[RFC V3 2/3] ddr_spd: add routune for printing SPD contents in human readable format
Antony Pavlov
antonynpavlov at gmail.com
Mon Jun 29 09:15:19 PDT 2015
On Mon, 29 Jun 2015 17:26:56 +0300
Alexander Smirnov <alllecs at yandex.ru> wrote:
> Signed-off-by: Alexander Smirnov <alllecs at yandex.ru>
> ---
> common/ddr_spd.c | 239 ++++++++++++++++++++++++++++++++++++++++++++++++++++++
> include/ddr_spd.h | 1 +
> 2 files changed, 240 insertions(+)
>
> diff --git a/common/ddr_spd.c b/common/ddr_spd.c
> index ea0b529..380ea18 100644
> --- a/common/ddr_spd.c
> +++ b/common/ddr_spd.c
> @@ -61,3 +61,242 @@ uint32_t ddr3_spd_checksum_pass(const struct ddr3_spd_eeprom_s *spd)
>
> return 0;
> }
> +
> +static char *heights[] = {
> + "<25.4",
> + "25.4",
> + "25.4 - 30.0",
> + "30.0",
> + "30.5",
> + "> 30.5"
> +};
> +
> +static char *sdram_voltage_interface_level[] = {
> + "TTL (5V tolerant)",
> + "LVTTL (not 5V tolerant)",
> + "HSTL 1.5V",
> + "SSTL 3.3V",
> + "SSTL 2.5V",
> + "SSTL 1.8V"
> +};
> +
> +static char *ddr2_module_types[] = {
> + "RDIMM (133.35 mm)",
> + "UDIMM (133.25 mm)",
> + "SO-DIMM (67.6 mm)",
> + "Micro-DIMM (45.5 mm)",
> + "Mini-RDIMM (82.0 mm)",
> + "Mini-UDIMM (82.0 mm)"
> +};
> +
> +static char *refresh[] = {
> + "15.625",
> + "3.9",
> + "7.8",
> + "31.3",
> + "62.5",
> + "125"
> +};
> +
> +static char *type_list[] = {
> + "Reserved",
> + "FPM DRAM",
> + "EDO",
> + "Pipelined Nibble",
> + "SDR SDRAM",
> + "Multiplexed ROM",
> + "DDR SGRAM",
> + "DDR SDRAM",
> + "DDR2 SDRAM",
> + "FB-DIMM",
> + "FB-DIMM Probe",
> + "DDR3 SDRAM"
> +};
> +
> +static int funct(uint8_t addr)
> +{
> + int t;
> +
> + t = ((addr >> 4) * 10 + (addr & 0xf));
> +
> + return t;
> +}
> +
> +static int des(uint8_t byte)
> +{
> + int k;
> +
> + k = (byte & 0x3) * 10 / 4;
> +
> + return k;
> +}
> +
> +static int integ(uint8_t byte)
> +{
> + int k;
> +
> + k = (byte >> 2);
> +
> + return k;
> +}
> +
> +static int ddr2_sdram_ctime(uint8_t byte)
> +{
> + int ctime;
> +
> + ctime = (byte >> 4) * 100;
> + if ((byte & 0xf) <= 9)
> + ctime += (byte & 0xf) * 10;
> + else if ((byte & 0xf) == 10)
> + ctime += 25;
> + else if ((byte & 0xf) == 11)
> + ctime += 33;
> + else if ((byte & 0xf) == 12)
> + ctime += 66;
> + else if ((byte & 0xf) == 13)
> + ctime += 75;
> +
> + return ctime;
> +}
> +
> +void ddr_spd_print(uint8_t *record)
> +{
> + int highestCAS = 0;
> + int cas[256];
> + int i, i_i, k, x, y;
> + int ddrclk, tbits, pcclk;
> + int trcd, trp, tras;
> + int ctime;
> + uint8_t parity;
> + char *ref;
> + struct ddr2_spd_eeprom_s *s = (struct ddr2_spd_eeprom_s *)record;
> +
> + ctime = ddr2_sdram_ctime(s->clk_cycle);
> + ddrclk = 2 * (1000 / ctime) * 100;
> + tbits = ((s->res_7) << 8) + (s->dataw);
> + if (((s->config) & 0x03) == 1)
> + tbits = tbits - 8;
> +
> + pcclk = ddrclk * tbits / 8;
> + pcclk = pcclk - (pcclk % 100);
> + i_i = ((s->nrow_addr) & 0x0f) + ((s->ncol_addr) & 0x0f) - 17;
> + k = (((s->mod_ranks) & 0x7) + 1) * (s->nbanks);
> + trcd = (((s->trcd) >> 2) + (((s->trcd) & 3) * 0.25)) / ctime * 100;
> + trp = (((s->trp) >> 2) + (((s->trp) & 3) * 0.25)) / ctime * 100;
> + tras = (s->tras) * 100 / ctime ;
> + x = (int)(ctime / 100);
> + y = (ctime - (int)((ctime / 100) * 100)) / 10;
> +
> + for (i_i = 2; i_i < 7; i_i++) {
> + if ((s->cas_lat) & (1 << i_i)) {
> + highestCAS = i_i;
> + cas[highestCAS]++;
> + }
> + }
> + printf("---=== SPD EEPROM Information ===---\n");
> + printf("%-50s OK (0x%0X)\n", "EEPROM Checksum of bytes 0-62", s->cksum);
> + printf("%-50s %d\n", "# of bytes written to SDRAM EEPROM", s->info_size);
> + printf("%-50s %d\n", "Total number of bytes in EEPROM", 1 << (s->chip_size));
> +
> + if ((s->mem_type) < 11)
> + printf("%-50s %s\n", "Fundamental Memory type", type_list[(s->mem_type)]);
> + else
> + printf("%-50s (%02x)\n", "Warning: unknown memory type", s->mem_type);
> +
> + printf("%-50s %x.%x\n", "SPD Revision", (s->spd_rev) >> 4, (s->spd_rev) & 0x0f);
> +
> + printf("\n---=== Memory Characteristics ===---\n");
> + printf("%-50s %d MHz (PC2-%d)\n", "Maximum module speed", ddrclk, pcclk);
> + if (i_i > 0 && i_i <= 12 && k > 0)
> + printf("%-50s %d MB\n", "Size", ((1 << i_i) * k));
extra brackets here.
