[PATCH v1] ARM: dts: protonic: drop all devictree copies and start to use mainlined kernel versions
Oleksij Rempel
o.rempel at pengutronix.de
Wed Mar 17 12:08:09 GMT 2021
This should make maintaining work easier.
Signed-off-by: Oleksij Rempel <o.rempel at pengutronix.de>
---
arch/arm/dts/imx6dl-alti6p.dts | 119 +----
arch/arm/dts/imx6dl-lanmcu.dts | 463 +-----------------
arch/arm/dts/imx6dl-plybas.dts | 185 +------
arch/arm/dts/imx6dl-plym2m.dts | 176 +------
arch/arm/dts/imx6dl-prtmvt.dts | 163 +------
arch/arm/dts/imx6dl-prtrvt.dts | 184 +------
arch/arm/dts/imx6dl-prtvt7.dts | 473 +-----------------
arch/arm/dts/imx6dl-victgo.dts | 144 +-----
arch/arm/dts/imx6dl-vicut1.dts | 50 +-
arch/arm/dts/imx6q-prti6q.dts | 533 +-------------------
arch/arm/dts/imx6q-prtwd2.dts | 187 +------
arch/arm/dts/imx6q-vicut1.dts | 65 +--
arch/arm/dts/imx6qdl-prti6q-emmc.dtsi | 49 ++
arch/arm/dts/imx6qdl-prti6q-nor.dtsi | 5 +
arch/arm/dts/imx6qdl-prti6q.dtsi | 216 ---------
arch/arm/dts/imx6qdl-vicut1.dtsi | 234 ---------
arch/arm/dts/imx6qp-prtwd3.dts | 675 +-------------------------
arch/arm/dts/imx6qp-vicutp.dts | 51 +-
arch/arm/dts/imx6ul-prti6g.dts | 109 ++---
arch/arm/dts/imx6ul-prti6g.dtsi | 330 -------------
20 files changed, 133 insertions(+), 4278 deletions(-)
create mode 100644 arch/arm/dts/imx6qdl-prti6q-emmc.dtsi
delete mode 100644 arch/arm/dts/imx6qdl-prti6q.dtsi
delete mode 100644 arch/arm/dts/imx6qdl-vicut1.dtsi
delete mode 100644 arch/arm/dts/imx6ul-prti6g.dtsi
diff --git a/arch/arm/dts/imx6dl-alti6p.dts b/arch/arm/dts/imx6dl-alti6p.dts
index 8d53100bea..04a6368f93 100644
--- a/arch/arm/dts/imx6dl-alti6p.dts
+++ b/arch/arm/dts/imx6dl-alti6p.dts
@@ -1,118 +1,5 @@
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-/*
- * Copyright (c) 2016 Protonic Holland
- */
-
+// SPDX-License-Identifier: GPL-2.0-or-later
/dts-v1/;
-#include <arm/imx6dl.dtsi>
-#include "imx6qdl-prti6q.dtsi"
-
-/ {
- model = "Altesco I6P Board";
- compatible = "alt,alti6p", "fsl,imx6dl";
-
- memory at 10000000 {
- device_type = "memory";
- reg = <0x10000000 0x40000000>;
- };
-};
-
-&hdmi {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_hdmi>;
- ddc-i2c-bus = <&i2c1>;
- status = "okay";
-};
-
-/* DDC */
-&i2c1 {
- clock-frequency = <100000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c1>;
- status = "okay";
-};
-
-&i2c3 {
- rtc: pcf8563 at 51 {
- compatible = "nxp,pcf8563";
- reg = <0x51>;
- };
-};
-
-&fec {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_enet>;
- phy-mode = "rmii";
- phy-reset-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
- clocks = <&clks IMX6QDL_CLK_ENET>,
- <&clks IMX6QDL_CLK_ENET>;
- clock-names = "ipg", "ahb";
- status = "okay";
-};
-
-&i2c2 {
- clock-frequency = <50000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c2>;
- status = "okay";
-};
-
-&i2c4 {
- clock-frequency = <50000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c4>;
- status = "okay";
-};
-
-&iomuxc {
- pinctrl_usbotg: usbotggrp {
- fsl,pins = <
- MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x1f058
- MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
- /* power enable, high active */
- MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
- >;
- };
-
- pinctrl_hdmi: hdmigrp {
- fsl,pins = <
- /* NOTE: DDC is done via I2C2, so DON'T configure DDC pins for HDMI! */
- MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE 0x1f8b0
- >;
- };
-
- pinctrl_i2c2: i2c2grp {
- fsl,pins = <
- MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
- MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
- >;
- };
-
- pinctrl_i2c4: i2c4grp {
- fsl,pins = <
- MX6QDL_PAD_NANDF_CS3__I2C4_SDA 0x4001f8b1
- MX6QDL_PAD_NANDF_WP_B__I2C4_SCL 0x4001f8b1
- >;
- };
-
- pinctrl_enet: enetgrp {
- fsl,pins = <
- /* MX6QDL_ENET_PINGRP4 */
- MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
- MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
- MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
- MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
- MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0
- MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
- MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
- MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
- MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
- MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0
- /* Phy reset */
- MX6QDL_PAD_CSI0_DAT4__GPIO5_IO22 0x1b0b0
- /* nINTRP */
- MX6QDL_PAD_CSI0_DAT5__GPIO5_IO23 0x1b0b0
- >;
- };
-};
+#include <arm/imx6dl-alti6p.dts>
+#include "imx6qdl-prti6q-nor.dtsi"
diff --git a/arch/arm/dts/imx6dl-lanmcu.dts b/arch/arm/dts/imx6dl-lanmcu.dts
index d50e6afe7e..1a1fbad326 100644
--- a/arch/arm/dts/imx6dl-lanmcu.dts
+++ b/arch/arm/dts/imx6dl-lanmcu.dts
@@ -1,464 +1,5 @@
// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (c) 2019 Protonic Holland
- */
-
/dts-v1/;
-#include <arm/imx6dl.dtsi>
-#include <dt-bindings/gpio/gpio.h>
-
-/ {
- model = "LANMCU";
- compatible = "lan,lanmcu", "fsl,imx6dl";
-
- chosen {
- stdout-path = &uart4;
-
- environment-emmc {
- compatible = "barebox,environment";
- device-path = &usdhc3, "partname:barebox-environment";
- };
- };
-
- memory {
- reg = <0x10000000 0x10000000>;
- };
-
- reg_usb_otg_vbus: otg-vbus-regulator {
- compatible = "regulator-fixed";
- regulator-name = "regulator-OTG-VBUS";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- gpio = <&gpio3 22 0>;
- enable-active-high;
- };
-
- usdhc2_pwrseq: usdhc2_pwrseq {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_wlan_npd>;
- compatible = "mmc-pwrseq-simple";
- reset-gpios = <&gpio6 10 GPIO_ACTIVE_LOW>;
- };
-
- display: display0 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ipu1_disp>;
- compatible = "fsl,imx-parallel-display";
- #address-cells = <1>;
- #size-cells = <0>;
- interface-pix-fmt = "bgr666";
- status = "okay";
-
- port at 0 {
- reg = <0>;
-
- display_in: endpoint {
- remote-endpoint = <&ipu1_di0_disp0>;
- };
- };
-
- port at 1 {
- reg = <1>;
-
- display_out: endpoint {
- remote-endpoint = <&panel_in>;
- };
- };
- };
-
- panel {
- compatible = "edt,etm0700g0bdh6";
- backlight = <&backlight_lcd>;
-
- port {
- panel_in: endpoint {
- remote-endpoint = <&display_out>;
- };
- };
- };
-
- backlight_lcd: backlight_lcd {
- compatible = "pwm-backlight";
- pwms = <&pwm1 0 5000000 0>;
- brightness-levels = <0 5 7 9 12 15 20 27 35 47 62 81 107 142 188 248
- 328 433 573 757 1000>;
- default-brightness-level = <20>;
- status = "okay";
- };
-
- leds: leds {
- compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_leds>;
-
- debug0 {
- label = "debug0";
- gpios = <&gpio1 8 0>;
- linux,default-trigger = "heartbeat";
- };
- };
-
- clk50m_phy: phy_clock {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <50000000>;
- };
-};
-
-&iomuxc {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_hog>;
-
- prti6q {
- pinctrl_hog: hoggrp {
- fsl,pins = <
- /* HW revision detect */
- MX6QDL_PAD_SD4_DAT0__GPIO2_IO08 0x1b0b0 /* REV_ID0 */
- MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x1b0b0 /* REV_ID1 */
- MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0 /* REV_ID2 */
- MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x1b0b0 /* REV_ID3 */
- MX6QDL_PAD_SD4_DAT4__GPIO2_IO12 0x1b0b0 /* REV_ID4 */
- >;
- };
-
- pinctrl_usbotg: usbotggrp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
- /* power enable, high active */
- MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
- >;
- };
-
- pinctrl_ipu1_disp: ipudisp1grp {
- fsl,pins = <
- /* DSE 0x30 => 25 Ohm, 0x20 => 37 Ohm, 0x10 => 75 Ohm */
- MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x30
- MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x30
- MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x30
- MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x30
- MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x30
- MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x30
- MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x30
- MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x30
- MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x30
- MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x30
- MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x30
- MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x30
- MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x30
- MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x30
- MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x30
- MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x30
- MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x30
- MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x30
- MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x30
- MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x30
- MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x30
- MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x30
- >;
- };
-
- pinctrl_enet: enetgrp {
- fsl,pins = <
- /* MX6QDL_ENET_PINGRP4 */
- MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
- MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
- MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
- MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
- MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0
- MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
- MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
- MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
- MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
-
- MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0
- /* Phy reset */
- MX6QDL_PAD_CSI0_DAT4__GPIO5_IO22 0x1b0b0
- /* nINTRP */
- MX6QDL_PAD_CSI0_DAT5__GPIO5_IO23 0x1b0b0
- >;
- };
-
- pinctrl_pwm1: pwm1grp {
- fsl,pins = <
- MX6QDL_PAD_GPIO_9__PWM1_OUT 0x1b0b0
- >;
- };
-
- pinctrl_leds: ledsgrp {
- fsl,pins = <
- MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
- >;
- };
-
- pinctrl_wlan_npd: wlan_npd {
- fsl,pins = <
- /* WL_REG_ON */
- MX6QDL_PAD_NANDF_RB0__GPIO6_IO10 0x13069
- >;
- };
-
- pinctrl_uart2: uart2grp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D26__UART2_RX_DATA 0x1b0b1
- MX6QDL_PAD_EIM_D27__UART2_TX_DATA 0x1b0b1
- MX6QDL_PAD_EIM_D28__UART2_CTS_B 0x130b1
- >;
- };
-
- pinctrl_uart3: uart3grp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
- MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
- MX6QDL_PAD_EIM_D30__UART3_CTS_B 0x130b1
- >;
- };
-
- pinctrl_uart4: uart4grp {
- fsl,pins = <
- MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
- MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
- >;
- };
-
- pinctrl_i2c1: i2c1grp {
- fsl,pins = <
- MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1
- MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1
- >;
- };
-
- pinctrl_i2c3: i2c3grp {
- fsl,pins = <
- MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
- MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
- >;
- };
-
- pinctrl_usdhc1: usdhc1grp {
- fsl,pins = <
- MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9
- MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9
- MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9
- MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9
- MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9
- MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9
- MX6QDL_PAD_GPIO_1__SD1_CD_B 0x1b0b0
- >;
- };
-
- pinctrl_usdhc2: usdhc2grp {
- fsl,pins = <
- MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9
- MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9
- MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
- MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
- MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
- MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9
- >;
- };
-
- pinctrl_usdhc3: usdhc3grp {
- fsl,pins = <
- MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
- MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099
- MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099
- MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099
- MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099
- MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099
- MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099
- MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099
- MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099
- MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
- >;
- };
-
- pinctrl_can1: can1grp {
- fsl,pins = <
- MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x80000000
- MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x80000000
- >;
- };
-
- pinctrl_can2: can2grp {
- fsl,pins = <
- MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x80000000
- MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x80000000
- >;
- };
-
- pinctrl_ts_edt: ts1grp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b0
- >;
- };
- };
-};
-
-&ipu1_di0_disp0 {
- remote-endpoint = <&display_in>;
-};
-
-&pwm1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_pwm1>;
- status = "okay";
-};
-
-&fec {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_enet>;
- phy-mode = "rmii";
- clocks = <&clks IMX6QDL_CLK_ENET>,
- <&clks IMX6QDL_CLK_ENET>,
- <&clk50m_phy>;
- clock-names = "ipg", "ahb", "ptp";
- status = "okay";
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- /* Microchip KSZ8081RNA PHY */
- rgmii_phy: ethernet-phy at 0 {
- reg = <0>;
- interrupts-extended = <&gpio5 23 IRQ_TYPE_LEVEL_LOW>;
- reset-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
- reset-assert-us = <10000>;
- reset-deassert-us = <300>;
- };
- };
-};
-
-&uart2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart2>;
- linux,rs485-enabled-at-boot-time;
- uart-has-rtscts;
- status = "okay";
-};
-
-&uart3 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart3>;
- linux,rs485-enabled-at-boot-time;
- uart-has-rtscts;
- status = "okay";
-};
-
-&uart4 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart4>;
- status = "okay";
-};
-
-&usbotg {
- vbus-supply = <®_usb_otg_vbus>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usbotg>;
- phy_type = "utmi";
- dr_mode = "host";
- status = "okay";
-};
-
-&i2c1 {
- clock-frequency = <100000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c1>;
- status = "okay";
-};
-
-&i2c3 {
- clock-frequency = <100000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c3>;
- status = "okay";
-
- rtc: pcf8563 at 51 {
- compatible = "nxp,pcf8563";
- reg = <0x51>;
- };
-
- touchscreen: edt_ft5406 at 38 {
- compatible = "edt,edt-ft5406";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ts_edt>;
- reg = <0x38>;
- interrupt-parent = <&gpio3>;
- interrupts = <20 IRQ_TYPE_EDGE_FALLING>;
-
- touchscreen-size-x = <1792>;
- touchscreen-size-y = <1024>;
-
- touchscreen-fuzz-x = <0>;
- touchscreen-fuzz-y = <0>;
-
- /* Touch screen calibration */
- threshold = <50>;
- gain = <5>;
- offset = <10>;
- };
-};
-
-&usdhc1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc1>;
- cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
- status = "okay";
-};
-
-&usdhc2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc2>;
- no-1-8-v;
- non-removable;
- mmc-pwrseq = <&usdhc2_pwrseq>;
- pm-ignore-notify;
- status = "okay";
- #address-cells = <1>;
- #size-cells = <0>;
-
- brcmf: bcrmf at 1 {
- reg = <1>;
- compatible = "brcm,bcm4329-fmac";
- };
-};
-
-&usdhc3 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc3>;
- bus-width = <8>;
- non-removable;
- status = "okay";
-
- partitions {
- /*
- * Map a partition at the last 64k of the area available for
- * the second stage bootloader.
- */
- compatible = "fixed-partitions";
- #size-cells = <1>;
- #address-cells = <1>;
-
- partition at 100000 {
- label = "barebox-environment";
- reg = <0x100000 0x100000>;
- };
-
- partition at 200000 {
- label = "state";
- reg = <0x200000 0x100000>;
- };
- };
-};
-
-&can1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_can1>;
- status = "okay";
-};
-&can2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_can2>;
- status = "okay";
-};
+#include <arm/imx6dl-lanmcu.dts>
+#include "imx6qdl-prti6q-emmc.dtsi"
diff --git a/arch/arm/dts/imx6dl-plybas.dts b/arch/arm/dts/imx6dl-plybas.dts
index de0ba05e13..b0e1595a41 100644
--- a/arch/arm/dts/imx6dl-plybas.dts
+++ b/arch/arm/dts/imx6dl-plybas.dts
@@ -1,186 +1,5 @@
// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (c) 2014 Protonic Holland
- */
-
/dts-v1/;
-#include <arm/imx6dl.dtsi>
-#include "imx6qdl-vicut1.dtsi"
-
-/ {
- model = "Plymovent BAS board";
- compatible = "ply,plybas", "fsl,imx6dl";
-
- memory {
- reg = <0x10000000 0x10000000>;
- };
-
- backlight_lcd {
- status = "disabled";
- };
-
- gpio_keys {
- compatible = "gpio-keys";
- #address-cells = <1>;
- #size-cells = <0>;
- autorepeat;
- button at 20 {
- label = "START";
- linux,code = <31>;
- gpios = <&gpio5 8 1>;
- };
- button at 21 {
- label = "CLEAN";
- linux,code = <46>;
- gpios = <&gpio5 9 1>;
- };
- };
-
- leds: leds {
- compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_leds>;
-
- debug0 {
- label = "debug0";
- gpios = <&gpio1 8 0>;
- };
-
- debug1 {
- label = "debug1";
- gpios = <&gpio1 9 0>;
- };
-
- light_tower1 {
- label = "light_tower1";
- gpios = <&gpio4 22 0>;
- linux,default-trigger = "heartbeat";
- };
-
- light_tower2 {
- label = "light_tower2";
- gpios = <&gpio4 23 0>;
- };
-
- light_tower3 {
- label = "light_tower3";
- gpios = <&gpio4 24 0>;
- };
-
- light_tower4 {
- label = "light_tower4";
- gpios = <&gpio4 25 0>;
- };
- };
-};
-
-&fec {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_enet>;
- phy-mode = "rmii";
- phy-reset-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
- clocks = <&clks IMX6QDL_CLK_ENET>,
- <&clks IMX6QDL_CLK_ENET>;
- clock-names = "ipg", "ahb";
- status = "okay";
-};
-
-&uart2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart2>;
- fsl,uart-has-rtscts;
- linux,rs485-enabled-at-boot-time;
- rs485-rts-delay = <0 20>;
- status = "okay";
-};
-
-&iomuxc {
- pinctrl_hog: hoggrp {
- fsl,pins = <
- /* CAN1_SR + CAN2_SR GPIO outputs */
- MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13070
- MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x13070
-
- MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x1b0b0 /* YACO_nIRQ */
- MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x130b0 /* YACO_BOOT0 */
- MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x1b0b0 /* YACO_nRESET */
-
- MX6QDL_PAD_DISP0_DAT0__GPIO4_IO21 0x13070 /* BUZZER */
- MX6QDL_PAD_DISP0_DAT6__GPIO4_IO27 0x13070 /* ANA_OUT_SD */
- MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28 0x1b0b0 /* ANA_OUT_ERR */
-
- MX6QDL_PAD_DISP0_DAT11__GPIO5_IO05 0x13070 /* RELAY1 */
- MX6QDL_PAD_DISP0_DAT12__GPIO5_IO06 0x13070 /* RELAY2 */
-
- MX6QDL_PAD_DISP0_DAT14__GPIO5_IO08 0x1b0b0 /* IN1 */
- MX6QDL_PAD_DISP0_DAT15__GPIO5_IO09 0x1b0b0 /* IN2 */
- MX6QDL_PAD_DISP0_DAT16__GPIO5_IO10 0x1b0b0 /* IN3 */
- MX6QDL_PAD_DISP0_DAT17__GPIO5_IO11 0x1b0b0 /* IN4 */
- MX6QDL_PAD_DISP0_DAT18__GPIO5_IO12 0x1b0b0 /* IN5 */
- MX6QDL_PAD_DISP0_DAT19__GPIO5_IO13 0x1b0b0 /* IN6 */
- MX6QDL_PAD_DISP0_DAT20__GPIO5_IO14 0x1b0b0 /* IN7 */
- MX6QDL_PAD_DISP0_DAT21__GPIO5_IO15 0x1b0b0 /* IN8 */
- MX6QDL_PAD_DISP0_DAT22__GPIO5_IO16 0x1b0b0 /* IN9 */
- MX6QDL_PAD_DISP0_DAT23__GPIO5_IO17 0x1b0b0 /* IN10 */
- MX6QDL_PAD_DI0_PIN4__GPIO4_IO20 0x1b0b0 /* IN11 */
- MX6QDL_PAD_DI0_PIN2__GPIO4_IO18 0x1b0b0 /* IN12 */
-
- MX6QDL_PAD_DI0_PIN3__GPIO4_IO19 0x1a0b0 /* HMI */
-
- /* HW revision detect */
- MX6QDL_PAD_SD4_DAT0__GPIO2_IO08 0x1b0b0 /* REV_ID0 */
- MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x1b0b0 /* REV_ID1 */
- MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0 /* REV_ID2 */
- MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x1b0b0 /* REV_ID3 */
- MX6QDL_PAD_SD4_DAT4__GPIO2_IO12 0x1b0b0 /* REV_ID4 */
- >;
- };
-
- pinctrl_leds: ledsgrp {
- fsl,pins = <
- MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0 /* DEBUG0 */
- MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0 /* DEBUG1 */
-
- MX6QDL_PAD_DISP0_DAT1__GPIO4_IO22 0x13070 /* LED1 (lighttower) */
- MX6QDL_PAD_DISP0_DAT2__GPIO4_IO23 0x13070 /* LED2 (lighttower) */
- MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x13070 /* LED3 (lighttower) */
- MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25 0x13070 /* LED4 (lighttower) */
- >;
- };
-
- /* RS485 UART */
- pinctrl_uart2: uart2grp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1
- MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1
- MX6QDL_PAD_EIM_D28__UART2_DTE_CTS_B 0x130b1
- >;
- };
-
- pinctrl_pwm1: pwm1grp {
- fsl,pins = <
- MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0
- >;
- };
-
- pinctrl_enet: enetgrp {
- fsl,pins = <
- /* MX6QDL_ENET_PINGRP4 */
- MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
- MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
- MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
- MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
- MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0
- MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
- MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
- MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
- MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
- MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0
- /* Phy reset */
- MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26 0x1b0b0
- /* nINTRP */
- MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30 0x1b0b0
- >;
- };
-};
+#include <arm/imx6dl-plybas.dts>
+#include "imx6qdl-prti6q-nor.dtsi"
diff --git a/arch/arm/dts/imx6dl-plym2m.dts b/arch/arm/dts/imx6dl-plym2m.dts
index e944a14dce..bf29fc1bce 100644
--- a/arch/arm/dts/imx6dl-plym2m.dts
+++ b/arch/arm/dts/imx6dl-plym2m.dts
@@ -1,177 +1,5 @@
// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (c) 2014 Protonic Holland
- */
-
/dts-v1/;
-#include <arm/imx6dl.dtsi>
-#include "imx6qdl-prti6q.dtsi"
-#include "imx6qdl-prti6q-nor.dtsi"
-
-/ {
- model = "Plymovent M2M board";
- compatible = "ply,plym2m", "fsl,imx6dl";
-
- memory {
- reg = <0x10000000 0x10000000>;
- };
-
- leds: leds {
- compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_leds>;
-
- debug0 {
- label = "debug0";
- gpios = <&gpio1 8 0>;
- linux,default-trigger = "heartbeat";
- };
- };
-
- clk50m_phy: phy_clock {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <50000000>;
- };
-};
-
-&ecspi1 {
- cs-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ecspi1>;
- status = "okay";
-
- flash at 0 {
- compatible = "jedec,spi-nor";
- reg = <0>;
- spi-max-frequency = <20000000>;
- #address-cells = <1>;
- #size-cells = <1>;
- };
-};
-
-&fec {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_enet>;
- phy-mode = "rmii";
- clocks = <&clks IMX6QDL_CLK_ENET>,
- <&clks IMX6QDL_CLK_ENET>,
- <&clk50m_phy>;
- clock-names = "ipg", "ahb", "ptp";
- status = "okay";
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- /* Microchip KSZ8081RNA PHY */
- rgmii_phy: ethernet-phy at 0 {
- reg = <0>;
- interrupts-extended = <&gpio5 23 IRQ_TYPE_LEVEL_LOW>;
- reset-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
- reset-assert-us = <10000>;
- reset-deassert-us = <300>;
- };
- };
-};
-&iomuxc {
- pinctrl_hog: hoggrp {
- fsl,pins = <
- /* CAN1_SR GPIO output */
- MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13070
-
- MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0 /* CAN1_TERM */
- MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0 /* TSC_BUSY */
-
- /* HW revision detect */
- MX6QDL_PAD_SD4_DAT0__GPIO2_IO08 0x1b0b0 /* REV_ID0 */
- MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x1b0b0 /* REV_ID1 */
- MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0 /* REV_ID2 */
- MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x1b0b0 /* REV_ID3 */
- MX6QDL_PAD_SD4_DAT4__GPIO2_IO12 0x1b0b0 /* REV_ID4 */
- >;
- };
-
- pinctrl_ecspi1: ecspi1grp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
- MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
- MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
- /* CS */
- MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1
- >;
- };
-
- pinctrl_usbotg: usbotggrp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
- /* power enable, high active */
- MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
- >;
- };
-
- pinctrl_ipu1_disp: ipudisp1grp {
- fsl,pins = <
- /* DSE 0x30 => 25 Ohm, 0x20 => 37 Ohm, 0x10 => 75 Ohm */
- MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x30
- MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x30
- MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x30
- MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x30
- MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x30
- MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x30
- MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x30
- MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x30
- MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x30
- MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x30
- MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x30
- MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x30
- MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x30
- MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x30
- MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x30
- MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x30
- MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x30
- MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x30
- MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x30
- MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x30
- MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x30
- MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x30
- >;
- };
-
- pinctrl_enet: enetgrp {
- fsl,pins = <
- /* MX6QDL_ENET_PINGRP4 */
- MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
- MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
- MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
- MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
- MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0
- MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
- MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
- MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
- MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
-
- MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0
- /* Phy reset */
- MX6QDL_PAD_CSI0_DAT4__GPIO5_IO22 0x1b0b0
- /* nINTRP */
- MX6QDL_PAD_CSI0_DAT5__GPIO5_IO23 0x1b0b0
- >;
- };
-
- pinctrl_pwm1: pwm1grp {
- fsl,pins = <
- MX6QDL_PAD_GPIO_9__PWM1_OUT 0x1b0b0
- >;
- };
-
- pinctrl_backlight_m2m: backlightm2mgrp {
- };
-
- pinctrl_leds: ledsgrp {
- fsl,pins = <
- MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
- >;
- };
-};
+#include <arm/imx6dl-plym2m.dts>
+#include "imx6qdl-prti6q-nor.dtsi"
diff --git a/arch/arm/dts/imx6dl-prtmvt.dts b/arch/arm/dts/imx6dl-prtmvt.dts
index 05fce7178f..64e2f90110 100644
--- a/arch/arm/dts/imx6dl-prtmvt.dts
+++ b/arch/arm/dts/imx6dl-prtmvt.dts
@@ -1,164 +1,5 @@
// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (c) 2014 Protonic Holland
- */
-
/dts-v1/;
-#include <arm/imx6dl.dtsi>
-#include "imx6qdl-vicut1.dtsi"
-
-/ {
- model = "Protonic MVT board";
- compatible = "prt,prtmvt", "fsl,imx6dl";
-
- memory {
- reg = <0x10000000 0x20000000>;
- };
-
- gpio_keys {
- compatible = "gpio-keys";
- #address-cells = <1>;
- #size-cells = <0>;
- autorepeat;
-
- button at 20 {
- label = "GPIO Key F1";
- linux,code = <59>;
- gpios = <&pca_gpio 0 GPIO_ACTIVE_LOW>;
- };
- button at 21 {
- label = "GPIO Key F2";
- linux,code = <60>;
- gpios = <&pca_gpio 1 GPIO_ACTIVE_LOW>;
- };
- button at 22 {
- label = "GPIO Key F3";
- linux,code = <61>;
- gpios = <&pca_gpio 2 GPIO_ACTIVE_LOW>;
- };
- button at 23 {
- label = "GPIO Key F4";
- linux,code = <62>;
- gpios = <&pca_gpio 3 GPIO_ACTIVE_LOW>;
- };
- button at 24 {
- label = "GPIO Key F5";
- linux,code = <63>;
- gpios = <&pca_gpio 4 GPIO_ACTIVE_LOW>;
- };
-
- // Center
- button at 25 {
- label = "GPIO Key CYCLE";
- linux,code = <154>;
- gpios = <&pca_gpio 5 GPIO_ACTIVE_LOW>;
- };
- button at 26 {
- label = "GPIO Key ESC";
- linux,code = <1>;
- gpios = <&pca_gpio 6 GPIO_ACTIVE_LOW>;
- };
- button at 27 {
- label = "GPIO Key UP";
- linux,code = <103>;
- gpios = <&pca_gpio 7 GPIO_ACTIVE_LOW>;
- };
- button at 28 {
- label = "GPIO Key DOWN";
- linux,code = <108>;
- gpios = <&pca_gpio 8 GPIO_ACTIVE_LOW>;
- };
- button at 29 {
- label = "GPIO Key OK";
- linux,code = <0x160>;
- gpios = <&pca_gpio 9 GPIO_ACTIVE_LOW>;
- };
-
- button at 2a {
- label = "GPIO Key F6";
- linux,code = <64>;
- gpios = <&pca_gpio 10 GPIO_ACTIVE_LOW>;
- };
- button at 2b {
- label = "GPIO Key F7";
- linux,code = <65>;
- gpios = <&pca_gpio 11 GPIO_ACTIVE_LOW>;
- };
- button at 2c {
- label = "GPIO Key F8";
- linux,code = <66>;
- gpios = <&pca_gpio 12 GPIO_ACTIVE_LOW>;
- };
- button at 2d {
- label = "GPIO Key F9";
- linux,code = <67>;
- gpios = <&pca_gpio 13 GPIO_ACTIVE_LOW>;
- };
- button at 2e {
- label = "GPIO Key F10";
- linux,code = <68>;
- gpios = <&pca_gpio 14 GPIO_ACTIVE_LOW>;
- };
- };
-};
-
-&fec {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_enet>;
- phy-mode = "rmii";
- phy-reset-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
- clocks = <&clks IMX6QDL_CLK_ENET>,
- <&clks IMX6QDL_CLK_ENET>;
- clock-names = "ipg", "ahb";
- status = "okay";
-};
-
-&pwm2 {
- status = "disabled";
-};
-
-&pcie {
- status = "disabled";
-};
-
-&i2c1 {
- pca_gpio: gpio at 74 {
- #gpio-cells = <2>;
- compatible = "nxp,pca9539";
- reg = <0x74>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_pca9539>;
- interrupt-parent = <&gpio4>;
- interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
- gpio-controller;
- };
-};
-
-&iomuxc {
- pinctrl_enet: enetgrp {
- fsl,pins = <
- /* MX6QDL_ENET_PINGRP4 */
- MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
- MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
- MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
- MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
- MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0
- MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
- MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
- MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
- MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
-
- MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0
- /* Phy reset */
- MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26 0x1b0b0
- /* nINTRP */
- MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30 0x1b0b0
- >;
- };
- pinctrl_pca9539: pca9539 {
- fsl,pins = <
- MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x1b0b0
- >;
- };
-};
+#include <arm/imx6dl-prtmvt.dts>
+#include "imx6qdl-prti6q-nor.dtsi"
diff --git a/arch/arm/dts/imx6dl-prtrvt.dts b/arch/arm/dts/imx6dl-prtrvt.dts
index c403ba3ea7..e0d9261d27 100644
--- a/arch/arm/dts/imx6dl-prtrvt.dts
+++ b/arch/arm/dts/imx6dl-prtrvt.dts
@@ -1,183 +1,5 @@
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-/*
- * Copyright (c) 2014 Protonic Holland
- */
-
+// SPDX-License-Identifier: GPL-2.0-or-later
/dts-v1/;
-#include <arm/imx6dl.dtsi>
-#include "imx6qdl-prti6q.dtsi"
-#include "imx6qdl-prti6q-nor.dtsi"
-#include <dt-bindings/leds/common.h>
-
-/ {
- model = "Protonic RVT board";
- compatible = "prt,prtrvt", "fsl,imx6dl";
-
- memory at 10000000 {
- device_type = "memory";
- reg = <0x10000000 0x10000000>;
- };
-
- leds {
- compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_leds>;
-
- led-debug0 {
- function = LED_FUNCTION_STATUS;
- gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "heartbeat";
- };
- };
-};
-
-&can1 {
- pinctrl-0 = <&pinctrl_can1 &pinctrl_can1phy>;
-};
-
-&ecspi1 {
- cs-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ecspi1>;
- status = "okay";
-
- flash at 0 {
- compatible = "jedec,spi-nor";
- reg = <0>;
- spi-max-frequency = <20000000>;
- #address-cells = <1>;
- #size-cells = <1>;
- };
-};
-
-&ecspi3 {
- cs-gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ecspi3>;
- status = "okay";
-
- nfc at 0 {
- compatible = "ti,trf7970a";
- reg = <0>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_nfc>;
- spi-max-frequency = <2000000>;
- interrupts-extended = <&gpio5 14 IRQ_TYPE_LEVEL_LOW>;
- ti,enable-gpios = <&gpio5 12 GPIO_ACTIVE_LOW>,
- <&gpio5 11 GPIO_ACTIVE_LOW>;
- vin-supply = <®_3v3>;
- vin-voltage-override = <3100000>;
- autosuspend-delay = <30000>;
- irq-status-read-quirk;
- en2-rf-quirk;
- t5t-rmb-extra-byte-quirk;
- status = "okay";
- };
-};
-
-&i2c3 {
- adc at 49 {
- compatible = "ti,ads1015";
- reg = <0x49>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- /* nc */
- channel at 4 {
- reg = <4>;
- ti,gain = <3>;
- ti,datarate = <3>;
- };
- /* nc */
- channel at 5 {
- reg = <5>;
- ti,gain = <3>;
- ti,datarate = <3>;
- };
-
- /* can1_l */
- channel at 6 {
- reg = <6>;
- ti,gain = <3>;
- ti,datarate = <3>;
- };
-
- /* can1_h */
- channel at 7 {
- reg = <7>;
- ti,gain = <3>;
- ti,datarate = <3>;
- };
- };
-
- rtc at 51 {
- compatible = "nxp,pcf8563";
- reg = <0x51>;
- };
-};
-
-&pcie {
- status = "okay";
-};
-
-&usbh1 {
- status = "disabled";
-};
-
-&vpu {
- status = "disabled";
-};
-
-&iomuxc {
- pinctrl_can1phy: can1phy {
- fsl,pins = <
- /* CAN1_SR */
- MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13070
- /* CAN1_TERM */
- MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0
- >;
- };
-
- pinctrl_ecspi1: ecspi1grp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
- MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
- MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
- /* CS */
- MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1
- >;
- };
-
- pinctrl_ecspi3: ecspi3grp {
- fsl,pins = <
- MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1
- MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1
- MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1
- MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x000b1
- >;
- };
-
- pinctrl_leds: ledsgrp {
- fsl,pins = <
- MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
- >;
- };
-
- pinctrl_nfc: nfcgrp {
- fsl,pins = <
- /* NFC_ASK_OOK */
- MX6QDL_PAD_DISP0_DAT15__GPIO5_IO09 0x100b1
- /* NFC_PWR_EN */
- MX6QDL_PAD_DISP0_DAT16__GPIO5_IO10 0x100b1
- /* NFC_EN2 */
- MX6QDL_PAD_DISP0_DAT17__GPIO5_IO11 0x100b1
- /* NFC_EN */
- MX6QDL_PAD_DISP0_DAT18__GPIO5_IO12 0x100b1
- /* NFC_MOD */
- MX6QDL_PAD_DISP0_DAT19__GPIO5_IO13 0x100b1
- /* NFC_IRQ */
- MX6QDL_PAD_DISP0_DAT20__GPIO5_IO14 0x100b1
- >;
- };
-};
+#include <arm/imx6dl-prtrvt.dts>
+#include "imx6qdl-prti6q-nor.dtsi"
diff --git a/arch/arm/dts/imx6dl-prtvt7.dts b/arch/arm/dts/imx6dl-prtvt7.dts
index 27daa3e15f..b1fd13bdd7 100644
--- a/arch/arm/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/dts/imx6dl-prtvt7.dts
@@ -1,472 +1,5 @@
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-/*
- * Copyright (c) 2016 Protonic Holland
- */
-
+// SPDX-License-Identifier: GPL-2.0-or-later
/dts-v1/;
-#include <arm/imx6dl.dtsi>
-#include "imx6qdl-prti6q.dtsi"
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/leds/common.h>
-#include <dt-bindings/sound/fsl-imx-audmux.h>
-
-/ {
- model = "Protonic VT7";
- compatible = "prt,prtvt7", "fsl,imx6dl";
-
- memory at 10000000 {
- device_type = "memory";
- reg = <0x10000000 0x20000000>;
- };
-
- backlight_lcd: backlight-lcd {
- compatible = "pwm-backlight";
- pwms = <&pwm1 0 500000 0>;
- brightness-levels = <0 20 81 248 1000>;
- default-brightness-level = <20>;
- num-interpolated-steps = <21>;
- power-supply = <®_12v_bl>;
- enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
- };
-
- display {
- compatible = "fsl,imx-parallel-display";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ipu1_disp>;
- #address-cells = <1>;
- #size-cells = <0>;
- interface-pix-fmt = "rgb24";
- status = "okay";
-
- port at 0 {
- reg = <0>;
-
- display_in: endpoint {
- remote-endpoint = <&ipu1_di0_disp0>;
- };
- };
-
- port at 1 {
- reg = <1>;
-
- display_out: endpoint {
- remote-endpoint = <&panel_in>;
- };
- };
- };
-
- keys {
- compatible = "gpio-keys";
- autorepeat;
-
- esc {
- label = "GPIO Key ESC";
- linux,code = <KEY_ESC>;
- gpios = <&gpio_pca 0 GPIO_ACTIVE_LOW>;
- };
-
- up {
- label = "GPIO Key UP";
- linux,code = <KEY_UP>;
- gpios = <&gpio_pca 1 GPIO_ACTIVE_LOW>;
- };
-
- down {
- label = "GPIO Key DOWN";
- linux,code = <KEY_DOWN>;
- gpios = <&gpio_pca 4 GPIO_ACTIVE_LOW>;
- };
-
- enter {
- label = "GPIO Key Enter";
- linux,code = <KEY_ENTER>;
- gpios = <&gpio_pca 3 GPIO_ACTIVE_LOW>;
- };
-
- cycle {
- label = "GPIO Key CYCLE";
- linux,code = <KEY_CYCLEWINDOWS>;
- gpios = <&gpio_pca 2 GPIO_ACTIVE_LOW>;
- };
-
- f1 {
- label = "GPIO Key F1";
- linux,code = <KEY_F1>;
- gpios = <&gpio_pca 14 GPIO_ACTIVE_LOW>;
- };
-
- f2 {
- label = "GPIO Key F2";
- linux,code = <KEY_F2>;
- gpios = <&gpio_pca 13 GPIO_ACTIVE_LOW>;
- };
-
- f3 {
- label = "GPIO Key F3";
- linux,code = <KEY_F3>;
- gpios = <&gpio_pca 12 GPIO_ACTIVE_LOW>;
- };
-
- f4 {
- label = "GPIO Key F4";
- linux,code = <KEY_F4>;
- gpios = <&gpio_pca 11 GPIO_ACTIVE_LOW>;
- };
-
- f5 {
- label = "GPIO Key F5";
- linux,code = <KEY_F5>;
- gpios = <&gpio_pca 10 GPIO_ACTIVE_LOW>;
- };
-
- f6 {
- label = "GPIO Key F6";
- linux,code = <KEY_F6>;
- gpios = <&gpio_pca 5 GPIO_ACTIVE_LOW>;
- };
-
- f7 {
- label = "GPIO Key F7";
- linux,code = <KEY_F7>;
- gpios = <&gpio_pca 6 GPIO_ACTIVE_LOW>;
- };
-
- f8 {
- label = "GPIO Key F8";
- linux,code = <KEY_F8>;
- gpios = <&gpio_pca 7 GPIO_ACTIVE_LOW>;
- };
-
- f9 {
- label = "GPIO Key F9";
- linux,code = <KEY_F9>;
- gpios = <&gpio_pca 8 GPIO_ACTIVE_LOW>;
- };
-
- f10 {
- label = "GPIO Key F10";
- linux,code = <KEY_F10>;
- gpios = <&gpio_pca 9 GPIO_ACTIVE_LOW>;
- };
- };
-
- leds {
- compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_leds>;
-
- led-debug0 {
- function = LED_FUNCTION_STATUS;
- gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "heartbeat";
- };
- };
-
- panel {
- compatible = "innolux,g070y2t0ec";
- backlight = <&backlight_lcd>;
-
- port {
- panel_in: endpoint {
- remote-endpoint = <&display_out>;
- };
- };
- };
-
- reg_12v_bl: regulator-bl-12v {
- compatible = "regulator-fixed";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_reg_12v_bl>;
- regulator-name = "12v-bl";
- regulator-min-microvolt = <12000000>;
- regulator-max-microvolt = <12000000>;
- gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
- reg_1v8: regulator-1v8 {
- compatible = "regulator-fixed";
- regulator-name = "1v8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- sound {
- compatible = "simple-audio-card";
- simple-audio-card,name = "prti6q-sgtl5000";
- simple-audio-card,format = "i2s";
- simple-audio-card,widgets =
- "Microphone", "Microphone Jack",
- "Line", "Line In Jack",
- "Headphone", "Headphone Jack",
- "Speaker", "External Speaker";
- simple-audio-card,routing =
- "MIC_IN", "Microphone Jack",
- "LINE_IN", "Line In Jack",
- "Headphone Jack", "HP_OUT",
- "External Speaker", "LINE_OUT";
-
- simple-audio-card,cpu {
- sound-dai = <&ssi1>;
- system-clock-frequency = <0>;
- };
-
- simple-audio-card,codec {
- sound-dai = <&sgtl5000>;
- bitclock-master;
- frame-master;
- };
- };
-};
-
-&clks {
- assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>;
- assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>;
-};
-
-&ecspi2 {
- cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ecspi2>;
- status = "okay";
-
- tsc at 0 {
- compatible = "ti,tsc2046";
- reg = <0>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_tsc>;
- spi-max-frequency = <100000>;
- interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
- pendown-gpio = <&gpio3 20 GPIO_ACTIVE_HIGH>;
- vcc-supply = <®_3v3>;
-
- ti,vref-delay-usecs = /bits/ 16 <100>;
-
- ti,x-min = /bits/ 16 <0>;
- ti,x-max = /bits/ 16 <8000>;
- ti,y-min = /bits/ 16 <0>;
- ti,y-max = /bits/ 16 <4800>;
- ti,x-plate-ohms = /bits/ 16 <800>;
- ti,y-plate-ohms = /bits/ 16 <300>;
- ti,pressure-max = /bits/ 16 <4095>;
-
- ti,skip-samples = <2>;
- ti,sample-period-msecs = <10>;
- ti,report-period-msecs = <30>;
-
- ti,filter-tolerance = <80>;
- ti,touch-resistance-threshold = <3500>;
- };
-};
-
-&audmux {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_audmux>;
- status = "okay";
-
- mux_ssi1 {
- fsl,audmux-port = <0>;
- fsl,port-config = <
- IMX_AUDMUX_V2_PTCR_SYN 0
- IMX_AUDMUX_V2_PTCR_TFSEL(2) 0
- IMX_AUDMUX_V2_PTCR_TCSEL(2) 0
- IMX_AUDMUX_V2_PTCR_TFSDIR 0
- IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2)
- >;
- };
-
- mux_pins3 {
- fsl,audmux-port = <2>;
- fsl,port-config = <
- IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0)
- 0 IMX_AUDMUX_V2_PDCR_TXRXEN
- >;
- };
-};
-
-&can1 {
- pinctrl-0 = <&pinctrl_can1 &pinctrl_can1phy>;
-};
-
-&i2c1 {
- sgtl5000: codec at a {
- compatible = "fsl,sgtl5000";
- reg = <0xa>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_codec>;
- #sound-dai-cells = <0>;
- clocks = <&clks 201>;
- VDDA-supply = <®_3v3>;
- VDDIO-supply = <®_3v3>;
- VDDD-supply = <®_1v8>;
- };
-};
-
-&i2c3 {
- rtc at 51 {
- compatible = "nxp,pcf8563";
- reg = <0x51>;
- };
-
- gpio_pca: gpio at 74 {
- compatible = "nxp,pca9539";
- reg = <0x74>;
- interrupts-extended = <&gpio4 5 IRQ_TYPE_LEVEL_LOW>;
- #gpio-cells = <2>;
- gpio-controller;
- };
-};
-
-&ipu1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ipu1_csi0>;
- status = "okay";
-};
-
-&ipu1_di0_disp0 {
- remote-endpoint = <&display_in>;
-};
-
-&pwm1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_pwm1>;
- status = "okay";
-};
-
-&snvs_poweroff {
- status = "okay";
-};
-
-&snvs_pwrkey {
- status = "okay";
-};
-
-&ssi1 {
- #sound-dai-cells = <0>;
- fsl,mode = "i2s-slave";
- status = "okay";
-};
-
-&usbh1 {
- status = "disabled";
-};
-
-&vpu {
- status = "disabled";
-};
-
-&iomuxc {
- pinctrl_audmux: audmuxgrp {
- fsl,pins = <
- MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0
- MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
- MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
- MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
- MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
- >;
- };
-
- pinctrl_can1phy: can1phy {
- fsl,pins = <
- /* CAN1_SR */
- MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13070
- /* CAN1_TERM */
- MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0
- >;
- };
-
- pinctrl_codec: codecgrp {
- fsl,pins = <
- /* AUDIO_nRESET */
- MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x1f0b0
- >;
- };
-
- pinctrl_ecspi2: ecspi2grp {
- fsl,pins = <
- MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
- MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
- MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
- MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x000b1
- >;
- };
-
- pinctrl_ipu1_csi0: ipu1csi0grp {
- fsl,pins = <
- MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0
- MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x1b0b0
- MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x1b0b0
- MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x1b0b0
- MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x1b0b0
- MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x1b0b0
- MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x1b0b0
- MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x1b0b0
- MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0
- /* ITU656_nRESET */
- MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
- /* ITU656_nPDN */
- MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b0b0
- >;
- };
-
- pinctrl_ipu1_disp: ipudisp1grp {
- fsl,pins = <
- MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0xb0
- MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0xb0
-
- MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0xb0
- MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0xb0
- MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0xb0
- MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0xb0
- MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0xb0
- MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0xb0
- MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0xb0
- MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0xb0
-
- MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0xb0
- MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0xb0
- MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0xb0
- MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0xb0
- MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0xb0
- MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0xb0
- MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0xb0
- MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0xb0
-
- MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0xb0
- MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0xb0
- MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0xb0
- MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0xb0
- MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0xb0
- MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0xb0
- MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0xb0
- MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0xb0
- >;
- };
-
- pinctrl_leds: ledsgrp {
- fsl,pins = <
- MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
- >;
- };
-
- pinctrl_pwm1: pwm1grp {
- fsl,pins = <
- MX6QDL_PAD_GPIO_9__PWM1_OUT 0x1b0b0
- >;
- };
-
- pinctrl_reg_12v_bl: 12blgrp {
- fsl,pins = <
- MX6QDL_PAD_GPIO_7__GPIO1_IO07 0x1b0b0
- >;
- };
-
- pinctrl_tsc: tscgrp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b0
- MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0
- >;
- };
-};
+#include <arm/imx6dl-prtvt7.dts>
+#include "imx6qdl-prti6q-emmc.dtsi"
diff --git a/arch/arm/dts/imx6dl-victgo.dts b/arch/arm/dts/imx6dl-victgo.dts
index 55bc4c8d41..250cd761d4 100644
--- a/arch/arm/dts/imx6dl-victgo.dts
+++ b/arch/arm/dts/imx6dl-victgo.dts
@@ -1,145 +1,5 @@
// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (c) 2016 Protonic Holland
- */
-
/dts-v1/;
-#include <arm/imx6dl.dtsi>
-#include "imx6qdl-vicut1.dtsi"
-#include <dt-bindings/input/input.h>
-
-/ {
- model = "Kverneland Tellus GO";
- compatible = "kvg,victgo", "fsl,imx6dl";
-
- memory {
- reg = <0x10000000 0x20000000>;
- };
-
- rotary-encoder {
- compatible = "rotary-encoder";
- pinctrl-0 = <&pinctrl_rotary_ch>;
- gpios = <&gpio2 3 0>, <&gpio2 4 0>;
- linux,axis = <8>; /* REL_WHEEL */
- rotary-encoder,steps-per-period = <4>;
- rotary-encoder,relative-axis;
- rotary-encoder,rollover;
- wakeup-source;
- };
-
- rotary-button {
- compatible = "gpio-keys";
- pinctrl-0 = <&pinctrl_rotary_btn>;
- #address-cells = <1>;
- #size-cells = <0>;
- autorepeat;
- button at 0 {
- label = "Rotary Key";
- gpios = <&gpio2 05 1>;
- linux,code = <KEY_ENTER>;
- gpio-key,wakeup;
- };
- };
-};
-
-&fec {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_enet>;
- phy-mode = "rmii";
- phy-reset-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
- clocks = <&clks IMX6QDL_CLK_ENET>,
- <&clks IMX6QDL_CLK_ENET>;
- clock-names = "ipg", "ahb";
- status = "okay";
-};
-
-&uart2 {
- status = "disabled";
-};
-
-&i2c1 {
- ht16k33: ht16k33 at 70 {
- compatible = "holtek,ht16k33";
- pinctrl-0 = <&pinctrl_ht16k33>;
- reg = <0x70>;
- refresh-rate-hz = <20>;
- debounce-delay-ms = <50>;
- interrupt-parent = <&gpio4>;
- interrupts = <5 (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING)>;
- keypad,num-rows = <12>;
- keypad,num-columns = <3>;
- linux,keymap = <
- MATRIX_KEY(2, 0, KEY_F6)
- MATRIX_KEY(3, 0, KEY_F8)
- MATRIX_KEY(4, 0, KEY_F10)
- MATRIX_KEY(5, 0, KEY_F4)
- MATRIX_KEY(6, 0, KEY_F2)
- MATRIX_KEY(2, 1, KEY_F5)
- MATRIX_KEY(3, 1, KEY_F7)
- MATRIX_KEY(4, 1, KEY_F9)
- MATRIX_KEY(5, 1, KEY_F3)
- MATRIX_KEY(6, 1, KEY_F1)
- >;
- };
-};
-
-&pwm2 {
- status = "disabled";
-};
-
-&iomuxc {
- pinctrl_enet: enetgrp {
- fsl,pins = <
- /* MX6QDL_ENET_PINGRP4 */
- MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
- MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
- MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
- MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
- MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0
- MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
- MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
- MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
- MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
- MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0
- /* Phy reset */
- MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26 0x1b0b0
- /* nINTRP */
- MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30 0x1b0b0
- >;
- };
-
- pinctrl_ecspi2: ecspi2grp {
- fsl,pins = <
- MX6QDL_PAD_DISP0_DAT16__ECSPI2_MOSI 0x100b1
- MX6QDL_PAD_DISP0_DAT17__ECSPI2_MISO 0x100b1
- MX6QDL_PAD_DISP0_DAT18__GPIO5_IO12 0x100b1
- MX6QDL_PAD_DISP0_DAT19__ECSPI2_SCLK 0x100b1
- >;
- };
-
- pinctrl_rotary_ch: rotarygrp {
- fsl,pins = <
- MX6QDL_PAD_NANDF_D3__GPIO2_IO03 0x1b0b0 /* ROTARY_A */
- MX6QDL_PAD_NANDF_D4__GPIO2_IO04 0x1b0b0 /* ROTARY_B */
- >;
- };
-
- pinctrl_rotary_btn: rotarygrp {
- fsl,pins = <
- MX6QDL_PAD_NANDF_D5__GPIO2_IO05 0x1b0b0 /* ROTARY_BTN */
- >;
- };
-
- pinctrl_ht16k33: ht16k33grp {
- fsl,pins = <
- MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x1b0b0 /* IRQ */
- >;
- };
- pinctrl_tsc2046e: tsc2046egrp {
- fsl,pins = <
- MX6QDL_PAD_DISP0_DAT14__GPIO5_IO08 0x1b0b0
- MX6QDL_PAD_DISP0_DAT15__GPIO5_IO09 0x1b0b0
- >;
- };
-};
+#include <arm/imx6dl-victgo.dts>
+#include "imx6qdl-prti6q-nor.dtsi"
diff --git a/arch/arm/dts/imx6dl-vicut1.dts b/arch/arm/dts/imx6dl-vicut1.dts
index 725acbefc5..99cc7af2e6 100644
--- a/arch/arm/dts/imx6dl-vicut1.dts
+++ b/arch/arm/dts/imx6dl-vicut1.dts
@@ -1,51 +1,5 @@
// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (c) 2014 Protonic Holland
- */
-
/dts-v1/;
-#include <arm/imx6dl.dtsi>
-#include "imx6qdl-vicut1.dtsi"
-
-/ {
- model = "Kverneland UT1 Board";
- compatible = "kvg,vicut1", "fsl,imx6dl";
-
- memory {
- reg = <0x10000000 0x80000000>;
- };
-};
-
-&fec {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_enet>;
- phy-mode = "rgmii";
- status = "okay";
-};
-
-&iomuxc {
- pinctrl_enet: enetgrp {
- fsl,pins = <
- /* MX6QDL_ENET_PINGRP_RGMII_MD(0x1b030, 0x10030) */
- MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
- MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
- MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
- MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
- MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
- MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
- MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
- MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
- MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
- MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
- MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
- MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
- MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
- MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
- MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
- /* Phy reset */
- MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
- MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
- >;
- };
-};
+#include <arm/imx6dl-vicut1.dts>
+#include "imx6qdl-prti6q-nor.dtsi"
diff --git a/arch/arm/dts/imx6q-prti6q.dts b/arch/arm/dts/imx6q-prti6q.dts
index 21e24222a0..71606b892c 100644
--- a/arch/arm/dts/imx6q-prti6q.dts
+++ b/arch/arm/dts/imx6q-prti6q.dts
@@ -1,532 +1,5 @@
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-/*
- * Copyright (c) 2014 Protonic Holland
- */
-
+// SPDX-License-Identifier: GPL-2.0-or-later
/dts-v1/;
-#include <arm/imx6q.dtsi>
-#include "imx6qdl-prti6q.dtsi"
-#include "imx6qdl-prti6q-nor.dtsi"
-#include <dt-bindings/leds/common.h>
-#include <dt-bindings/sound/fsl-imx-audmux.h>
-
-/ {
- model = "Protonic PRTI6Q board";
- compatible = "prt,prti6q", "fsl,imx6q";
-
- memory at 10000000 {
- device_type = "memory";
- reg = <0x10000000 0xf0000000>;
- };
-
- backlight_lcd: backlight-lcd {
- compatible = "pwm-backlight";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_backlight>;
- pwms = <&pwm1 0 5000000 0>;
- brightness-levels = <0 16 64 255>;
- num-interpolated-steps = <16>;
- default-brightness-level = <16>;
- power-supply = <®_3v3>;
- enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
- };
-
- can3_25m_osc: can3-25m-osc {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <25000000>;
- };
-
- leds {
- compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_leds>;
-
- led-debug0 {
- function = LED_FUNCTION_STATUS;
- gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "heartbeat";
- };
-
- led-debug1 {
- function = LED_FUNCTION_SD;
- gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "disk-activity";
- };
- };
-
- panel {
- compatible = "kyo,tcg121xglp";
- backlight = <&backlight_lcd>;
-
- port {
- panel_in: endpoint {
- remote-endpoint = <&lvds0_out>;
- };
- };
- };
-
- reg_wifi: regulator-wifi {
- compatible = "regulator-fixed";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_wifi_npd>;
- enable-active-high;
- gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
- regulator-max-microvolt = <1800000>;
- regulator-min-microvolt = <1800000>;
- regulator-name = "regulator-WL12xx";
- startup-delay-us = <70000>;
- };
-
- sound {
- compatible = "simple-audio-card";
- simple-audio-card,name = "prti6q-sgtl5000";
- simple-audio-card,format = "i2s";
- simple-audio-card,widgets =
- "Microphone", "Microphone Jack",
- "Line", "Line In Jack",
- "Headphone", "Headphone Jack",
- "Speaker", "External Speaker";
- simple-audio-card,routing =
- "MIC_IN", "Microphone Jack",
- "LINE_IN", "Line In Jack",
- "Headphone Jack", "HP_OUT",
- "External Speaker", "LINE_OUT";
-
- simple-audio-card,cpu {
- sound-dai = <&ssi1>;
- system-clock-frequency = <0>;
- };
-
- simple-audio-card,codec {
- sound-dai = <&sgtl5000>;
- bitclock-master;
- frame-master;
- };
- };
-
- sound-spdif {
- compatible = "fsl,imx-audio-spdif";
- model = "imx-spdif";
- spdif-controller = <&spdif>;
- spdif-in;
- spdif-out;
- };
-};
-
-&audmux {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_audmux>;
- status = "okay";
-
- mux_ssi1 {
- fsl,audmux-port = <0>;
- fsl,port-config = <
- IMX_AUDMUX_V2_PTCR_SYN 0
- IMX_AUDMUX_V2_PTCR_TFSEL(2) 0
- IMX_AUDMUX_V2_PTCR_TCSEL(2) 0
- IMX_AUDMUX_V2_PTCR_TFSDIR 0
- IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2)
- >;
- };
-
- mux_pins3 {
- fsl,audmux-port = <2>;
- fsl,port-config = <
- IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0)
- 0 IMX_AUDMUX_V2_PDCR_TXRXEN
- >;
- };
-};
-
-&can2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_can2>;
- status = "okay";
-};
-
-&ecspi1 {
- cs-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ecspi1>;
- status = "okay";
-
- flash at 0 {
- compatible = "jedec,spi-nor";
- reg = <0>;
- spi-max-frequency = <20000000>;
- #address-cells = <1>;
- #size-cells = <1>;
- };
-};
-
-&ecspi2 {
- cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>, <&gpio4 25 GPIO_ACTIVE_HIGH>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ecspi2 &pinctrl_ecspi2_cs>;
- status = "okay";
-
- can at 0 {
- compatible = "microchip,mcp2515";
- reg = <0>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_can3>;
- clocks = <&can3_25m_osc>;
- interrupts-extended = <&gpio3 20 IRQ_TYPE_LEVEL_LOW>;
- spi-max-frequency = <5000000>;
- };
-
- adc at 1 {
- compatible = "ti,adc128s052";
- reg = <1>;
- spi-max-frequency = <2000000>;
- vref-supply = <®_3v3>;
- };
-};
-
-&ecspi3 {
- cs-gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ecspi3>;
- status = "okay";
-};
-
-&fec {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_enet>;
- phy-mode = "rgmii-id";
- phy-handle = <&rgmii_phy>;
- status = "okay";
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- /* Microchip KSZ9031RNX PHY */
- rgmii_phy: ethernet-phy at 4 {
- reg = <0>;
- interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
- reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
- reset-assert-us = <10000>;
- reset-deassert-us = <300>;
- };
- };
-};
-
-&hdmi {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_hdmi>;
- ddc-i2c-bus = <&i2c2>;
- status = "okay";
-};
-
-&i2c1 {
- sgtl5000: audio-codec at a {
- compatible = "fsl,sgtl5000";
- reg = <0xa>;
- #sound-dai-cells = <0>;
- clocks = <&clks 201>;
- VDDA-supply = <®_3v3>;
- VDDIO-supply = <®_3v3>;
- VDDD-supply = <®_1v8>;
- };
-};
-
-/* DDC */
-&i2c2 {
- clock-frequency = <100000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c2>;
- status = "okay";
-};
-
-&i2c3 {
- adc at 49 {
- compatible = "ti,ads1015";
- reg = <0x49>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- /* can2_l */
- channel at 4 {
- reg = <4>;
- ti,gain = <3>;
- ti,datarate = <3>;
- };
-
- /* can2_h */
- channel at 5 {
- reg = <5>;
- ti,gain = <3>;
- ti,datarate = <3>;
- };
-
- /* can1_l */
- channel at 6 {
- reg = <6>;
- ti,gain = <3>;
- ti,datarate = <3>;
- };
-
- /* can1_h */
- channel at 7 {
- reg = <7>;
- ti,gain = <3>;
- ti,datarate = <3>;
- };
- };
-};
-&pcie {
- status = "okay";
-};
-
-&pwm1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_pwm1>;
- status = "okay";
-};
-
-&ldb {
- status = "okay";
-
- lvds-channel at 0 {
- status = "okay";
-
- port at 4 {
- reg = <4>;
-
- lvds0_out: endpoint {
- remote-endpoint = <&panel_in>;
- };
- };
- };
-};
-
-&sata {
- status = "okay";
-};
-
-&snvs_poweroff {
- status = "okay";
-};
-
-&spdif {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_spdif>;
- status = "okay";
-};
-
-&ssi1 {
- #sound-dai-cells = <0>;
- fsl,mode = "ac97-slave";
- status = "okay";
-};
-
-&uart2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart2>;
- status = "okay";
-};
-
-&uart5 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart5>;
- status = "okay";
-};
-
-&usbotg {
- pinctrl-0 = <&pinctrl_usbotg &pinctrl_usbotg_id>;
-};
-
-&usdhc2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc2>;
- non-removable;
- vmmc-supply = <®_wifi>;
- cap-power-off-card;
- keep-power-in-suspend;
- status = "okay";
-
- wifi {
- compatible = "ti,wl1271";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_wifi>;
- interrupts-extended = <&gpio1 30 IRQ_TYPE_LEVEL_HIGH>;
- ref-clock-frequency = "38400000";
- tcxo-clock-frequency = "19200000";
- };
-};
-
-&iomuxc {
- pinctrl_audmux: audmuxgrp {
- fsl,pins = <
- MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0
- MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
- MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
- MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
- MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
- >;
- };
-
- pinctrl_backlight: backlightgrp {
- fsl,pins = <
- MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28 0x1b0b0
- >;
- };
-
- pinctrl_can2: can2grp {
- fsl,pins = <
- MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x80000000
- MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x80000000
- >;
- };
-
- pinctrl_can3: can3grp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b1
- >;
- };
-
- pinctrl_ecspi1: ecspi1grp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
- MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
- MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
- /* CS */
- MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1
- >;
- };
-
- pinctrl_ecspi2: ecspi2grp {
- fsl,pins = <
- MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
- MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
- MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
- MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x000b1
- >;
- };
-
- pinctrl_ecspi2_cs: ecspi2csgrp {
- fsl,pins = <
- /* ADC128S022 CS */
- MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25 0x1b0b1
- >;
- };
-
- pinctrl_ecspi3: ecspi3grp {
- fsl,pins = <
- MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1
- MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1
- MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1
- MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x000b1
- >;
- };
-
- pinctrl_enet: enetgrp {
- fsl,pins = <
- MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
- MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
- MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
- MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
- MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
- MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
- MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
- MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
- MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
- MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
- MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
- MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
- MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
- MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
- MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
-
- /* Phy reset */
- MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
- MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
- >;
- };
-
- pinctrl_hdmi: hdmigrp {
- fsl,pins = <
- /* NOTE: DDC is done via I2C2, so DON'T
- * configure DDC pins for HDMI!
- */
- MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE 0x1f8b0
- >;
- };
-
- /* DDC */
- pinctrl_i2c2: i2c2grp {
- fsl,pins = <
- MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
- MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
- >;
- };
-
- pinctrl_leds: ledsgrp {
- fsl,pins = <
- MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
- MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0
- >;
- };
-
- pinctrl_pwm1: pwm1grp {
- fsl,pins = <
- MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0
- >;
- };
-
- pinctrl_spdif: spdifgrp {
- fsl,pins = <
- MX6QDL_PAD_GPIO_16__SPDIF_IN 0x1b0b0
- MX6QDL_PAD_GPIO_19__SPDIF_OUT 0x1b0b0
- >;
- };
-
- pinctrl_uart2: uart2grp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D26__UART2_RX_DATA 0x1b0b1
- MX6QDL_PAD_EIM_D27__UART2_TX_DATA 0x1b0b1
- MX6QDL_PAD_EIM_D28__UART2_DTE_CTS_B 0x1b0b1
- MX6QDL_PAD_EIM_D29__UART2_DTE_RTS_B 0x1b0b1
- >;
- };
-
- pinctrl_uart5: uart5grp {
- fsl,pins = <
- MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1
- MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1
- >;
- };
-
- pinctrl_usbotg_id: usbotgidgrp {
- fsl,pins = <
- MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x1f058
- >;
- };
-
- pinctrl_usdhc2: usdhc2grp {
- fsl,pins = <
- MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9
- MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9
- MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
- MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
- MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
- MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9
- >;
- };
-
- pinctrl_wifi: wifigrp {
- fsl,pins = <
- /* WL12xx IRQ */
- MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x10880
- >;
- };
-
- pinctrl_wifi_npd: wifinpd {
- fsl,pins = <
- MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1b8b0
- >;
- };
-};
+#include <arm/imx6q-prti6q.dts>
+#include "imx6qdl-prti6q-nor.dtsi"
diff --git a/arch/arm/dts/imx6q-prtwd2.dts b/arch/arm/dts/imx6q-prtwd2.dts
index 8572917865..78ea4bc15c 100644
--- a/arch/arm/dts/imx6q-prtwd2.dts
+++ b/arch/arm/dts/imx6q-prtwd2.dts
@@ -1,188 +1,5 @@
// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (c) 2018 Protonic Holland
- */
-
/dts-v1/;
-#include <arm/imx6q.dtsi>
-#include "imx6qdl-prti6q.dtsi"
-#include <dt-bindings/leds/common.h>
-
-/ {
- model = "Protonic WD2 board";
- compatible = "prt,prtwd2", "fsl,imx6q";
-
- memory at 10000000 {
- device_type = "memory";
- reg = <0x10000000 0x20000000>;
- };
-
- memory at 80000000 {
- device_type = "memory";
- reg = <0x80000000 0x20000000>;
- };
-
- usdhc2_wifi_pwrseq: usdhc2_wifi_pwrseq {
- compatible = "mmc-pwrseq-simple";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_wifi_npd>;
- reset-gpios = <&gpio6 10 GPIO_ACTIVE_LOW>;
- };
-
- /* PRTWD2 rev 1 bitbang I2C for Ethernet Switch */
- i2c at 4 {
- compatible = "i2c-gpio";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c4>;
- sda-gpios = <&gpio1 22 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
- scl-gpios = <&gpio1 31 GPIO_ACTIVE_HIGH>;
- i2c-gpio,delay-us = <20>; /* ~10 kHz */
- i2c-gpio,scl-output-only;
- #address-cells = <1>;
- #size-cells = <0>;
- };
-};
-
-&can1 {
- pinctrl-0 = <&pinctrl_can1 &pinctrl_can1phy>;
-};
-
-&fec {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_enet>;
- phy-mode = "rmii";
- clocks = <&clks IMX6QDL_CLK_ENET>,
- <&clks IMX6QDL_CLK_ENET>;
- clock-names = "ipg", "ahb";
- status = "okay";
-
- fixed-link {
- speed = <100>;
- pause;
- full-duplex;
- };
-};
-
-&i2c3 {
- adc at 49 {
- compatible = "ti,ads1015";
- reg = <0x49>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- /* V in */
- channel at 4 {
- reg = <4>;
- ti,gain = <1>;
- ti,datarate = <3>;
- };
-
- /* I charge */
- channel at 5 {
- reg = <5>;
- ti,gain = <1>;
- ti,datarate = <3>;
- };
-
- /* V bus */
- channel at 6 {
- reg = <6>;
- ti,gain = <1>;
- ti,datarate = <3>;
- };
-
- /* nc */
- channel at 7 {
- reg = <7>;
- ti,gain = <1>;
- ti,datarate = <3>;
- };
- };
-};
-
-&usdhc2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc2>;
- non-removable;
- no-1-8-v;
- non-removable;
- mmc-pwrseq = <&usdhc2_wifi_pwrseq>;
- pm-ignore-notify;
- #address-cells = <1>;
- #size-cells = <0>;
- status = "okay";
-
- wifi at 1 {
- compatible = "brcm,bcm4329-fmac";
- reg = <1>;
- };
-};
-
-&iomuxc {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usb_eth_chg>;
-
- pinctrl_can1phy: can1phy {
- fsl,pins = <
- /* CAN1_SR */
- MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13070
- >;
- };
-
- pinctrl_enet: enetgrp {
- fsl,pins = <
- /* MX6QDL_ENET_PINGRP4 */
- MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
- MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
- MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x130b0
- MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
- MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
- MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
- MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
-
- MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0
- /* Phy reset */
- MX6QDL_PAD_CSI0_DAT4__GPIO5_IO22 0x1b0b0
- /* nINTRP */
- MX6QDL_PAD_CSI0_DAT5__GPIO5_IO23 0x1b0b0
-
- MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
- MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
- >;
- };
-
- pinctrl_i2c4: i2c4grp {
- fsl,pins = <
- MX6QDL_PAD_ENET_MDIO__GPIO1_IO22 0x1f8b0
- MX6QDL_PAD_ENET_MDC__GPIO1_IO31 0x1f8b0
- >;
- };
-
- pinctrl_usb_eth_chg: usbethchggrp {
- fsl,pins = <
- /* USB charging control */
- MX6QDL_PAD_NANDF_CS0__GPIO6_IO11 0x130b0
- MX6QDL_PAD_NANDF_CS1__GPIO6_IO14 0x130b0
- MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x130b0
- MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0x130b0
- >;
- };
-
- pinctrl_usdhc2: usdhc2grp {
- fsl,pins = <
- MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9
- MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9
- MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
- MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
- MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
- MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9
- >;
- };
- pinctrl_wifi_npd: wifinpd {
- fsl,pins = <
- /* WL_REG_ON */
- MX6QDL_PAD_NANDF_RB0__GPIO6_IO10 0x13069
- >;
- };
-};
+#include <arm/imx6q-prtwd2.dts>
+#include "imx6qdl-prti6q-emmc.dtsi"
diff --git a/arch/arm/dts/imx6q-vicut1.dts b/arch/arm/dts/imx6q-vicut1.dts
index 9d1d6fa550..61fb56d401 100644
--- a/arch/arm/dts/imx6q-vicut1.dts
+++ b/arch/arm/dts/imx6q-vicut1.dts
@@ -1,66 +1,5 @@
// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (c) 2014 Protonic Holland
- */
-
/dts-v1/;
-#include <arm/imx6q.dtsi>
-#include "imx6qdl-vicut1.dtsi"
-
-/ {
- model = "Kverneland UT1Q Board";
- compatible = "kvg,vicut1q", "fsl,imx6q";
-
- memory {
- reg = <0x10000000 0xf0000000>;
- };
-};
-
-&fec {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_enet>;
- phy-mode = "rgmii-id";
- phy-handle = <&rgmii_phy>;
- status = "okay";
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- /* Microchip KSZ9031RNX PHY */
- rgmii_phy: ethernet-phy at 4 {
- reg = <0>;
- interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
- reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
- reset-assert-us = <10000>;
- reset-deassert-us = <300>;
- };
- };
-};
-
-&iomuxc {
- pinctrl_enet: enetgrp {
- fsl,pins = <
- /* MX6QDL_ENET_PINGRP_RGMII_MD(0x1b030, 0x10030) */
- MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
- MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
- MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
- MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
- MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
- MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
- MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
- MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
- MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
- MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
- MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
- MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
- MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
- MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
- MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
- /* Phy reset */
- MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
- MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
- >;
- };
-};
+#include <arm/imx6q-vicut1.dts>
+#include "imx6qdl-prti6q-nor.dtsi"
diff --git a/arch/arm/dts/imx6qdl-prti6q-emmc.dtsi b/arch/arm/dts/imx6qdl-prti6q-emmc.dtsi
new file mode 100644
index 0000000000..4fc7bd6473
--- /dev/null
+++ b/arch/arm/dts/imx6qdl-prti6q-emmc.dtsi
@@ -0,0 +1,49 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/ {
+ chosen {
+ stdout-path = &uart4;
+
+ environment at 0 {
+ compatible = "barebox,environment";
+ device-path = &usdhc3, "partname:barebox-environment";
+ };
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ /* Address will be determined by the bootloader */
+ ramoops {
+ compatible = "ramoops";
+ };
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ /* Address will be determined by the bootloader */
+ ramoops {
+ compatible = "ramoops";
+ };
+ };
+};
+
+&usdhc3 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 40000 {
+ label = "barebox-environment";
+ reg = <0x40000 0x80000>;
+ };
+
+ partition at c0000 {
+ label = "state";
+ reg = <0xc0000 0x40000>;
+ };
+};
diff --git a/arch/arm/dts/imx6qdl-prti6q-nor.dtsi b/arch/arm/dts/imx6qdl-prti6q-nor.dtsi
index ad718ce421..7a88652b42 100644
--- a/arch/arm/dts/imx6qdl-prti6q-nor.dtsi
+++ b/arch/arm/dts/imx6qdl-prti6q-nor.dtsi
@@ -1,7 +1,12 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+#include "imx6qdl-prti6q-emmc.dtsi"
+
&ecspi1 {
flash at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+
partition at 0 {
label = "barebox";
reg = <0x0 0x100000>;
diff --git a/arch/arm/dts/imx6qdl-prti6q.dtsi b/arch/arm/dts/imx6qdl-prti6q.dtsi
deleted file mode 100644
index bfc059e34f..0000000000
--- a/arch/arm/dts/imx6qdl-prti6q.dtsi
+++ /dev/null
@@ -1,216 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-/*
- * Copyright (c) 2014 Protonic Holland
- */
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-
-/ {
- chosen {
- stdout-path = &uart4;
-
- environment-emmc {
- compatible = "barebox,environment";
- device-path = &usdhc3, "partname:barebox-environment";
- };
- };
-
- reserved-memory {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- /* Address will be determined by the bootloader */
- ramoops {
- compatible = "ramoops";
- };
- };
-
- reserved-memory {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- /* Address will be determined by the bootloader */
- ramoops {
- compatible = "ramoops";
- };
- };
-
- reg_1v8: regulator-1v8 {
- compatible = "regulator-fixed";
- regulator-name = "1v8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- reg_3v3: regulator-3v3 {
- compatible = "regulator-fixed";
- regulator-name = "3v3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
- reg_usb_h1_vbus: regulator-h1-vbus {
- compatible = "regulator-fixed";
- regulator-name = "h1-vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- regulator-always-on;
- };
-
- reg_usb_otg_vbus: regulator-otg-vbus {
- compatible = "regulator-fixed";
- regulator-name = "otg-vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-};
-
-&can1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_can1>;
- status = "okay";
-};
-
-&i2c1 {
- clock-frequency = <100000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c1>;
- status = "okay";
-};
-
-&i2c3 {
- clock-frequency = <100000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c3>;
- status = "okay";
-
- temperature-sensor at 70 {
- compatible = "ti,tmp103";
- reg = <0x70>;
- };
-};
-
-&uart4 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart4>;
- status = "okay";
-};
-
-&usbh1 {
- vbus-supply = <®_usb_h1_vbus>;
- phy_type = "utmi";
- dr_mode = "host";
- status = "okay";
-};
-
-&usbotg {
- vbus-supply = <®_usb_otg_vbus>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usbotg>;
- phy_type = "utmi";
- dr_mode = "host";
- disable-over-current;
- status = "okay";
-};
-
-&usdhc1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc1>;
- cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
- status = "okay";
-};
-
-&usdhc3 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc3>;
- bus-width = <8>;
- non-removable;
- no-sdio;
- no-sd;
- status = "okay";
-
- #address-cells = <1>;
- #size-cells = <1>;
-
- partition at 100000 {
- label = "barebox-environment";
- reg = <0x100000 0x100000>;
- };
-
- partition at 200000 {
- label = "state";
- reg = <0x200000 0x100000>;
- };
-};
-
-&iomuxc {
- pinctrl_can1: can1grp {
- fsl,pins = <
- MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x80000000
- MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x80000000
- >;
- };
-
- pinctrl_i2c1: i2c1grp {
- fsl,pins = <
- MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1
- MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1
- >;
- };
-
- pinctrl_i2c3: i2c3grp {
- fsl,pins = <
- MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
- MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
- >;
- };
-
- pinctrl_uart4: uart4grp {
- fsl,pins = <
- MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
- MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
- >;
- };
-
- pinctrl_usdhc1: usdhc1grp {
- fsl,pins = <
- MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9
- MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9
- MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9
- MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9
- MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9
- MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9
- MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0
- >;
- };
-
- pinctrl_usdhc3: usdhc3grp {
- fsl,pins = <
- MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
- MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099
- MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099
- MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099
- MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099
- MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099
- MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099
- MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099
- MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099
- MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
- MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1
- >;
- };
-
- pinctrl_usbotg: usbotggrp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
- MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
- >;
- };
-};
diff --git a/arch/arm/dts/imx6qdl-vicut1.dtsi b/arch/arm/dts/imx6qdl-vicut1.dtsi
deleted file mode 100644
index dbfcf2527c..0000000000
--- a/arch/arm/dts/imx6qdl-vicut1.dtsi
+++ /dev/null
@@ -1,234 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (c) 2014 Protonic Holland
- */
-
-#include "imx6qdl-prti6q.dtsi"
-#include "imx6qdl-prti6q-nor.dtsi"
-#include <dt-bindings/input/input.h>
-
-/ {
- gpio_key_pwr: gpio_keys {
- compatible = "gpio-keys";
- autorepeat;
-
- power {
- label = "GPIO Key Power";
- gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_POWER>;
- gpio-key,wakeup;
- };
- };
-
- leds {
- compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_leds>;
-
- debug0 {
- label = "debug0";
- gpios = <&gpio1 8 0>;
- linux,default-trigger = "heartbeat";
- };
-
- debug1 {
- label = "debug1";
- gpios = <&gpio1 9 0>;
- linux,default-trigger = "mmc";
- };
-
- power_led {
- label = "power_led";
- gpios = <&gpio2 24 0>;
- default-state = "on";
- };
-
- isb_led {
- label = "isb_led";
- gpios = <&gpio4 31 0>;
- default-state = "off";
- };
- };
-};
-
-&clks {
- assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>;
- assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>;
-};
-
-&uart1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart1>;
- status = "okay";
-};
-
-&uart3 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart3>;
- status = "okay";
-};
-
-&i2c3 {
- rtc: pcf8563 at 51 {
- compatible = "nxp,pcf8563";
- reg = <0x51>;
- };
-};
-
-&ecspi1 {
- cs-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ecspi1>;
- status = "okay";
-
- flash at 0 {
- compatible = "jedec,spi-nor";
- reg = <0>;
- spi-max-frequency = <20000000>;
- #address-cells = <1>;
- #size-cells = <1>;
- };
-};
-
-&iomuxc {
- pinctrl_hog: hoggrp {
- fsl,pins = <
- /* SGTL5000 sys_mclk */
- MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0
- /* CAN1_SR + CAN2_SR GPIO outputs */
- MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13070
- MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x13070
- /* CAN1_TERM */
- MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0
- /* ITU656_nRESET */
- MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
- /* CAM1_MIRROR */
- MX6QDL_PAD_GPIO_3__GPIO1_IO03 0x130b0
- /* CAM2_MIRROR */
- MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x130b0
- /* CAM_nDETECT */
- MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0
- /* nON_SWITCH */
- MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b0
- /* ISB_IN1 */
- MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x130b0
- /* ISB_nIN2 */
- MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x1b0b0
- /* WARN_LIGHT */
- MX6QDL_PAD_EIM_A19__GPIO2_IO19 0x100b0
- /* ON2_FB */
- MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x100b0
- /* YACO_nIRQ */
- MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x1b0b0
- /* YACO_BOOT0 */
- MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x130b0
- /* YACO_nRESET */
- MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x1b0b0
- /* FORCE_ON1 */
- MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0
- /* AUDIO_nRESET */
- MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x1f0b0
- /* ITU656_nPDN */
- MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b0b0
-
- /* HW revision detect */
- /* REV_ID0 */
- MX6QDL_PAD_SD4_DAT0__GPIO2_IO08 0x1b0b0
- /* REV_ID1 = PWM output LED_PWM (SION) */
- /* defined in &pinctrl_pwm3 */
- /* REV_ID2 */
- MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0
- /* REV_ID3 */
- MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x1b0b0
- /* REV_ID4 */
- MX6QDL_PAD_SD4_DAT4__GPIO2_IO12 0x1b0b0
-
- /* New in HW revision 1 */
- MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x100b0 /* ON1_FB */
- MX6QDL_PAD_DI0_PIN2__GPIO4_IO18 0x1b0b0 /* DIP1_FB */
-
- /* New in UTC (UT1 HW revision 1) and TGO */
- /* WHEEL */
- MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x100b0
- /* RADAR */
- MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x100b0
- /* PTO */
- MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x100b0
- /* CPU_ON1_CTRL */
- MX6QDL_PAD_DISP0_DAT0__GPIO4_IO21 0x1b0b0
- /* CPU_ON2_CTRL */
- MX6QDL_PAD_DISP0_DAT1__GPIO4_IO22 0x1b0b0
- /* CPU_HITCH_IN_OUT */
- MX6QDL_PAD_DISP0_DAT2__GPIO4_IO23 0x100b0
- /* CPU_LIGHT_ON */
- MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x100b0
- /* CPU_CONTACT_IN */
- MX6QDL_PAD_DISP0_DAT6__GPIO4_IO27 0x100b0
- >;
- };
-
- pinctrl_ecspi1: ecspi1grp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
- MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
- MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
- /* CS */
- MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1
- >;
- };
-
- pinctrl_usbotg: usbotggrp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
- /* power enable, high active */
- MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
- >;
- };
-
- /* YaCO AUX Uart */
- pinctrl_uart1: uart1grp {
- fsl,pins = <
- MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
- MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
- >;
- };
-
- /* YaCO Touchscreen UART */
- pinctrl_uart3: uart3grp {
- fsl,pins = <
- MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
- MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
- >;
- };
-
- pinctrl_leds: ledsgrp {
- fsl,pins = <
- /* DEBUG0A */
- MX6QDL_PAD_DI0_DISP_CLK__GPIO4_IO16 0x1b0b0
- /* DEBUG1A */
- MX6QDL_PAD_DI0_PIN15__GPIO4_IO17 0x1b0b0
- /* DEBUG0 */
- MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
- /* DEBUG1 */
- MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0
- /* POWER_LED */
- MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x1b0b0
- /* ISB_LED */
- MX6QDL_PAD_DISP0_DAT10__GPIO4_IO31 0x1b0b0
- >;
- };
-
- pinctrl_pwm2: pwm2grp {
- fsl,pins = <
- /* ISB LED (not in TGO or UTC version 1+) */
- MX6QDL_PAD_DISP0_DAT9__PWM2_OUT 0x1b0b0
- >;
- };
-
- pinctrl_pwm3: pwm3grp {
- fsl,pins = <
- /* REV_ID1 = PWM output LED_PWM (SION for ID) */
- MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x4001b0b0
- >;
- };
-};
diff --git a/arch/arm/dts/imx6qp-prtwd3.dts b/arch/arm/dts/imx6qp-prtwd3.dts
index 97b25ee26a..8c56d70b5a 100644
--- a/arch/arm/dts/imx6qp-prtwd3.dts
+++ b/arch/arm/dts/imx6qp-prtwd3.dts
@@ -1,675 +1,6 @@
-/*
- * Copyright (c) 2018 Protonic Holland
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 or later at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
- */
-
+// SPDX-License-Identifier: GPL-2.0-or-later
/dts-v1/;
-#include <arm/imx6qp.dtsi>
-#include "imx6qdl-prti6q.dtsi"
-
-/ {
- model = "Protonic WD3 board";
- compatible = "prt,prtwd3", "fsl,imx6qp";
-
- memory at 10000000 {
- device_type = "memory";
- reg = <0x10000000 0x20000000>;
- };
-
- memory at 80000000 {
- device_type = "memory";
- reg = <0x80000000 0x20000000>;
- };
-
- aliases {
- mdio-gpio0 = &mdio0;
- };
-
- usdhc2_wifi_pwrseq: usdhc2_wifi_pwrseq {
- compatible = "mmc-pwrseq-simple";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_wifi_npd>;
- reset-gpios = <&gpio6 10 GPIO_ACTIVE_LOW>;
- };
-
- clk20m_can: fdcan_clock {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <20000000>;
- };
-
- clk25m_switch: switch_clock {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <25000000>;
- };
-
- clk25m_phy3: phy3_clock {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <25000000>;
- };
-
- clk50m_phy: phy_clock {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <50000000>;
- };
-
- mdio0: mdio {
- compatible = "virtual,mdio-gpio";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_mdio0>;
-
- #address-cells = <1>;
- #size-cells = <0>;
- gpios = <&gpio5 6 GPIO_ACTIVE_HIGH
- &gpio5 7 GPIO_ACTIVE_HIGH>;
- };
-
- display_panel0 {
- compatible = "kyo,tcg121xglp";
- backlight = <&backlight_lcd>;
-
- port {
- display_panel0_in: endpoint {
- remote-endpoint = <&serializer0_out>;
- };
- };
- };
-
- display_panel1 {
- compatible = "kyo,tcg121xglp";
- backlight = <&backlight_panel1>;
-
- port {
- display_panel1_in: endpoint {
- remote-endpoint = <&serializer1_out>;
- };
- };
- };
-
- backlight_lcd: backlight_lcd {
- compatible = "pwm-backlight";
- pwms = <&pwm1 0 5000000 0>;
- brightness-levels = <0 1 2 4 6 8 12 16 24 32 48 64 96 128 192 255>;
- default-brightness-level = <15>;
- power-supply = <®_3v3>;
- };
-
- backlight_panel1: backlight_panel1 {
- compatible = "pwm-backlight";
- pwms = <&pwm2 0 5000000 0>;
- brightness-levels = <0 1 2 4 6 8 12 16 24 32 48 64 96 128 192 255>;
- default-brightness-level = <0>;
- power-supply = <®_3v3>;
- };
-};
-
-&fec {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_enet>;
- status = "okay";
-
- clocks = <&clks IMX6QDL_CLK_ENET>,
- <&clks IMX6QDL_CLK_ENET>,
- <&clks IMX6QDL_CLK_ENET_REF>,
- <&clks IMX6QDL_CLK_ENET_REF>;
- clock-names = "ipg", "ahb", "ptp", "enet_clk_ref";
- assigned-clocks = <&clks IMX6QDL_CLK_ENET_REF>;
- assigned-clock-rates = <125000000>;
-
- phy-mode = "rgmii";
- fixed-link {
- speed = <100>;
- full-duplex;
- };
-
- mdio1: mdio {
- #address-cells = <1>;
- #size-cells = <0>;
- /* Microchip KSZ9031 */
- rgmii_phy: ethernet-phy at 2 {
- compatible = "ethernet-phy-ieee802.3-c22";
- reg = <2>;
-
- interrupts-extended = <&gpio1 28 IRQ_TYPE_EDGE_FALLING>;
-
- /* FIXME: tx/rx clk skew are currently set by imx
- * platform driver. Write own walues here to not depend
- * fixup of horror.
- */
-
- reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
- /* reset assert time is provided by documentation */
- reset-assert-us = <10000>;
- /* documented reset deassert time (100us) is not enough
- * use test value of 300us.
- */
- reset-deassert-us = <1000>;
-
- clocks = <&clk25m_phy3>;
- };
- };
-};
-
-&ecspi2 {
- fsl,spi-num-chipselects = <1>;
- cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ecspi2>;
- status = "okay";
- sja1105_switch: sja1105 at 0 {
- reg = <0>;
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "nxp,sja1105q";
- spi-max-frequency = <4000000>;
- spi-cpha;
- spi-rx-delay-us = <1>;
- spi-tx-delay-us = <1>;
-
- reset-gpios = <&gpio5 5 GPIO_ACTIVE_LOW>;
-
- clocks = <&clk25m_switch>;
- #clock-cells = <1>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port at 0 {
- reg = <0>;
- label = "usb";
- phy-handle = <&usbeth_phy>;
- phy-mode = "rmii";
- };
-
- port at 1 {
- reg = <1>;
- label = "t1slave";
- phy-handle = <&tja1102_phy1>;
- phy-mode = "rmii";
- };
-
- port at 2 {
- reg = <2>;
- label = "t1master";
- phy-handle = <&tja1102_phy0>;
- phy-mode = "rmii";
-
- };
-
- port at 3 {
- reg = <3>;
- label = "rj45";
- phy-handle = <&rgmii_phy>;
- phy-mode = "rgmii-id";
- };
-
- port at 4 {
- reg = <4>;
- label = "cpu";
- ethernet = <&fec>;
- phy-mode = "rgmii-id";
-
- fixed-link {
- speed = <100>;
- full-duplex;
- };
- };
- };
- };
-};
-
-&mdio0 {
- usbeth_phy: ethernet-phy at 3 {
- compatible = "ethernet-phy-ieee802.3-c22";
- reg = <0x3>;
-
- interrupts-extended = <&gpio5 12 IRQ_TYPE_LEVEL_LOW>;
- micrel,led-mode = <0>;
-
- reset-gpios = <&gpio5 11 GPIO_ACTIVE_LOW>;
- reset-assert-us = <500>;
- reset-deassert-us = <1000>;
-
- /* FIXME: the clock is provided by switch and we should know
- * and we should request it only after switch have done clock
- * configuration. Since it is currently not implemented,
- * use fixed clock.
- * WARNING: Using fixed clocks in this case is potential source
- * for evil bugs. Switch may reconfigure, stop or change clk
- * freq without letting PHY to know about it.
- */
- clocks = <&clk50m_phy>;
- clock-names = "rmii-ref";
- };
-
- tja1102_phy0: ethernet-phy at 4 {
- compatible = "ethernet-phy-id0180.dc80";
- reg = <0x4>;
-
- interrupts-extended = <&gpio5 8 IRQ_TYPE_LEVEL_LOW>;
-
- reset-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
- /* reset detection time is 20 usec. */
- reset-assert-us = <20>;
- /* reset to standby 2 msec. */
- reset-deassert-us = <2000>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- tja1102_phy1: ethernet-phy at 5 {
- reg = <0x5>;
-
- interrupts-extended = <&gpio5 8 IRQ_TYPE_LEVEL_LOW>;
- };
- };
-};
-
-&ecspi3 {
- fsl,spi-num-chipselects = <1>;
- cs-gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ecspi3>;
- status = "okay";
- can3: can at 0 {
- compatible = "microchip,mcp2518fd";
- spi-max-frequency = <5000000>;
- reg = <0>;
- clocks = <&clk20m_can>;
- interrupt-parent = <&gpio4>;
- interrupts = <25 0x2>;
- };
-};
-
-&i2c1 {
- clock-frequency = <100000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c1>;
- status = "okay";
-
- serializer0: ds90ub927 at c {
- compatible = "ti,ds90ub927";
- reg = <0x0c>;
- #address-cells = <1>;
- #size-cells = <0>;
- port at 0 {
- reg = <0>;
- serializer0_in: endpoint {
- remote-endpoint = <&lvds0_out>;
- };
- };
- /* port at 1 {
- reg = <1>;
- serializer0_audio_in: endpoint {
- remote-endpoint = <&audio_i2s0_out>;
- };
- }; */
- port at 2 {
- reg = <2>;
- serializer0_out: endpoint {
- remote-endpoint = <&display_panel0_in>;
- };
- };
- };
-};
-
-&i2c2 {
- clock-frequency = <100000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c2>;
- status = "okay";
-
- serializer1: ds90ub927 at c {
- compatible = "ti,ds90ub927";
- reg = <0x0c>;
- #address-cells = <1>;
- #size-cells = <0>;
- port at 0 {
- reg = <0>;
- serializer1_in: endpoint {
- remote-endpoint = <&lvds1_out>;
- };
- };
- port at 2 {
- reg = <2>;
- serializer1_out: endpoint {
- remote-endpoint = <&display_panel1_in>;
- };
- };
- };
-
- camdeser: ds90ub954 at 30 {
- compatible = "ti,ds90ub954";
- reg = <0x30>;
- #address-cells = <1>;
- #size-cells = <0>;
- port at 0 {
- reg = <0>;
- camdeser_fpd_link_in: endpoint {
- };
- };
- port at 1 {
- reg = <1>;
- camdeser_mipi_out: endpoint {
- remote-endpoint = <&mipi_csi_in>;
- };
- };
- };
-};
-
-&usdhc2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc2>;
- no-1-8-v; /* force 3.3V VIO */
- non-removable;
- mmc-pwrseq = <&usdhc2_wifi_pwrseq>;
- pm-ignore-notify;
- status = "okay";
- #address-cells = <1>;
- #size-cells = <0>;
-
- brcmf: bcrmf at 1 {
- reg = <1>;
- compatible = "brcm,bcm4329-fmac";
- };
-};
-
-&i2c3 {
- adc at 49 {
- compatible = "ti,ads1015";
- reg = <0x49>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- channel at 4 {
- reg = <4>;
- ti,gain = <1>;
- ti,datarate = <3>;
- };
-
- channel at 5 {
- reg = <5>;
- ti,gain = <1>;
- ti,datarate = <3>;
- };
-
- channel at 6 {
- reg = <6>;
- ti,gain = <1>;
- ti,datarate = <3>;
- };
-
- channel at 7 {
- reg = <7>;
- ti,gain = <1>;
- ti,datarate = <3>;
- };
- };
-};
-
-&ldb {
- status = "okay";
-
- lvds-channel at 0 {
- status = "okay";
-
- port at 4 {
- reg = <4>;
-
- lvds0_out: endpoint {
- remote-endpoint = <&serializer0_in>;
- };
- };
- };
-
- lvds-channel at 1 {
- status = "okay";
-
- port at 4 {
- reg = <4>;
-
- lvds1_out: endpoint {
- remote-endpoint = <&serializer1_in>;
- };
- };
- };
-};
-
-&mipi_csi {
- status = "okay";
- port at 0 {
- reg = <0>;
-
- mipi_csi_in: endpoint {
- remote-endpoint = <&camdeser_mipi_out>;
- };
- };
-};
-
-&ipu1_csi0_mux_from_parallel_sensor {
- /* Empty, to disable parallel camera from PRTI6Q */
-};
-
-&pwm1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_pwm1>;
- status = "okay";
-};
-
-&pwm2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_pwm2>;
- status = "okay";
-};
-
-&iomuxc {
- pinctrl_enet: enetgrp {
- fsl,pins = <
- MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
- MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
- MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
- MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
- MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
- MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
- MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
- MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
- MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
- MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
- MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
- MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
-
- MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
- MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
-
- /* Configure clock provider for RGMII ref clock */
- MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0b0
- /* Configure clock consumer for RGMII ref clock */
- MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
-
- /* SJA1105Q switch reset */
- MX6QDL_PAD_DISP0_DAT11__GPIO5_IO05 0x10030
-
- /* phy3/rgmii_phy reset */
- MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x10030
- /* phy3/rgmii_phy int */
- MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x40010000
- >;
- };
-
- pinctrl_mdio0: mdio0grp {
- fsl,pins = <
- /* phy0/usbeth_phy reset */
- MX6QDL_PAD_DISP0_DAT17__GPIO5_IO11 0x10030
- /* phy0/usbeth_phy int */
- MX6QDL_PAD_DISP0_DAT18__GPIO5_IO12 0x100b1
-
- /* phy12/tja1102_phy0 reset */
- MX6QDL_PAD_DISP0_DAT15__GPIO5_IO09 0x10030
- /* phy12/tja1102_phy0 int */
- MX6QDL_PAD_DISP0_DAT14__GPIO5_IO08 0x100b1
- /* phy12/tja1102_phy0 enable. Set 100K pull-up */
- MX6QDL_PAD_DISP0_DAT16__GPIO5_IO10 0x1f030
- >;
- };
-
- pinctrl_ecspi2: ecspi2grp {
- fsl,pins = <
- MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
- MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
- MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
- MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x000b1
- >;
- };
-
-
-
- pinctrl_hog: hoggrp {
- fsl,pins = <
- /* SGTL5000 sys_mclk */
- MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0
- /* CAN1_SR + CAN2_SR GPIO outputs */
- MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13070
- MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x13070
- /* CAN1_TERM (not used on WD3) */
- MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0
-
- /* HW revision detect */
- /* REV_ID0 */
- MX6QDL_PAD_SD4_DAT0__GPIO2_IO08 0x1b0b0
- /* REV_ID1 */
- MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x1b0b0
- /* REV_ID2 */
- MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0
- /* REV_ID3 */
- MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x1b0b0
- /* REV_ID4 */
- MX6QDL_PAD_SD4_DAT4__GPIO2_IO12 0x1b0b0
-
- /* USB charging control */
- /* CHG Control */
- MX6QDL_PAD_NANDF_CS0__GPIO6_IO11 0x130b0
- /* RID0 */
- MX6QDL_PAD_NANDF_CS1__GPIO6_IO14 0x130b0
- /* RID1 */
- MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x130b0
- /* RID2 */
- MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0x130b0
-
- /* Power VSEL and TG */
- /* VSEL */
- MX6QDL_PAD_NANDF_ALE__GPIO6_IO08 0x1b0b0
- /* TG */
- MX6QDL_PAD_NANDF_CLE__GPIO6_IO07 0x1b0b0
-
- /* Display panel 0 GPIO */
- /* L/R */
- MX6QDL_PAD_CSI0_DAT10__GPIO5_IO28 0x1b0b0
- /* TS_nINT */
- MX6QDL_PAD_CSI0_DAT11__GPIO5_IO29 0x1b0b0
- /* EN */
- MX6QDL_PAD_CSI0_DAT12__GPIO5_IO30 0x1b0b0
- /* LVDS0_nINT */
- MX6QDL_PAD_CSI0_DAT14__GPIO6_IO00 0x1b0b0
- /* LVDS0_PD */
- MX6QDL_PAD_CSI0_DAT15__GPIO6_IO01 0x1b0b0
-
- /* Display panel 1 GPIO */
- /* L/R */
- MX6QDL_PAD_CSI0_MCLK__GPIO5_IO19 0x1b0b0
- /* TS_nINT */
- MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b0b0
- /* EN */
- MX6QDL_PAD_CSI0_PIXCLK__GPIO5_IO18 0x1b0b0
- /* LVDS1_nINT */
- MX6QDL_PAD_CSI0_DAT7__GPIO5_IO25 0x1b0b0
- /* LVDS1_PD */
- MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x1b0b0
-
- /* Camera */
- /* CAM_GPIO0 */
- MX6QDL_PAD_CSI0_DAT13__GPIO5_IO31 0x1b0b0
- /* CAM_nINT */
- MX6QDL_PAD_CSI0_DAT16__GPIO6_IO02 0x1b0b0
- /* CAM_GPIO1 */
- MX6QDL_PAD_CSI0_DAT17__GPIO6_IO03 0x1b0b0
- /* CAM_nPD */
- MX6QDL_PAD_CSI0_DAT18__GPIO6_IO04 0x1b0b0
- /* CAM_LOCK */
- MX6QDL_PAD_CSI0_DAT19__GPIO6_IO05 0x1b0b0
-
- /* USB ethernet reset (asix) */
- MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26 0x1b0b0
- >;
- };
-
- pinctrl_wifi_npd: wifinpd {
- fsl,pins = <
- /* WL_REG_ON */
- MX6QDL_PAD_NANDF_RB0__GPIO6_IO10 0x13069
- >;
- };
-
- pinctrl_usdhc2: usdhc2grp {
- fsl,pins = <
- MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9
- MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9
- MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
- MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
- MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
- MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9
- >;
- };
-
- pinctrl_audmux: audmuxgrp {
- fsl,pins = <
- MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
- MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
- MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
- >;
- };
-
- pinctrl_i2c2: i2c2grp {
- fsl,pins = <
- MX6QDL_PAD_EIM_EB2__I2C2_SCL 0x4001f8b1
- MX6QDL_PAD_EIM_D16__I2C2_SDA 0x4001f8b1
- >;
- };
-
- pinctrl_leds: ledsgrp {
- /* No leds */
- fsl,pins = <>;
- };
-
- pinctrl_ecspi3: ecspi3grp {
- fsl,pins = <
- MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1
- MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1
- MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1
- /* CS */
- MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x000b1
- /* CAN2_nINT */
- MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25 0x1b0b1
- >;
- };
- pinctrl_pwm1: pwm1grp {
- fsl,pins = <
- MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0
- >;
- };
+#include <arm/imx6qp-prtwd3.dts>
+#include "imx6qdl-prti6q-emmc.dtsi"
- pinctrl_pwm2: pwm2grp {
- fsl,pins = <
- MX6QDL_PAD_DISP0_DAT9__PWM2_OUT 0x1b0b0
- >;
- };
-};
diff --git a/arch/arm/dts/imx6qp-vicutp.dts b/arch/arm/dts/imx6qp-vicutp.dts
index 44cfe68867..1411071fb3 100644
--- a/arch/arm/dts/imx6qp-vicutp.dts
+++ b/arch/arm/dts/imx6qp-vicutp.dts
@@ -1,52 +1,5 @@
// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (c) 2014 Protonic Holland
- */
-
/dts-v1/;
-#include <arm/imx6qp.dtsi>
-#include "imx6qdl-vicut1.dtsi"
-
-/ {
- model = "Kverneland UT1P Board";
- compatible = "kvg,vicutp", "fsl,imx6qp";
-
- memory {
- reg = <0x10000000 0x80000000>;
- };
-};
-
-&fec {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_enet>;
- phy-mode = "rgmii";
- /* phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>; */
- status = "okay";
-};
-
-&iomuxc {
- pinctrl_enet: enetgrp {
- fsl,pins = <
- /* MX6QDL_ENET_PINGRP_RGMII_MD(0x1b030, 0x10030) */
- MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
- MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
- MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
- MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
- MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
- MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
- MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
- MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
- MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
- MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
- MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
- MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
- MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
- MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
- MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
- /* Phy reset */
- MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
- MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
- >;
- };
-};
+#include <arm/imx6qp-vicutp.dts>
+#include "imx6qdl-prti6q-nor.dtsi"
diff --git a/arch/arm/dts/imx6ul-prti6g.dts b/arch/arm/dts/imx6ul-prti6g.dts
index e65198bab2..f720a2518c 100644
--- a/arch/arm/dts/imx6ul-prti6g.dts
+++ b/arch/arm/dts/imx6ul-prti6g.dts
@@ -1,81 +1,64 @@
-/*
- * Copyright (C) 2016 Protonic Holland
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
+// SPDX-License-Identifier: GPL-2.0-or-later
/dts-v1/;
-#include "imx6ul-prti6g.dtsi"
+#include <arm/imx6ul-prti6g.dts>
/ {
- model = "Protonic PRTI6G Board";
- compatible = "prt,prti6g", "fsl,imx6ul";
-};
+ chosen {
+ stdout-path = &uart4;
-&pinctrl_hog {
- fsl,pins = <
- /* HW revision detect */
- MX6UL_PAD_ENET2_RX_DATA0__GPIO2_IO08 0x1b0b0 /* REV_ID0 */
- MX6UL_PAD_ENET2_RX_DATA1__GPIO2_IO09 0x1b0b0 /* REV_ID1 */
- MX6UL_PAD_ENET2_RX_EN__GPIO2_IO10 0x1b0b0 /* REV_ID2 */
- MX6UL_PAD_ENET2_TX_DATA0__GPIO2_IO11 0x1b0b0 /* REV_ID3 */
- MX6UL_PAD_ENET2_TX_EN__GPIO2_IO13 0x1b0b0 /* BOARD_ID0 */
- MX6UL_PAD_ENET2_TX_CLK__GPIO2_IO14 0x1b0b0 /* BOARD_ID1 */
- MX6UL_PAD_ENET2_RX_ER__GPIO2_IO15 0x1b0b0 /* BOARD_ID2 */
- MX6UL_PAD_ENET2_TX_DATA1__GPIO2_IO12 0x1b0b0 /* BOARD_ID3 */
+ environment at 0 {
+ compatible = "barebox,environment";
+ device-path = &usdhc2, "partname:barebox-environment";
+ };
+ };
- /* Safety controller IO */
- MX6UL_PAD_SNVS_TAMPER6__GPIO5_IO06 0x1b0b0 /* WAKE_SC */
- MX6UL_PAD_SNVS_TAMPER7__GPIO5_IO07 0x1b0b0 /* PROGRAM_SC */
- >;
-};
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
-&ecspi2 {
- status = "okay";
-};
+ /* Address will be determined by the bootloader */
+ ramoops {
+ compatible = "ramoops";
+ };
+ };
-&can2 {
- status = "okay";
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ /* Address will be determined by the bootloader */
+ ramoops {
+ compatible = "ramoops";
+ };
+ };
};
-&i2c2 {
- can_adc: ads1015 at 49 {
- compatible = "ti,ads1015";
- reg = <0x49>;
+&ecspi1 {
+ flash at 0 {
#address-cells = <1>;
- #size-cells = <0>;
+ #size-cells = <1>;
- channel at 4 {
- reg = <4>;
- ti,gain = <3>;
- ti,datarate = <3>;
+ partition at 0 {
+ label = "barebox";
+ reg = <0x0 0x100000>;
};
+ };
+};
- channel at 5 {
- reg = <5>;
- ti,gain = <3>;
- ti,datarate = <3>;
- };
+&usdhc2 {
+ #address-cells = <1>;
+ #size-cells = <1>;
- channel at 6 {
- reg = <6>;
- ti,gain = <3>;
- ti,datarate = <3>;
- };
+ partition at 40000 {
+ label = "barebox-environment";
+ reg = <0x40000 0x80000>;
+ };
- channel at 7 {
- reg = <7>;
- ti,gain = <3>;
- ti,datarate = <3>;
- };
+ partition at c0000 {
+ label = "state";
+ reg = <0xc0000 0x40000>;
};
};
diff --git a/arch/arm/dts/imx6ul-prti6g.dtsi b/arch/arm/dts/imx6ul-prti6g.dtsi
deleted file mode 100644
index c20bbd5bc2..0000000000
--- a/arch/arm/dts/imx6ul-prti6g.dtsi
+++ /dev/null
@@ -1,330 +0,0 @@
-/*
- * Copyright (C) 2016 Protonic Holland
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#include <arm/imx6ul.dtsi>
-#include <dt-bindings/gpio/gpio.h>
-
-/ {
- chosen {
- stdout-path = &uart1;
- environment at 0 {
- compatible = "barebox,environment";
- device-path = &flash, "partname:env";
- };
- };
-
- memory {
- reg = <0x80000000 0x10000000>;
- };
-
- regulators {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <0>;
-
- reg_3p2v: 3p2-regulator {
- compatible = "regulator-fixed";
- regulator-name = "regulator-3P2V";
- regulator-min-microvolt = <3200000>;
- regulator-max-microvolt = <3200000>;
- regulator-always-on;
- };
-
- reg_1p35v: 1p35-regulator {
- compatible = "regulator-fixed";
- regulator-name = "regulator-1P35V";
- regulator-min-microvolt = <1350000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- };
- };
-
- leds: leds {
- compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_leds>;
-
- debug {
- label = "debug0";
- gpios = <&gpio4 16 0>;
- linux,default-trigger = "heartbeat";
- };
- };
-};
-
-&usbotg1 {
- dr_mode = "host";
- status = "okay";
-};
-
-&uart1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart1>;
- status = "okay";
-};
-
-&usdhc1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc1>;
- cd-gpios = <&gpio4 12 GPIO_ACTIVE_LOW>;
- vmmc-supply = <®_3p2v>;
- wakeup-source;
- status = "okay";
-};
-
-&usdhc2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc2>;
- bus-width = <8>;
- non-removable;
- status = "okay";
-};
-
-&ecspi1 {
- fsl,spi-num-chipselects = <1>;
- cs-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ecspi1>;
- status = "okay";
-
- flash: w25q64fv at 0 {
- compatible = "winbond,w25q64", "jedec,spi-nor";
- spi-max-frequency = <20000000>;
- m25p,fast-read;
- reg = <0>;
-
- #address-cells = <1>;
- #size-cells = <1>;
-
- partition at 0 {
- label = "boot";
- reg = <0x0 0x60000>; /* 384 Kb */
- };
-
- partition at 60000 {
- label = "env";
- reg = <0x60000 0x10000>; /* 64 Kb */
- };
-
- partition at 70000 {
- label = "dtb";
- reg = <0x70000 0x10000>; /* 64 Kb */
- };
-
- partition at 80000 {
- label = "kernel";
- reg = <0x80000 0x780000>; /* 7680 Kb */
- };
- };
-};
-
-&ecspi2 {
- fsl,spi-num-chipselects = <1>;
- cs-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ecspi2>;
-};
-
-&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c1>;
- clock-frequency = <100000>;
- status = "okay";
-
- /* RFID chip */
-};
-
-&i2c2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c2>;
- clock-frequency = <100000>;
- status = "okay";
-
- rtc: pcf8563 at 51 {
- compatible = "nxp,pcf8563";
- reg = <0x51>;
- };
-
- tmp103: tmp103 at 70 {
- compatible = "ti,tmp103", "tmp103";
- reg = <0x70>;
- };
-};
-
-&fec1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_fec1 &pinctrl_ethphy0_rst>;
- phy-mode = "rmii";
- phy-handle = <ðphy0>;
- phy-reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <11>;
- status = "okay";
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- ethphy0: ethernet-phy at 0 {
- reg = <0>;
- };
- };
-};
-
-
-&can1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_flexcan1>;
- status = "okay";
-};
-
-&can2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_flexcan2>;
-};
-
-&iomuxc {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_hog>;
-
- prti6g {
- pinctrl_hog: hoggrp {
- fsl,pins = <
- /* HW revision detect */
- MX6UL_PAD_ENET2_RX_DATA0__GPIO2_IO08 0x1b0b0 /* REV_ID0 */
- MX6UL_PAD_ENET2_RX_DATA1__GPIO2_IO09 0x1b0b0 /* REV_ID1 */
- MX6UL_PAD_ENET2_RX_EN__GPIO2_IO10 0x1b0b0 /* REV_ID2 */
- MX6UL_PAD_ENET2_TX_DATA0__GPIO2_IO11 0x1b0b0 /* REV_ID3 */
- MX6UL_PAD_ENET2_TX_EN__GPIO2_IO13 0x1b0b0 /* BOARD_ID0 */
- MX6UL_PAD_ENET2_TX_CLK__GPIO2_IO14 0x1b0b0 /* BOARD_ID1 */
- MX6UL_PAD_ENET2_RX_ER__GPIO2_IO15 0x1b0b0 /* BOARD_ID2 */
- MX6UL_PAD_ENET2_TX_DATA1__GPIO2_IO12 0x1b0b0 /* BOARD_ID3 */
-
- /* CAN diagnostics (nSMBALERT) */
- MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x1b0b0
- >;
- };
-
- pinctrl_leds: ledsgrp {
- fsl,pins = <
- MX6UL_PAD_NAND_DQS__GPIO4_IO16 0x1b0b0
- >;
- };
-
- pinctrl_uart1: uart1grp {
- fsl,pins = <
- MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1
- MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1
- >;
- };
-
- pinctrl_usdhc1: usdhc1grp {
- fsl,pins = <
- MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x070b1
- MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x07099
- MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x070b1
- MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x070b1
- MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x070b1
- MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x070b1
- MX6UL_PAD_NAND_READY_B__GPIO4_IO12 0x170b0 /* SD1 CD */
- >;
- };
-
- pinctrl_usdhc2: usdhc2grp {
- fsl,pins = <
- MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170f9
- MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100f9
- MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170f9
- MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170f9
- MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170f9
- MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170f9
- MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x170f9
- MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x170f9
- MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x170f9
- MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x170f9
- MX6UL_PAD_NAND_ALE__USDHC2_RESET_B 0x170b0
- >;
- };
-
- pinctrl_ecspi1: ecspi1grp {
- fsl,pins = <
- MX6UL_PAD_CSI_DATA04__ECSPI1_SCLK 0x0b0b0
- MX6UL_PAD_CSI_DATA05__GPIO4_IO26 0x000b1
- MX6UL_PAD_CSI_DATA06__ECSPI1_MOSI 0x0b0b0
- MX6UL_PAD_CSI_DATA07__ECSPI1_MISO 0x0b0b0
- >;
- };
-
- pinctrl_ecspi2: ecspi2grp {
- fsl,pins = <
- MX6UL_PAD_CSI_DATA00__ECSPI2_SCLK 0x0b0b0
- MX6UL_PAD_CSI_DATA01__GPIO4_IO22 0x000b1
- MX6UL_PAD_CSI_DATA02__ECSPI2_MOSI 0x0b0b0
- MX6UL_PAD_CSI_DATA03__ECSPI2_MISO 0x0b0b0
- >;
- };
-
- pinctrl_i2c1: i2c1grp {
- fsl,pins = <
- MX6UL_PAD_CSI_MCLK__I2C1_SDA 0x4001b8b0
- MX6UL_PAD_CSI_PIXCLK__I2C1_SCL 0x4001b8b0
- >;
- };
-
- pinctrl_i2c2: i2c2grp {
- fsl,pins = <
- MX6UL_PAD_CSI_VSYNC__I2C2_SDA 0x4001b8b0
- MX6UL_PAD_CSI_HSYNC__I2C2_SCL 0x4001b8b0
- >;
- };
-
- pinctrl_fec1: fec1grp {
- fsl,pins = <
- MX6UL_PAD_GPIO1_IO07__ENET1_MDC 0x1b0b0
- MX6UL_PAD_GPIO1_IO06__ENET1_MDIO 0x100b0
- MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0
- MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0
- MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x100b0
- MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0
- MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b0b0
- MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0
- MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0
- MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4001b031
- >;
- };
-
- pinctrl_ethphy0_rst: ethphy-rstgrp-0 {
- fsl,pins = <
- MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x00880 /* PHY RESET */
- >;
- };
-
- pinctrl_flexcan1: flexcan1grp {
- fsl,pins = <
- MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX 0x0b0b0
- MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX 0x0b0b0
- MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03 0x0b0b0 /* SR */
- MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04 0x0b0b0 /* TERM */
- MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x0b0b0 /* nSMBALERT */
- >;
- };
-
- pinctrl_flexcan2: flexcan2grp {
- fsl,pins = <
- MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX 0x0b0b0
- MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX 0x0b0b0
- MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05 0x0b0b0 /* SR */
- >;
- };
- };
-};
--
2.29.2
More information about the barebox
mailing list