[PATCH v1] mci: add Marvell Dove SDHCI driver
Michael Grzeschik
m.grzeschik at pengutronix.de
Mon Apr 10 15:21:29 PDT 2017
From: Sebastian Hesselbarth <sebastian.hesselbarth at gmail.com>
This adds a driver for the SDHCI controller found on Marvell Dove SoCs.
Despite a missing pinctrl driver, corresponding MPP config has to be
set on a per board basis.
This driver was succesfully tested with Solidrun Dove Cubox.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth at gmail.com>
Signed-off-by: Michael Grzeschik <m.grzeschik at pengutronix.de>
---
RFC -> v1: - acknowledging the dma_int status bit to resume xfer
- added dma_sync_single_for_device where we handover data
- rate limited the multiwrite size with an max_req_size
and increased the timeout according to the data being
handled
---
arch/arm/configs/mvebu_defconfig | 1 +
drivers/mci/Kconfig | 7 +
drivers/mci/Makefile | 1 +
drivers/mci/dove-sdhci.c | 391 +++++++++++++++++++++++++++++++++++++++
drivers/mci/sdhci.h | 59 ++++++
5 files changed, 459 insertions(+)
create mode 100644 drivers/mci/dove-sdhci.c
diff --git a/arch/arm/configs/mvebu_defconfig b/arch/arm/configs/mvebu_defconfig
index dab3d7a45e..cfbccb5a14 100644
--- a/arch/arm/configs/mvebu_defconfig
+++ b/arch/arm/configs/mvebu_defconfig
@@ -112,6 +112,7 @@ CONFIG_USB_STORAGE=y
CONFIG_MCI=y
CONFIG_MCI_STARTUP=y
CONFIG_MCI_MMC_BOOT_PARTITIONS=y
+CONFIG_MCI_DOVE=y
CONFIG_LED=y
CONFIG_LED_GPIO=y
CONFIG_LED_GPIO_OF=y
diff --git a/drivers/mci/Kconfig b/drivers/mci/Kconfig
index 0f3504c735..954f957bc7 100644
--- a/drivers/mci/Kconfig
+++ b/drivers/mci/Kconfig
@@ -66,6 +66,13 @@ config MCI_BCM283X
bool "MCI support for BCM283X"
depends on ARCH_BCM283X
+config MCI_DOVE
+ bool "Marvell Dove SDHCI"
+ depends on ARCH_DOVE
+ help
+ Enable this entry to add support to read and write SD cards on a
+ Marvell Dove SoC based system.
+
config MCI_IMX
bool "i.MX"
depends on ARCH_IMX27 || ARCH_IMX31
diff --git a/drivers/mci/Makefile b/drivers/mci/Makefile
index 88ec456aa3..fe2c8adbac 100644
--- a/drivers/mci/Makefile
+++ b/drivers/mci/Makefile
@@ -1,6 +1,7 @@
obj-$(CONFIG_MCI) += mci-core.o
obj-$(CONFIG_MCI_ATMEL) += atmel_mci.o
obj-$(CONFIG_MCI_BCM283X) += mci-bcm2835.o
+obj-$(CONFIG_MCI_DOVE) += dove-sdhci.o
obj-$(CONFIG_MCI_IMX) += imx.o
obj-$(CONFIG_MCI_IMX_ESDHC) += imx-esdhc.o
obj-$(CONFIG_MCI_MXS) += mxs.o
diff --git a/drivers/mci/dove-sdhci.c b/drivers/mci/dove-sdhci.c
new file mode 100644
index 0000000000..82188960c6
--- /dev/null
+++ b/drivers/mci/dove-sdhci.c
@@ -0,0 +1,391 @@
+/*
+ * Marvell Dove SDHCI MCI driver
+ *
+ * Sebastian Hesselbarth <sebastian.hesselbarth at gmail.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <clock.h>
