[PATCH v1 1/1] usb: net: Add support for the Realtek RTL8152B/RTL8153

[Oleksij Rempel]

Hi Trent,

Thank you for the review.

On Tue, Oct 19, 2021 at 11:50:08AM -0700, Trent Piepho wrote:
> On Tue, Oct 19, 2021 at 3:24 AM Oleksij Rempel <o.rempel at pengutronix.de> wrote:
> > +
> > +       buf = malloc(size);
> > +       if (!buf)
> > +               return -ENOMEM;
> 
> Barebox could use xmalloc here.  Ditto for other malloc/return ENOMEM patterns.

done.

> > +static int r8152_write_hwaddr(struct eth_device *edev, const unsigned char *adr)
> > +{
> > +       struct r8152 *tp = edev->priv;
> > +       u8 tmp_addr[ETH_ALEN];
> > +
> > +       memcpy(tmp_addr, adr, ETH_ALEN);
> > +
> > +       debug("** %s (%d)\n", __func__, __LINE__);
> > +
> > +       ocp_write_byte(tp, MCU_TYPE_PLA, PLA_CRWECR, CRWECR_CONFIG);
> > +       pla_ocp_write(tp, PLA_IDR, BYTE_EN_SIX_BYTES, 8, tmp_addr);
> 
> This writes 8 bytes from a buffer of 6 bytes.

Ack, done.

> It doesn't seem like the temp buffer is even necessary.

it was const conversion. Now I converted complete write chain to const.

> > +/* Generic MII registers. */
> > +#define MII_BMCR                0x00    /* Basic mode control register */
> > +#define MII_BMSR                0x01    /* Basic mode status register  */
> > +#define MII_PHYSID1             0x02    /* PHYS ID 1                   */
> > +#define MII_PHYSID2             0x03    /* PHYS ID 2                   */
> > +#define MII_ADVERTISE           0x04    /* Advertisement control reg   */
> > +#define MII_LPA                 0x05    /* Link partner ability reg    */
> > +#define MII_EXPANSION           0x06    /* Expansion register          */
> > +#define MII_CTRL1000            0x09    /* 1000BASE-T control          */
> > +#define MII_STAT1000            0x0a    /* 1000BASE-T status           */
> > +#define MII_MMD_CTRL            0x0d    /* MMD Access Control Register */
> > +#define MII_MMD_DATA            0x0e    /* MMD Access Data Register */
> > +#define MII_ESTATUS             0x0f    /* Extended Status             */
> > +#define MII_DCOUNTER            0x12    /* Disconnect counter          */
> > +#define MII_FCSCOUNTER          0x13    /* False carrier counter       */
> > +#define MII_NWAYTEST            0x14    /* N-way auto-neg test reg     */
> > +#define MII_RERRCOUNTER         0x15    /* Receive error counter       */
> > +#define MII_SREVISION           0x16    /* Silicon revision            */
> > +#define MII_RESV1               0x17    /* Reserved...                 */
> > +#define MII_LBRERROR            0x18    /* Lpback, rx, bypass error    */
> > +#define MII_PHYADDR             0x19    /* PHY address                 */
> > +#define MII_RESV2               0x1a    /* Reserved...                 */
> > +#define MII_TPISTATUS           0x1b    /* TPI status for 10mbps       */
> > +#define MII_NCONFIG             0x1c    /* Network interface config    */
> 
> These are defined already in linux/mii.h

done

> > +
> > +static u8 r8152b_pla_patch_a[] = {
> 
> Surely all these firmware images can be const too.
> 

done

Regards,
Oleksij
-- 
Pengutronix e.K.                           |                             |
Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |