568-bpi-r2pro/lowlevel.c | 49 ++
arch/arm/configs/rockchip_v8_defconfig | 1 +
arch/arm/dts/Makefile | 1 +
arch/arm/dts/rk3568-bpi-r2-pro.dts | 593 ++++++++++++++++++
arch/arm/mach-rockchip/Kconfig | 6 +
images/Makefile.rockchip | 7 +
11 files changed, 755 insertions(+)
create mode 100644 arch/arm/boards/rockchip-rk3568-bpi-r2pro/.gitignore
create mode 100644 arch/arm/boards/rockchip-rk3568-bpi-r2pro/Makefile
create mode 100644 arch/arm/boards/rockchip-rk3568-bpi-r2pro/board.c
create mode 100644 arch/arm/boards/rockchip-rk3568-bpi-r2pro/lowlevel.c
create mode 100644 arch/arm/dts/rk3568-bpi-r2-pro.dts
diff --git a/Documentation/boards/rockchip.rst b/Documentation/boards/rockchip.rst
index 68c3e112650b..041bb9fa6490 100644
--- a/Documentation/boards/rockchip.rst
+++ b/Documentation/boards/rockchip.rst
@@ -57,6 +57,7 @@ Supported Boards
----------------
- Rockchip RK3568 EVB
+- Rockchip RK3568 Bananapi R2 Pro
- Pine64 Quartz64 Model A
The steps described in the following target the RK3568 and the RK3568 EVB but
diff --git a/arch/arm/boards/Makefile b/arch/arm/boards/Makefile
index 6fe1b5991455..0ede7818fdde 100644
--- a/arch/arm/boards/Makefile
+++ b/arch/arm/boards/Makefile
@@ -186,4 +186,5 @@ obj-$(CONFIG_MACH_TQMLS1046A) += tqmls1046a/
obj-$(CONFIG_MACH_MNT_REFORM) += mnt-reform/
obj-$(CONFIG_MACH_SKOV_ARM9CPU) += skov-arm9cpu/
obj-$(CONFIG_MACH_RK3568_EVB) += rockchip-rk3568-evb/
+obj-$(CONFIG_MACH_RK3568_BPI_R2PRO) += rockchip-rk3568-bpi-r2pro/
obj-$(CONFIG_MACH_PINE64_QUARTZ64) += pine64-quartz64/
diff --git a/arch/arm/boards/rockchip-rk3568-bpi-r2pro/.gitignore b/arch/arm/boards/rockchip-rk3568-bpi-r2pro/.gitignore
new file mode 100644
index 000000000000..f458f794b54c
--- /dev/null
+++ b/arch/arm/boards/rockchip-rk3568-bpi-r2pro/.gitignore
@@ -0,0 +1 @@
+sdram-init.bin
diff --git a/arch/arm/boards/rockchip-rk3568-bpi-r2pro/Makefile b/arch/arm/boards/rockchip-rk3568-bpi-r2pro/Makefile
new file mode 100644
index 000000000000..01c7a259e9a5
--- /dev/null
+++ b/arch/arm/boards/rockchip-rk3568-bpi-r2pro/Makefile
@@ -0,0 +1,2 @@
+obj-y += board.o
+lwl-y += lowlevel.o
diff --git a/arch/arm/boards/rockchip-rk3568-bpi-r2pro/board.c b/arch/arm/boards/rockchip-rk3568-bpi-r2pro/board.c
new file mode 100644
index 000000000000..e472f13c8bbf
--- /dev/null
+++ b/arch/arm/boards/rockchip-rk3568-bpi-r2pro/board.c
@@ -0,0 +1,93 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#define pr_fmt(fmt) "rk3568-r2pro: " fmt
+
+#include <common.h>
+#include <init.h>
+#include <mach/bbu.h>
+#include <aiodev.h>
+#include <bootsource.h>
+#include <environment.h>
+#include <globalvar.h>
+#include <magicvar.h>
+#include <deep-probe.h>
+
+static bool machine_is_bpi_r2pro = false;
+
+static int rk3568_bpi_r2pro_probe(struct device_d *dev)
+{
+ enum bootsource bootsource = bootsource_get();
+ int instance = bootsource_get_instance();
+
+ barebox_set_model("BPI R2PRO");
+ barebox_set_hostname("bpi-r2pro");
+ machine_is_bpi_r2pro = true;
+
+ if (bootsource == BOOTSOURCE_MMC && instance == 1)
+ of_device_enable_path("/chosen/environment-sd");
+ else
+ of_device_enable_path("/chosen/environment-emmc");
+
+ rk3568_bbu_mmc_register("emmc", BBU_HANDLER_FLAG_DEFAULT, "/dev/emmc");
+ rk3568_bbu_mmc_register("sd", 0, "/dev/sd");
+
+ return 0;
+}
+
+static const struct of_device_id rk3568_bpi_r2pro_of_match[] = {
+ { .compatible = "rockchip,rk3568-bpi-r2pro" },
+ { /* Sentinel */},
+};
+
+static struct driver_d rk3568_bpi_r2pro_board_driver = {
+ .name = "board-rk3568-bpi-r2pro",
+ .probe = rk3568_bpi_r2pro_probe,
+ .of_compatible = rk3568_bpi_r2pro_of_match,
+};
+coredevice_platform_driver(rk3568_bpi_r2pro_board_driver);
+
+BAREBOX_DEEP_PROBE_ENABLE(rk3568_bpi_r2pro_of_match);
+
+static int rk3568_bpi_r2pro_detect_hwid(void)
+{
+ int ret;
+ int hwid_voltage;
+ struct aiochannel *hwid_chan;
+ char *hwid;
+
+ if (!IS_ENABLED(CONFIG_AIODEV))
+ return 0;
+
+ if (!machine_is_bpi_r2pro)
+ return 0;
+
+ hwid_chan = aiochannel_by_name("aiodev0.in_value1_mV");
+ if (IS_ERR(hwid_chan)) {
+ ret = PTR_ERR(hwid_chan);
+ goto err_hwid;
+ }
+
+ ret = aiochannel_get_value(hwid_chan, &hwid_voltage);
+ if (ret)
+ goto err_hwid;
+
+ pr_info("hwid_voltage: %d\n", hwid_voltage);
+
+ if (hwid_voltage == 1800)
+ hwid = "V00";
+ else
+ hwid = "unknown";
+
+ pr_info("Detected RK3568 BananaPi R2 Pro %s\n", hwid);
+
+ globalvar_add_simple("board.hwid", hwid);
+
+ return 0;
+
+err_hwid:
+ pr_err("couldn't retrieve hardware ID\n");
+ return ret;
+}
+late_initcall(rk3568_bpi_r2pro_detect_hwid);
+
+BAREBOX_MAGICVAR(global.board.hwid, "The board hardware ID");
diff --git a/arch/arm/boards/rockchip-rk3568-bpi-r2pro/lowlevel.c b/arch/arm/boards/rockchip-rk3568-bpi-r2pro/lowlevel.c
new file mode 100644
index 000000000000..9f039c604854
--- /dev/null
+++ b/arch/arm/boards/rockchip-rk3568-bpi-r2pro/lowlevel.c
@@ -0,0 +1,49 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <common.h>
+#include <linux/sizes.h>
+#include <asm/barebox-arm-head.h>
+#include <asm/barebox-arm.h>
+#include <mach/hardware.h>
+#include <mach/atf.h>
+#include <debug_ll.h>
+#include <mach/rockchip.h>
+
+extern char __dtb_rk3568_bpi_r2_pro_start[];
+
+static noinline void rk3568_start(void)
+{
+ void *fdt;
+
+ /*
+ * Enable vccio4 1.8V and vccio6 1.8V
+ * Needed for GMAC to work.
+ */
+ writel(RK_SETBITS(0x50), 0xfdc20140);
+
+ fdt = __dtb_rk3568_bpi_r2_pro_start;
+
+ if (current_el() == 3) {
+ rk3568_lowlevel_init();
+ rk3568_atf_load_bl31(fdt);
+ /* not reached */
+ }
+
+ barebox_arm_entry(RK3568_DRAM_BOTTOM, 0x80000000 - RK3568_DRAM_BOTTOM, fdt);
+}
+
+ENTRY_FUNCTION(start_rk3568_bpi_r2pro, r0, r1, r2)
+{
+ /*
+ * Image execution starts at 0x0, but this is used for ATF and
+ * OP-TEE later, so move away from here.
+ */
+ if (current_el() == 3)
+ relocate_to_adr_full(RK3568_BAREBOX_LOAD_ADDRESS);
+ else
+ relocate_to_current_adr();
+
+ setup_c();
+
+ rk3568_start();
+}
diff --git a/arch/arm/configs/rockchip_v8_defconfig b/arch/arm/configs/rockchip_v8_defconfig
index 4ceb036db6ae..387c9f21d2ff 100644
--- a/arch/arm/configs/rockchip_v8_defconfig
+++ b/arch/arm/configs/rockchip_v8_defconfig
@@ -1,5 +1,6 @@
CONFIG_ARCH_ROCKCHIP=y
CONFIG_MACH_RK3568_EVB=y
+CONFIG_MACH_RK3568_BPI_R2PRO=y
CONFIG_MACH_PINE64_QUARTZ64=y
CONFIG_BOARD_ARM_GENERIC_DT=y
CONFIG_ARM_OPTIMZED_STRING_FUNCTIONS=y
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 8ae8244bfeee..8106360e50dd 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -105,6 +105,7 @@ lwl-$(CONFIG_MACH_RADXA_ROCK) += rk3188-radxarock.dtb.o
lwl-$(CONFIG_MACH_PHYTEC_SOM_RK3288) += rk3288-phycore-som.dtb.o
lwl-$(CONFIG_MACH_REALQ7) += imx6q-dmo-edmqmx6.dtb.o
lwl-$(CONFIG_MACH_RK3568_EVB) += rk3568-evb1-v10.dtb.o
+lwl-$(CONFIG_MACH_RK3568_BPI_R2PRO) += rk3568-bpi-r2-pro.dtb.o
lwl-$(CONFIG_MACH_RPI) += bcm2835-rpi.dtb.o
lwl-$(CONFIG_MACH_RPI2) += bcm2836-rpi-2.dtb.o
lwl-$(CONFIG_MACH_RPI3) += bcm2837-rpi-3.dtb.o
diff --git a/arch/arm/dts/rk3568-bpi-r2-pro.dts b/arch/arm/dts/rk3568-bpi-r2-pro.dts
new file mode 100644
index 000000000000..ef2e0c33e663
--- /dev/null
+++ b/arch/arm/dts/rk3568-bpi-r2-pro.dts
@@ -0,0 +1,593 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Author: Frank Wunderlich <frank-w at public-files.de>
+ *
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include "rk3568.dtsi"
+
+/ {
+ model = "Bananapi-R2 Pro (RK3568) DDR4 Board";
+ compatible = "rockchip,rk3568-bpi-r2pro", "rockchip,rk3568";
+
+ aliases {
+ emmc = &sdhci;
+ sd = &sdmmc0;
+ };
+
+ chosen {
+ stdout-path = "serial2:1500000n8";
+
+ environment-sd {
+ compatible = "barebox,environment";
+ device-path = &environment_sd;
+ status = "disabled";
+ };
+
+ environment-emmc {
+ compatible = "barebox,environment";
+ device-path = &environment_emmc;
+ status = "disabled";
+ };
+ };
+
+ memory at a00000 {
+ device_type = "memory";
+ reg = <0x0 0x00a00000 0x0 0x7f600000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&blue_led_pin &green_led_pin>;
+
+ blue_led: led-0 {
+ color = <LED_COLOR_ID_BLUE>;
+ default-state = "off";
+ function = LED_FUNCTION_STATUS;
+ gpios = <&gpio0 RK_PD6 GPIO_ACTIVE_HIGH>;
+ };
+
+ green_led: led-1 {
+ color = <LED_COLOR_ID_GREEN>;
+ default-state = "on";
+ function = LED_FUNCTION_POWER;
+ gpios = <&gpio0 RK_PD5 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ dc_12v: dc-12v {
+ compatible = "regulator-fixed";
+ regulator-name = "dc_12v";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ };
+
+ vcc3v3_sys: vcc3v3-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&dc_12v>;
+ };
+
+ vcc5v0_sys: vcc5v0-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&dc_12v>;
+ };
+
+ vcc3v3_lcd0_n: vcc3v3-lcd0-n {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_lcd0_n";
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_lcd1_n: vcc3v3-lcd1-n {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_lcd1_n";
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc5v0_host: vcc5v0-host-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_host";
+ enable-active-high;
+ gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vcc5v0_host_en>;
+ regulator-always-on;
+ };
+};
+
+&gmac0 {
+ assigned-clocks = <&cru SCLK_GMAC0_RX_TX>, <&cru SCLK_GMAC0>;
+ assigned-clock-parents = <&cru SCLK_GMAC0_RGMII_SPEED>, <&cru CLK_MAC0_2TOP>;
+ assigned-clock-rates = <0>, <125000000>;
+ clock_in_out = "input";
+ phy-handle = <&rgmii_phy0>;
+ phy-mode = "rgmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac0_miim
+ &gmac0_tx_bus2
+ &gmac0_rx_bus2
+ &gmac0_rgmii_clk
+ &gmac0_rgmii_bus>;
+ snps,reset-gpio = <&gpio3 RK_PB7 GPIO_ACTIVE_LOW>;
+ snps,reset-active-low;
+ /* Reset time is 20ms, 100ms for rtl8211f */
+ snps,reset-delays-us = <0 20000 100000>;
+ tx_delay = <0x3c>;
+ rx_delay = <0x2f>;
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ rk809: pmic at 20 {
+ compatible = "rockchip,rk809";
+ reg = <0x20>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
+ #clock-cells = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int>;
+
+ clock-output-names = "rk808-clkout1", "rk808-clkout2";
+ /* 1: rst regs (default in codes), 0: rst the pmic */
+ pmic-reset-func = <0>;
+
+ rockchip,system-power-controller;
+ vcc1-supply = <&vcc3v3_sys>;
+ vcc2-supply = <&vcc3v3_sys>;
+ vcc3-supply = <&vcc3v3_sys>;
+ vcc4-supply = <&vcc3v3_sys>;
+ vcc5-supply = <&vcc3v3_sys>;
+ vcc6-supply = <&vcc3v3_sys>;
+ vcc7-supply = <&vcc3v3_sys>;
+ vcc8-supply = <&vcc3v3_sys>;
+ vcc9-supply = <&vcc3v3_sys>;
+ wakeup-source;
+
+ regulators {
+ vdd_logic: DCDC_REG1 {
+ regulator-name = "vdd_logic";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-init-microvolt = <900000>;
+ regulator-initial-mode = <0x2>;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_gpu: DCDC_REG2 {
+ regulator-name = "vdd_gpu";
+ regulator-init-microvolt = <900000>;
+ regulator-initial-mode = <0x2>;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-name = "vcc_ddr";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-initial-mode = <0x2>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vdd_npu: DCDC_REG4 {
+ regulator-name = "vdd_npu";
+ regulator-init-microvolt = <900000>;
+ regulator-initial-mode = <0x2>;
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_1v8: DCDC_REG5 {
+ regulator-name = "vcc_1v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda0v9_image: LDO_REG1 {
+ regulator-name = "vdda0v9_image";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda_0v9: LDO_REG2 {
+ regulator-name = "vdda_0v9";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda0v9_pmu: LDO_REG3 {
+ regulator-name = "vdda0v9_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <900000>;
+ };
+ };
+
+ vccio_acodec: LDO_REG4 {
+ regulator-name = "vccio_acodec";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vccio_sd: LDO_REG5 {
+ regulator-name = "vccio_sd";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_pmu: LDO_REG6 {
+ regulator-name = "vcc3v3_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcca_1v8: LDO_REG7 {
+ regulator-name = "vcca_1v8";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcca1v8_pmu: LDO_REG8 {
+ regulator-name = "vcca1v8_pmu";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcca1v8_image: LDO_REG9 {
+ regulator-name = "vcca1v8_image";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_3v3: SWITCH_REG1 {
+ regulator-name = "vcc_3v3";
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc3v3_sd: SWITCH_REG2 {
+ regulator-name = "vcc3v3_sd";
+ regulator-always-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+ };
+};
+
+&i2c5 {
+ /* pin 3 (SDA) + 4 (SCL) of header con2 */
+ status = "disabled";
+};
+
+&mdio0 {
+ rgmii_phy0: ethernet-phy at 0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0x0>;
+ };
+};
+
+&pinctrl {
+ leds {
+ blue_led_pin: blue-led-pin {
+ rockchip,pins = <0 RK_PD6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ green_led_pin: green-led-pin {
+ rockchip,pins = <0 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pmic {
+ pmic_int: pmic_int {
+ rockchip,pins =
+ <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+
+ };
+
+ usb {
+ vcc5v0_host_en: vcc5v0-host-en {
+ rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&pwm8 {
+ /* fan 5v - gnd - pwm */
+ status = "okay";
+};
+
+&pwm10 {
+ /* pin 7 of header con2 */
+ status = "disabled";
+};
+
+&pwm11 {
+ /* pin 15 of header con2 */
+ status = "disabled";
+};
+
+&pwm12 {
+ /* pin 21 of header con2 */
+ /* shared with uart9 + spi3 */
+ pinctrl-0 = <&pwm12m1_pins>;
+ status = "disabled";
+};
+
+&pwm13 {
+ /* pin 24 of header con2 */
+ /* shared with uart9 */
+ pinctrl-0 = <&pwm13m1_pins>;
+ status = "disabled";
+};
+
+&pwm14 {
+ /* pin 23 of header con2 */
+ /* shared with spi3 */
+ pinctrl-0 = <&pwm14m1_pins>;
+ status = "disabled";
+};
+
+&pwm15 {
+ /* pin 19 of header con2 */
+ /* shared with spi3 */
+ pinctrl-0 = <&pwm15m1_pins>;
+ status = "disabled";
+};
+
+&saradc {
+ vref-supply = <&vcca_1v8>;
+ status = "okay";
+};
+
+&sdhci {
+ bus-width = <8>;
+ max-frequency = <200000000>;
+ non-removable;
+ no-sd;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd &emmc_datastrobe>;
+ status = "okay";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ environment_emmc: partition at 408000 {
+ label = "barebox-environment";
+ reg = <0x0 0x408000 0x0 0x8000>;
+ };
+ };
+};
+
+&sdmmc0 {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ max-frequency = <150000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
+ sd-uhs-sdr104;
+ vmmc-supply = <&vcc3v3_sd>;
+ vqmmc-supply = <&vccio_sd>;
+ status = "okay";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ environment_sd: partition at 408000 {
+ label = "barebox-environment";
+ reg = <0x0 0x408000 0x0 0x8000>;
+ };
+ };
+};
+
+&spi3 {
+ /* pin 19 (MO) + 21 (MI) + 23 (CK) of header con2 */
+ /* shared with pwm12/14/15 and uart9 */
+ pinctrl-0 = <&spi3m1_pins>;
+ status = "disabled";
+};
+
+&tsadc {
+ status = "okay";
+};
+
+&uart0 {
+ /* pin 8 (TX) + 10 (RX) (RTS:16, CTS:18) of header con2 */
+ status = "disabled";
+};
+
+&uart2 {
+ /* debug-uart */
+ status = "okay";
+};
+
+&uart7 {
+ /* pin 11 (TX) + 13 (RX) of header con2 */
+ pinctrl-0 = <&uart7m1_xfer>;
+ status = "disabled";
+};
+
+&uart9 {
+ /* pin 21 (TX) + 24 (RX) of header con2 */
+ /* shared with pwm13 and pwm12/spi3 */
+ pinctrl-0 = <&uart9m1_xfer>;
+ status = "disabled";
+};
+
+&u2phy0_host {
+ phy-supply = <&vcc5v0_host>;
+ status = "okay";
+};
+
+&u2phy0_otg {
+ phy-supply = <&vcc5v0_host>;
+ status = "okay";
+};
+
+&u2phy1_host {
+ phy-supply = <&vcc5v0_host>;
+ status = "okay";
+};
+
+&u2phy1_otg {
+ phy-supply = <&vcc5v0_host>;
+ status = "okay";
+};
+
+&usb2phy0 {
+ status = "okay";
+};
+
+&usb2phy1 {
+ status = "okay";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host0_ohci {
+ status = "okay";
+};
+
+&usb_host1_ehci {
+ status = "okay";
+};
+
+&usb_host1_ohci {
+ status = "okay";
+};
+
+&usbdrd_dwc3 {
+ dr_mode = "host";
+ extcon = <&usb2phy0>;
+};
+
+&usbdrd30 {
+ status = "okay";
+};
+
+&usbhost30 {
+ status = "okay";
+};
+
+&combphy0_us {
+ status = "okay";
+};
+
+&combphy1_usq {
+ status = "okay";
+};
diff --git a/arch/arm/mach-rockchip/Kconfig b/arch/arm/mach-rockchip/Kconfig
index 3c6b3dd9b531..ffd3aa8a4e77 100644
--- a/arch/arm/mach-rockchip/Kconfig
+++ b/arch/arm/mach-rockchip/Kconfig
@@ -68,6 +68,12 @@ config MACH_RK3568_EVB
help
Say Y here if you are using a RK3568 EVB
+config MACH_RK3568_BPI_R2PRO
+ select ARCH_RK3568
+ bool "RK3568 BPI R2PRO"
+ help
+ Say Y here if you are using a RK3568 Bananpi R2 Pro
+
config MACH_PINE64_QUARTZ64
select ARCH_RK3568
bool "Pine64 Quartz64"
diff --git a/images/Makefile.rockchip b/images/Makefile.rockchip
index 0a485cad24d1..cdc7772c2e3d 100644
--- a/images/Makefile.rockchip
+++ b/images/Makefile.rockchip
@@ -14,6 +14,9 @@ image-$(CONFIG_MACH_PHYTEC_SOM_RK3288) += barebox-rk3288-phycore-som.img
pblb-$(CONFIG_MACH_RK3568_EVB) += start_rk3568_evb
image-$(CONFIG_MACH_RK3568_EVB) += barebox-rk3568-evb.img
+pblb-$(CONFIG_MACH_RK3568_BPI_R2PRO) += start_rk3568_bpi_r2pro
+image-$(CONFIG_MACH_RK3568_BPI_R2PRO) += barebox-rk3568-bpi-r2pro.img
+
pblb-$(CONFIG_MACH_PINE64_QUARTZ64) += start_quartz64a
image-$(CONFIG_MACH_PINE64_QUARTZ64) += barebox-quartz64a.img
@@ -24,6 +27,10 @@ $(obj)/barebox-rk3568-evb.img: $(obj)/start_rk3568_evb.pblb \
$(board)/rockchip-rk3568-evb/sdram-init.bin
$(call if_changed,rkimg_image)
+$(obj)/barebox-rk3568-bpi-r2pro.img: $(obj)/start_rk3568_bpi_r2pro.pblb \
+ $(board)/rockchip-rk3568-bpi-r2pro/sdram-init.bin
+ $(call if_changed,rkimg_image)
+
$(obj)/barebox-quartz64a.img: $(obj)/start_quartz64a.pblb \
$(board)/pine64-quartz64/sdram-init.bin
$(call if_changed,rkimg_image)
--
2.25.1
More information about the barebox
mailing list