+#include <common.h>
+#include <init.h>
+#include <io.h>
+#include <dma.h>
+#include <malloc.h>
+#include <mci.h>
+#include <linux/err.h>
+
+#include "sdhci.h"
+
+struct dove_sdhci {
+ struct mci_host mci;
+ void __iomem *base;
+};
+
+#define priv_from_mci_host(h) \
+ container_of(h, struct dove_sdhci, mci);
+
+static inline void dove_sdhci_writel(struct dove_sdhci *p, int reg, u32 val)
+{
+ writel(val, p->base + reg);
+}
+
+static inline void dove_sdhci_writew(struct dove_sdhci *p, int reg, u16 val)
+{
+ writew(val, p->base + reg);
+}
+
+static inline void dove_sdhci_writeb(struct dove_sdhci *p, int reg, u8 val)
+{
+ writeb(val, p->base + reg);
+}
+
+static inline u32 dove_sdhci_readl(struct dove_sdhci *p, int reg)
+{
+ return readl(p->base + reg);
+}
+
+static inline u16 dove_sdhci_readw(struct dove_sdhci *p, int reg)
+{
+ return readw(p->base + reg);
+}
+
+static inline u8 dove_sdhci_readb(struct dove_sdhci *p, int reg)
+{
+ return readb(p->base + reg);
+}
+
+static int dove_sdhci_wait_for_done(struct dove_sdhci *host, u16 mask)
+{
+ u16 status;
+ u64 start;
+
+ start = get_time_ns();
+ while (1) {
+ status = dove_sdhci_readw(host, SDHCI_INT_NORMAL_STATUS);
+ if (status & SDHCI_INT_ERROR)
+ return -EPERM;
+ /* this special quirk is necessary, as the dma
+ * engine stops on dma boundary and will only
+ * restart after acknowledging it this way.
+ */
+ if (status & SDHCI_INT_DMA) {
+ u32 addr = dove_sdhci_readl(host, SDHCI_DMA_ADDRESS);
+ dove_sdhci_writel(host, SDHCI_DMA_ADDRESS, addr);
+ }
+ if (status & mask)
+ break;
+ if (is_timeout(start, 1000 * MSECOND)) {
+ dev_err(host->mci.hw_dev, "SDHCI timeout while waiting for done\n");
+ return -ETIMEDOUT;
+ }
+ }
+ return 0;
+}
+
+static int dove_sdhci_mci_send_cmd(struct mci_host *mci, struct mci_cmd *cmd,
+ struct mci_data *data)
+{
+ u16 val;
+ u64 start;
+ int ret;
+ unsigned int num_bytes = data->blocks * data->blocksize;
+ struct dove_sdhci *host = priv_from_mci_host(mci);
+
+ dove_sdhci_writel(host, SDHCI_INT_STATUS, ~0);
+
+ /* Do not wait for CMD_INHIBIT_DAT on stop commands */
+ if (cmd->cmdidx == MMC_CMD_STOP_TRANSMISSION)
+ val = SDHCI_CMD_INHIBIT_CMD;
+ else
+ val = SDHCI_CMD_INHIBIT_CMD | SDHCI_CMD_INHIBIT_DATA;
+
+ /* Wait for bus idle */
+ start = get_time_ns();
+ while (1) {
+ if (!(dove_sdhci_readw(host, SDHCI_PRESENT_STATE) & val))
+ break;
+ if (is_timeout(start, 10 * MSECOND)) {
+ dev_err(host->mci.hw_dev, "SDHCI timeout while waiting for idle\n");
+ return -ETIMEDOUT;
+ }
+ }
+
+ /* setup transfer data */
+ if (data) {
+ if (data->flags & MMC_DATA_READ)
+ dove_sdhci_writel(host, SDHCI_DMA_ADDRESS, (u32)data->dest);
+ else
+ dove_sdhci_writel(host, SDHCI_DMA_ADDRESS, (u32)data->src);
+ dove_sdhci_writew(host, SDHCI_BLOCK_SIZE, SDHCI_DMA_BOUNDARY_512K |
+ SDHCI_TRANSFER_BLOCK_SIZE(data->blocksize));
+ dove_sdhci_writew(host, SDHCI_BLOCK_COUNT, data->blocks);
+ dove_sdhci_writeb(host, SDHCI_TIMEOUT_CONTROL, 0xe);
+
+
+ if (data->flags & MMC_DATA_WRITE)
+ dma_sync_single_for_device((unsigned long)data->src,
+ num_bytes, DMA_TO_DEVICE);
+ else
+ dma_sync_single_for_device((unsigned long)data->dest,
+ num_bytes, DMA_FROM_DEVICE);
+ }
+
+ /* setup transfer mode */
+ val = 0;
+ if (data) {
+ val |= SDHCI_DMA_EN | SDHCI_BLOCK_COUNT_EN;
+ if (data->blocks > 1)
+ val |= SDHCI_MULTIPLE_BLOCKS;
+ if (data->flags & MMC_DATA_READ)
+ val |= SDHCI_DATA_TO_HOST;
+ }
+ dove_sdhci_writew(host, SDHCI_TRANSFER_MODE, val);
+
+ dove_sdhci_writel(host, SDHCI_ARGUMENT, cmd->cmdarg);
+
+ if (!(cmd->resp_type & MMC_RSP_PRESENT))
+ val = SDHCI_RESP_NONE;
+ else if (cmd->resp_type & MMC_RSP_136)
+ val = SDHCI_RESP_TYPE_136;
+ else if (cmd->resp_type & MMC_RSP_BUSY)
+ val = SDHCI_RESP_TYPE_48_BUSY;
+ else
+ val = SDHCI_RESP_TYPE_48;
+
+ if (cmd->resp_type & MMC_RSP_CRC)
+ val |= SDHCI_CMD_CRC_CHECK_EN;
+ if (cmd->resp_type & MMC_RSP_OPCODE)
+ val |= SDHCI_CMD_INDEX_CHECK_EN;
+ if (data)
+ val |= SDHCI_DATA_PRESENT;
+ val |= SDHCI_CMD_INDEX(cmd->cmdidx);
+
+ dove_sdhci_writew(host, SDHCI_COMMAND, val);
+
+ ret = dove_sdhci_wait_for_done(host, SDHCI_INT_CMD_COMPLETE);
+ if (ret) {
+ dev_err(host->mci.hw_dev, "error on command %d\n", cmd->cmdidx);
+ dev_err(host->mci.hw_dev, "state = %04x %04x, interrupt = %04x %04x\n",
+ dove_sdhci_readw(host, SDHCI_PRESENT_STATE),
+ dove_sdhci_readw(host, SDHCI_PRESENT_STATE1),
+ dove_sdhci_readw(host, SDHCI_INT_NORMAL_STATUS),
+ dove_sdhci_readw(host, SDHCI_INT_ERROR_STATUS));
+ goto cmd_error;
+ }
+
+ /* CRC is stripped so we need to do some shifting. */
+ if (cmd->resp_type & MMC_RSP_136) {
+ int i;
+ for (i = 0; i < 4; i++) {
+ cmd->response[i] = dove_sdhci_readl(host,
+ SDHCI_RESPONSE_0 + 4*(3-i)) << 8;
+ if (i != 3)
+ cmd->response[i] |= dove_sdhci_readb(host,
+ SDHCI_RESPONSE_0 + 4*(3-i) - 1);
+ }
+ } else
+ cmd->response[0] = dove_sdhci_readl(host, SDHCI_RESPONSE_0);
+
+ if (data->flags & MMC_DATA_WRITE)
+ dma_sync_single_for_cpu((unsigned long)data->src,
+ num_bytes, DMA_TO_DEVICE);
+ else
+ dma_sync_single_for_cpu((unsigned long)data->dest,
+ num_bytes, DMA_FROM_DEVICE);
+
+ if (data) {
+ ret = dove_sdhci_wait_for_done(host, SDHCI_INT_XFER_COMPLETE);
+ if (ret) {
+ dev_err(host->mci.hw_dev, "error while transfering data for command %d\n",
+ cmd->cmdidx);
+ dev_err(host->mci.hw_dev, "state = %04x %04x, interrupt = %04x %04x\n",
+ dove_sdhci_readw(host, SDHCI_PRESENT_STATE),
+ dove_sdhci_readw(host, SDHCI_PRESENT_STATE1),
+ dove_sdhci_readw(host, SDHCI_INT_NORMAL_STATUS),
+ dove_sdhci_readw(host, SDHCI_INT_ERROR_STATUS));
+ goto cmd_error;
+ }
+ }
+
+cmd_error:
+ dove_sdhci_writel(host, SDHCI_INT_STATUS, ~0);
+ return ret;
+}
+
+static u16 dove_sdhci_get_clock_divider(struct dove_sdhci *host, u32 reqclk)
+{
+ u16 div;
+
+ for (div = 1; div < SDHCI_SPEC_200_MAX_CLK_DIVIDER; div *= 2)
+ if ((host->mci.f_max / div) <= reqclk)
+ break;
+ div /= 2;
+
+ return div;
+}
+
+static void dove_sdhci_mci_set_ios(struct mci_host *mci, struct mci_ios *ios)
+{
+ u16 val;
+ u64 start;
+ struct dove_sdhci *host = priv_from_mci_host(mci);
+
+ debug("%s: clock = %u, bus-width = %d, timing = %02x\n", __func__, ios->clock, ios->bus_width, ios->timing);
+
+ /* disable on zero clock */
+ if (!ios->clock)
+ return;
+
+ /* enable bus power */
+ val = SDHCI_BUS_VOLTAGE_330;
+ dove_sdhci_writeb(host, SDHCI_POWER_CONTROL, val | SDHCI_BUS_POWER_EN);
+ udelay(400);
+
+ /* set bus width */
+ val = dove_sdhci_readb(host, SDHCI_HOST_CONTROL) &
+ ~(SDHCI_DATA_WIDTH_4BIT | SDHCI_DATA_WIDTH_8BIT);
+ switch (ios->bus_width) {
+ case MMC_BUS_WIDTH_8:
+ val |= SDHCI_DATA_WIDTH_8BIT;
+ break;
+ case MMC_BUS_WIDTH_4:
+ val |= SDHCI_DATA_WIDTH_4BIT;
+ break;
+ }
+
+ if (ios->clock > 26000000)
+ val |= SDHCI_HIGHSPEED_EN;
+ else
+ val &= ~SDHCI_HIGHSPEED_EN;
+
+ dove_sdhci_writeb(host, SDHCI_HOST_CONTROL, val);
+
+ /* set bus clock */
+ dove_sdhci_writew(host, SDHCI_CLOCK_CONTROL, 0);
+ val = dove_sdhci_get_clock_divider(host, ios->clock);
+ val = SDHCI_INTCLOCK_EN | SDHCI_FREQ_SEL(val);
+ dove_sdhci_writew(host, SDHCI_CLOCK_CONTROL, val);
+
+ /* wait for internal clock stable */
+ start = get_time_ns();
+ while (!(dove_sdhci_readw(host, SDHCI_CLOCK_CONTROL) &
+ SDHCI_INTCLOCK_STABLE)) {
+ if (is_timeout(start, 20 * MSECOND)) {
+ dev_err(host->mci.hw_dev, "SDHCI clock stable timeout\n");
+ return;
+ }
+ }
+
+ /* enable bus clock */
+ dove_sdhci_writew(host, SDHCI_CLOCK_CONTROL, val | SDHCI_SDCLOCK_EN);
+}
+
+static int dove_sdhci_mci_init(struct mci_host *mci, struct device_d *dev)
+{
+ u64 start;
+ struct dove_sdhci *host = priv_from_mci_host(mci);
+
+ /* reset sdhci controller */
+ dove_sdhci_writeb(host, SDHCI_SOFTWARE_RESET, SDHCI_RESET_ALL);
+
+ /* wait for reset completion */
+ start = get_time_ns();
+ while (1) {
+ if ((dove_sdhci_readb(host, SDHCI_SOFTWARE_RESET) &
+ SDHCI_RESET_ALL) == 0)
+ break;
+ if (is_timeout(start, 100 * MSECOND)) {
+ dev_err(dev, "SDHCI reset timeout\n");
+ return -ETIMEDOUT;
+ }
+ }
+
+ dove_sdhci_writel(host, SDHCI_INT_STATUS, ~0);
+ dove_sdhci_writel(host, SDHCI_INT_ENABLE, ~0);
+ dove_sdhci_writel(host, SDHCI_SIGNAL_ENABLE, ~0);
+
+ return 0;
+}
+
+static void dove_sdhci_set_mci_caps(struct dove_sdhci *host)
+{
+ u16 caps[2];
+
+ caps[0] = dove_sdhci_readw(host, SDHCI_CAPABILITIES);
+ caps[1] = dove_sdhci_readw(host, SDHCI_CAPABILITIES_1);
+
+ if (caps[1] & SDHCI_HOSTCAP_VOLTAGE_180)
+ host->mci.voltages |= MMC_VDD_165_195;
+ if (caps[1] & SDHCI_HOSTCAP_VOLTAGE_300)
+ host->mci.voltages |= MMC_VDD_29_30 | MMC_VDD_30_31;
+ if (caps[1] & SDHCI_HOSTCAP_VOLTAGE_330)
+ host->mci.voltages |= MMC_VDD_32_33 | MMC_VDD_33_34;
+
+ if (caps[1] & SDHCI_HOSTCAP_HIGHSPEED)
+ host->mci.host_caps |= (MMC_CAP_MMC_HIGHSPEED_52MHZ |
+ MMC_CAP_MMC_HIGHSPEED |
+ MMC_CAP_SD_HIGHSPEED);
+
+ /* parse board supported bus width capabilities */
+ mci_of_parse(&host->mci);
+
+ /* limit bus widths to controller capabilities */
+ if ((caps[1] & SDHCI_HOSTCAP_8BIT) == 0)
+ host->mci.host_caps &= ~MMC_CAP_8_BIT_DATA;
+}
+
+static int dove_sdhci_detect(struct device_d *dev)
+{
+ struct dove_sdhci *host = dev->priv;
+ return mci_detect_card(&host->mci);
+}
+
+static int dove_sdhci_probe(struct device_d *dev)
+{
+ struct dove_sdhci *host;
+ int ret;
+
+ host = xzalloc(sizeof(*host));
+ host->base = dev_request_mem_region(dev, 0);
+ host->mci.max_req_size = 0x8000;
+ host->mci.hw_dev = dev;
+ host->mci.send_cmd = dove_sdhci_mci_send_cmd;
+ host->mci.set_ios = dove_sdhci_mci_set_ios;
+ host->mci.init = dove_sdhci_mci_init;
+ host->mci.f_max = 50000000;
+ host->mci.f_min = host->mci.f_max / 256;
+ dev->priv = host;
+ dev->detect = dove_sdhci_detect;
+
+ dove_sdhci_set_mci_caps(host);
+
+ ret = mci_register(&host->mci);
+ if (ret)
+ free(host);
+ return ret;
+}
+
+static struct of_device_id dove_sdhci_dt_ids[] = {
+ { .compatible = "marvell,dove-sdhci", },
+ { }
+};
+
+static struct driver_d dove_sdhci_driver = {
+ .name = "dove-sdhci",
+ .probe = dove_sdhci_probe,
+ .of_compatible = DRV_OF_COMPAT(dove_sdhci_dt_ids),
+};
+device_platform_driver(dove_sdhci_driver);
diff --git a/drivers/mci/sdhci.h b/drivers/mci/sdhci.h
index 82a692e732..90595e6433 100644
--- a/drivers/mci/sdhci.h
+++ b/drivers/mci/sdhci.h
@@ -3,21 +3,80 @@
#define SDHCI_DMA_ADDRESS 0x00
#define SDHCI_BLOCK_SIZE__BLOCK_COUNT 0x04
+#define SDHCI_BLOCK_SIZE 0x04
+#define SDHCI_DMA_BOUNDARY_512K SDHCI_DMA_BOUNDARY(7)
+#define SDHCI_DMA_BOUNDARY_256K SDHCI_DMA_BOUNDARY(6)
+#define SDHCI_DMA_BOUNDARY_128K SDHCI_DMA_BOUNDARY(5)
+#define SDHCI_DMA_BOUNDARY_64K SDHCI_DMA_BOUNDARY(4)
+#define SDHCI_DMA_BOUNDARY_32K SDHCI_DMA_BOUNDARY(3)
+#define SDHCI_DMA_BOUNDARY_16K SDHCI_DMA_BOUNDARY(2)
+#define SDHCI_DMA_BOUNDARY_8K SDHCI_DMA_BOUNDARY(1)
+#define SDHCI_DMA_BOUNDARY_4K SDHCI_DMA_BOUNDARY(0)
+#define SDHCI_DMA_BOUNDARY(x) (((x) & 0x7) << 12)
+#define SDHCI_TRANSFER_BLOCK_SIZE(x) ((x) & 0xfff)
+#define SDHCI_BLOCK_COUNT 0x06
#define SDHCI_ARGUMENT 0x08
#define SDHCI_TRANSFER_MODE__COMMAND 0x0c
+#define SDHCI_TRANSFER_MODE 0x0c
+#define SDHCI_MULTIPLE_BLOCKS BIT(5)
+#define SDHCI_DATA_TO_HOST BIT(4)
+#define SDHCI_BLOCK_COUNT_EN BIT(1)
+#define SDHCI_DMA_EN BIT(0)
+#define SDHCI_COMMAND 0x0e
+#define SDHCI_CMD_INDEX(c) (((c) & 0x3f) << 8)
+#define SDHCI_DATA_PRESENT BIT(5)
+#define SDHCI_CMD_INDEX_CHECK_EN BIT(4)
+#define SDHCI_CMD_CRC_CHECK_EN BIT(3)
+#define SDHCI_RESP_TYPE_48_BUSY 3
+#define SDHCI_RESP_TYPE_48 2
+#define SDHCI_RESP_TYPE_136 1
+#define SDHCI_RESP_NONE 0
#define SDHCI_RESPONSE_0 0x10
#define SDHCI_RESPONSE_1 0x14
#define SDHCI_RESPONSE_2 0x18
#define SDHCI_RESPONSE_3 0x1c
#define SDHCI_BUFFER 0x20
#define SDHCI_PRESENT_STATE 0x24
+#define SDHCI_CMD_INHIBIT_DATA BIT(1)
+#define SDHCI_CMD_INHIBIT_CMD BIT(0)
+#define SDHCI_PRESENT_STATE1 0x26
#define SDHCI_HOST_CONTROL__POWER_CONTROL__BLOCK_GAP_CONTROL 0x28
+#define SDHCI_HOST_CONTROL 0x28
+#define SDHCI_DATA_WIDTH_8BIT BIT(5)
+#define SDHCI_HIGHSPEED_EN BIT(2)
+#define SDHCI_DATA_WIDTH_4BIT BIT(1)
+#define SDHCI_POWER_CONTROL 0x29
+#define SDHCI_BUS_VOLTAGE_330 SDHCI_BUS_VOLTAGE(7)
+#define SDHCI_BUS_VOLTAGE(v) ((v) << 1)
+#define SDHCI_BUS_POWER_EN BIT(0)
#define SDHCI_CLOCK_CONTROL__TIMEOUT_CONTROL__SOFTWARE_RESET 0x2c
+#define SDHCI_CLOCK_CONTROL 0x2c
+#define SDHCI_FREQ_SEL(x) (((x) & 0xff) << 8)
+#define SDHCI_SDCLOCK_EN BIT(2)
+#define SDHCI_INTCLOCK_STABLE BIT(1)
+#define SDHCI_INTCLOCK_EN BIT(0)
+#define SDHCI_TIMEOUT_CONTROL 0x2e
+#define SDHCI_SOFTWARE_RESET 0x2f
+#define SDHCI_RESET_ALL BIT(0)
#define SDHCI_INT_STATUS 0x30
+#define SDHCI_INT_NORMAL_STATUS 0x30
+#define SDHCI_INT_ERROR BIT(15)
+#define SDHCI_INT_DMA BIT(3)
+#define SDHCI_INT_XFER_COMPLETE BIT(1)
+#define SDHCI_INT_CMD_COMPLETE BIT(0)
+#define SDHCI_INT_ERROR_STATUS 0x32
#define SDHCI_INT_ENABLE 0x34
#define SDHCI_SIGNAL_ENABLE 0x38
#define SDHCI_ACMD12_ERR__HOST_CONTROL2 0x3C
#define SDHCI_CAPABILITIES 0x40
+#define SDHCI_CAPABILITIES_1 0x42
+#define SDHCI_HOSTCAP_VOLTAGE_180 BIT(10)
+#define SDHCI_HOSTCAP_VOLTAGE_300 BIT(9)
+#define SDHCI_HOSTCAP_VOLTAGE_330 BIT(8)
+#define SDHCI_HOSTCAP_HIGHSPEED BIT(5)
+#define SDHCI_HOSTCAP_8BIT BIT(2)
+
+#define SDHCI_SPEC_200_MAX_CLK_DIVIDER 256
#define SDHCI_MMC_BOOT 0xC4
#define COMMAND_CMD(x) ((x & 0x3f) << 24)
--
2.11.0
More information about the barebox
mailing list