[PATCH v1 2/2] net: phy: micrel: port clock select support

[Oleksij Rempel]

Hi Trent,

thank you for your review.

On Tue, Oct 12, 2021 at 10:12:13AM -0700, Trent Piepho wrote:
> On Tue, Oct 12, 2021 at 3:10 AM Oleksij Rempel <o.rempel at pengutronix.de> wrote:
> >
> > Port devicetree based clock select support from kernel micrel driver (v5.15-rc1).
> > This support is needed to make netboot work on boards with PHY node and
> > "rmii-ref" property.
> 
> Existing boards use a phy fixup to handle this case, e.g. fsl,imx6ull-14x14-evk:
> 
> static int nxp_imx6ull_evk_init(void)
> {
>          phy_register_fixup_for_uid(PHY_ID_KSZ8081, MICREL_PHY_ID_MASK,
>                        ksz8081_phy_fixup);
> 
> static int ksz8081_phy_fixup(struct phy_device *dev)
> {
>        phy_write(dev, 0x1f, 0x8190);
>        phy_write(dev, 0x16, 0x202);
> 
> I thought about extending micrel driver like this when I added support
> for NXP imx6ul (single L, not double L as above) dev kit but decided
> it was a lot of code for what ends up being one register write for
> boards using a ksz8081 and the barebox phy fixup concept, which
> handles this in only a couple lines, was easier.

No, I would hardly not recommend to do it this way :)

> Also look at ks8051_config_init(), it checks phydev->dev_flags to set
> this same bit.  But AFAICT, dev_flags is not used in Barebox.

Good point. I'll remove it.
> 
> > +/* PHY Control 2 / PHY Control (if no PHY Control 1) */
> > +#define MII_KSZPHY_CTRL_2                      0x1f
> > +#define KSZPHY_RMII_REF_CLK_SEL                        BIT(7)
> 
> These are already in this file as MII_KSZPHY_CTRL and KSZ8051_RMII_50MHZ_CLK.
> 
> > +struct kszphy_type {
> > +       bool has_rmii_ref_clk_sel;
> > +};
> > +
> > +struct kszphy_priv {
> > +       const struct kszphy_type *type;
> 
> type does not appear to be used from the state struct.
> 
> > +       bool rmii_ref_clk_sel;
> > +       bool rmii_ref_clk_sel_val;
> 
> All you need is a single flag to indicate the KSZ8051_RMII_50MHZ_CLK
> bit should be set after a reset.  Otherwise it can be left unset,
> which is the default value.
> 
> > +static const struct kszphy_type ksz8081_type = {
> > +       .has_rmii_ref_clk_sel   = true,
> > +};
> 
> Note that not just KSZ8081 has this bit.  Also KSZ8021, KSZ8031, and
> KSZ8051, which has the existing different method to handle it, as
> described earlier.

ok, i'll sync all of this PHYs with the state of the kernel driver.
The board fixups should be removed by someone who can confirm it.

> > +static int kszphy_rmii_clk_sel(struct phy_device *phydev, bool val)
> > +{
> > +       int ctrl;
> > +
> > +       ctrl = phy_read(phydev, MII_KSZPHY_CTRL);
> > +       if (ctrl < 0)
> > +               return ctrl;
> > +
> > +       if (val)
> > +               ctrl |= KSZPHY_RMII_REF_CLK_SEL;
> > +       else
> > +               ctrl &= ~KSZPHY_RMII_REF_CLK_SEL;
> > +
> > +       return phy_write(phydev, MII_KSZPHY_CTRL, ctrl);
> > +}
> 
> phy_set_bits(phydev, MII_KSZPHY_CTRL, KSZ8051_RMII_50MHZ_CLK);

No, it should be synced with kernel not in the opposite way.

> > +
> > +       /* Support legacy board-file configuration */
> > +       if (phydev->dev_flags & MICREL_PHY_50MHZ_CLK) {
> > +               priv->rmii_ref_clk_sel = true;
> > +               priv->rmii_ref_clk_sel_val = true;
> > +       }
> 
> Can't code in ksz8051_config_init be removed then?

good point, i'll remove it.

Regards,
Oleksij
-- 
Pengutronix e.K.                           |                             |
Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |