[PATCH 2/3] ddr: imx8m: clean up entry points
Lucas Stach
l.stach at pengutronix.de
Thu Nov 5 09:10:14 EST 2020
The DDRC address in the memory map and the TF-A parameter store address
is the same for all i.MX8M* SoCs. The only difference (for now) is in the
power up sequence. Add a enum for the DDRC type, so we can take different
code paths in imx8m_ddr_init() depending on the SoC.
Signed-off-by: Lucas Stach <l.stach at pengutronix.de>
---
arch/arm/boards/nxp-imx8mp-evk/lowlevel.c | 2 +-
drivers/ddr/imx8m/ddr_init.c | 82 ++++++++++-------------
include/soc/imx8m/ddr.h | 7 ++
3 files changed, 45 insertions(+), 46 deletions(-)
diff --git a/arch/arm/boards/nxp-imx8mp-evk/lowlevel.c b/arch/arm/boards/nxp-imx8mp-evk/lowlevel.c
index e4f994a1d1b8..3298ded5866d 100644
--- a/arch/arm/boards/nxp-imx8mp-evk/lowlevel.c
+++ b/arch/arm/boards/nxp-imx8mp-evk/lowlevel.c
@@ -118,7 +118,7 @@ static void start_atf(void)
power_init_board();
- imx8mm_ddr_init(&imx8mp_evk_dram_timing);
+ imx8mp_ddr_init(&imx8mp_evk_dram_timing);
imx8mp_get_boot_source(&src, &instance);
switch (src) {
diff --git a/drivers/ddr/imx8m/ddr_init.c b/drivers/ddr/imx8m/ddr_init.c
index bc64e7c17e1a..230fa7ef4266 100644
--- a/drivers/ddr/imx8m/ddr_init.c
+++ b/drivers/ddr/imx8m/ddr_init.c
@@ -13,8 +13,6 @@
#include <mach/imx8m-regs.h>
#include <mach/imx8m-ccm-regs.h>
-#define SRC_DDRC_RCR_ADDR MX8MQ_SRC_DDRC_RCR_ADDR
-
static void ddr_cfg_umctl2(struct dram_cfg_param *ddrc_cfg, int num)
{
int i = 0;
@@ -25,14 +23,37 @@ static void ddr_cfg_umctl2(struct dram_cfg_param *ddrc_cfg, int num)
}
}
-static int imx8m_ddr_init(unsigned long src_ddrc_rcr,
- struct dram_timing_info *dram_timing)
+/*
+ * We store the timing parameters here. the TF-A will pick these up.
+ * Note that the timing used we leave the driver with is a PLL bypass 25MHz
+ * mode. So if your board runs horribly slow you'll likely have to provide a
+ * TF-A binary.
+ */
+#define IMX8M_SAVED_DRAM_TIMING_BASE 0x180000
+
+static int imx8m_ddr_init(struct dram_timing_info *dram_timing,
+ enum ddrc_type type)
{
+ unsigned long src_ddrc_rcr = MX8M_SRC_DDRC_RCR_ADDR;
unsigned int tmp, initial_drate, target_freq;
int ret;
pr_debug("start DRAM init\n");
+ /* Step1: Follow the power up procedure */
+ switch (type) {
+ case DDRC_TYPE_MQ:
+ reg32_write(src_ddrc_rcr + 0x04, 0x8f00000f);
+ reg32_write(src_ddrc_rcr, 0x8f00000f);
+ reg32_write(src_ddrc_rcr + 0x04, 0x8f000000);
+ break;
+ case DDRC_TYPE_MM:
+ case DDRC_TYPE_MP:
+ reg32_write(src_ddrc_rcr, 0x8f00001f);
+ reg32_write(src_ddrc_rcr, 0x8f00000f);
+ break;
+ }
+
pr_debug("cfg clk\n");
/* disable iso */
@@ -44,7 +65,7 @@ static int imx8m_ddr_init(unsigned long src_ddrc_rcr,
ddrphy_init_set_dfi_clk(initial_drate);
/* D-aasert the presetn */
- reg32_write(SRC_DDRC_RCR_ADDR, 0x8F000006);
+ reg32_write(src_ddrc_rcr, 0x8F000006);
/* Step2: Program the dwc_ddr_umctl2 registers */
pr_debug("ddrc config start\n");
@@ -52,8 +73,8 @@ static int imx8m_ddr_init(unsigned long src_ddrc_rcr,
pr_debug("ddrc config done\n");
/* Step3: De-assert reset signal(core_ddrc_rstn & aresetn_n) */
- reg32_write(SRC_DDRC_RCR_ADDR, 0x8F000004);
- reg32_write(SRC_DDRC_RCR_ADDR, 0x8F000000);
+ reg32_write(src_ddrc_rcr, 0x8F000004);
+ reg32_write(src_ddrc_rcr, 0x8F000000);
/*
* Step4: Disable auto-refreshes, self-refresh, powerdown, and
@@ -162,52 +183,23 @@ static int imx8m_ddr_init(unsigned long src_ddrc_rcr,
reg32_write(DDRC_PCTRL_0(0), 0x00000001);
pr_debug(" ddrmix config done\n");
+ /* save the dram timing config into memory */
+ dram_config_save(dram_timing, IMX8M_SAVED_DRAM_TIMING_BASE);
+
return 0;
}
-/*
- * We store the timing parameters here. the TF-A will pick these up.
- * Note that the timing used we leave the driver with is a PLL bypass 25MHz
- * mode. So if your board runs horribly slow you'll likely have to provide a
- * TF-A binary.
- */
-#define IMX8M_SAVED_DRAM_TIMING_BASE 0x180000
-
int imx8mm_ddr_init(struct dram_timing_info *dram_timing)
{
- unsigned long src_ddrc_rcr = MX8M_SRC_DDRC_RCR_ADDR;
- int ret;
-
- /* Step1: Follow the power up procedure */
- reg32_write(src_ddrc_rcr, 0x8f00001f);
- reg32_write(src_ddrc_rcr, 0x8f00000f);
-
- ret = imx8m_ddr_init(src_ddrc_rcr, dram_timing);
- if (ret)
- return ret;
-
- /* save the dram timing config into memory */
- dram_config_save(dram_timing, IMX8M_SAVED_DRAM_TIMING_BASE);
-
- return 0;
+ return imx8m_ddr_init(dram_timing, DDRC_TYPE_MM);
}
int imx8mq_ddr_init(struct dram_timing_info *dram_timing)
{
- unsigned long src_ddrc_rcr = MX8MQ_SRC_DDRC_RCR_ADDR;
- int ret;
-
- /* Step1: Follow the power up procedure */
- reg32_write(src_ddrc_rcr + 0x04, 0x8f00000f);
- reg32_write(src_ddrc_rcr, 0x8f00000f);
- reg32_write(src_ddrc_rcr + 0x04, 0x8f000000);
-
- ret = imx8m_ddr_init(src_ddrc_rcr, dram_timing);
- if (ret)
- return ret;
-
- /* save the dram timing config into memory */
- dram_config_save(dram_timing, IMX8M_SAVED_DRAM_TIMING_BASE);
+ return imx8m_ddr_init(dram_timing, DDRC_TYPE_MQ);
+}
- return 0;
+int imx8mp_ddr_init(struct dram_timing_info *dram_timing)
+{
+ return imx8m_ddr_init(dram_timing, DDRC_TYPE_MP);
}
diff --git a/include/soc/imx8m/ddr.h b/include/soc/imx8m/ddr.h
index 5b2747ed1f7b..1408ffcfb557 100644
--- a/include/soc/imx8m/ddr.h
+++ b/include/soc/imx8m/ddr.h
@@ -363,8 +363,15 @@ struct dram_timing_info {
extern struct dram_timing_info dram_timing;
+enum ddrc_type {
+ DDRC_TYPE_MM,
+ DDRC_TYPE_MQ,
+ DDRC_TYPE_MP,
+};
+
int imx8mm_ddr_init(struct dram_timing_info *timing_info);
int imx8mq_ddr_init(struct dram_timing_info *timing_info);
+int imx8mp_ddr_init(struct dram_timing_info *timing_info);
int ddr_cfg_phy(struct dram_timing_info *timing_info);
void load_lpddr4_phy_pie(void);
void ddrphy_trained_csr_save(struct dram_cfg_param *param, unsigned int num);
--
2.20.1
More information about the barebox
mailing list