> + else
> + printf("%-50s INVALID: %02x %02x %02x %02x\n", "Size", s->nrow_addr, s->ncol_addr, s->mod_ranks, s->nbanks);
> +
> + printf("%-50s %d x %d x %d x %d\n", "Banks x Rows x Columns x Bits", s->nbanks, s->nrow_addr, s->ncol_addr, s->dataw);
> + printf("%-50s %d\n", "Ranks", ((s->mod_ranks) & 0x7) + 1);
and here
> + printf("%-50s %d bits\n", "SDRAM Device Width", (s->primw));
and here
> + if (((s->mod_ranks) >> 5) < 7)
Please use ARRAY_SIZE(heights) instead of 7.
> + printf("%-50s %s mm\n", "Module Height", heights[((s->mod_ranks) >> 5)]);
> + else
> + printf("Error height\n");
> +
> + printf("%-50s %s\n", "Module Type", ddr2_module_types[fls(s->dimm_type) - 1]);
> + printf("%-50s ", "DRAM Package ");
> + if (((s->mod_ranks) & 0x10) == 1)
> + printf("Stack\n");
> + else
> + printf("Planar\n");
> + if ((s->voltage) < 7)
> + printf("%-50s %s\n", "Voltage Interface Level", sdram_voltage_interface_level[s->voltage]);
> + else
> + printf("Error Voltage Interface Level\n");
> +
> + printf("%-50s ", "Module Configuration Type ");
> +
> + parity = (s->config) & 0x07;
> + if (parity == 0)
> + printf("No Parity\n");
> +
> + if ((parity & 0x03) == 0x01)
> + printf("Data Parity\n");
> + if (parity & 0x02)
> + printf("Data ECC\n");
> +
> + if (parity & 0x04)
> + printf("Address/Command Parity\n");
> +
> + if (((s->refresh) >> 7) == 1)
> + ref = "- Self Refresh";
> + else
> + ref = " ";
> +
> + printf("%-50s Reduced (%s us) %s\n", "Refresh Rate", refresh[(s->refresh) & 0x7f], ref);
> + printf("%-50s %d, %d\n", "Supported Burst Lengths", (s->burstl) & 4, (s->burstl) & 8);
> +
> + printf("%-50s %dT\n", "Supported CAS Latencies (tCL)", highestCAS);
> + printf("%-50s %d-%d-%d-%d as DDR2-%d\n", "tCL-tRCD-tRP-tRAS", highestCAS, trcd, trp, tras, ddrclk);
> + printf("%-50s %d.%d ns at CAS %d\n", "Minimum Cycle Time", x, y, highestCAS);
> + printf("%-50s 0.%d%d ns at CAS %d\n", "Maximum Access Time", ((s->clk_access) >> 4), ((s->clk_access) & 0xf), highestCAS);
> + printf("%-50s %d ns\n", "Maximum Cycle Time (tCK max)", ((s->tckmax) >> 4) + ((s->tckmax) & 0x0f));
> +printf("\n---=== Timing Parameters ===---\n");
wrong formatting here.
> + printf("%-50s 0.%d ns\n", "Address/Command Setup Time Before Clock (tIS)", (funct(s->ca_setup)));
> + printf("%-50s 0.%d ns\n", "Address/Command Hold Time After Clock (tIH)", (funct(s->ca_hold)));
> + printf("%-50s 0.%d%d ns\n", "Data Input Setup Time Before Strobe (tDS)", ((s->data_setup) >> 4), ((s->data_setup) & 0xf));
> + printf("%-50s 0.%d%d ns\n", "Data Input Hold Time After Strobe (tDH)", ((s->data_hold) >> 4), ((s->data_hold) & 0xf));
> +
> + printf("%-50s %d.%d ns\n", "Minimum Row Precharge Delay (tRP)", integ(s->trp), des(s->trp));
> + printf("%-50s %d.%d ns\n", "Minimum Row Active to Row Active Delay (tRRD)", integ(s->trrd), des(s->trrd));
> + printf("%-50s %d.%d ns\n", "Minimum RAS# to CAS# Delay (tRCD)", integ(s->trcd), des(s->trcd));
> + printf("%-50s %d ns\n", "Minimum RAS# Pulse Width (tRAS)", (((s->tras) & 0xfc) + ((s->tras) & 0x3)));
> + printf("%-50s %d.%d ns\n", "Write Recovery Time (tWR)", integ(s->twr), des(s->twr));
> + printf("%-50s %d.%d ns\n", "Minimum Write to Read CMD Delay (tWTR)", integ(s->twtr), des(s->twtr));
> + printf("%-50s %d.%d ns\n", "Minimum Read to Pre-charge CMD Delay (tRTP)", integ(s->trtp), des(s->trtp));
> + printf("%-50s %d ns\n", "Minimum Active to Auto-refresh Delay (tRC)", s->trc);
> + printf("%-50s %d ns\n", "Minimum Recovery Delay (tRFC)", s->trfc);
> + printf("%-50s 0.%d ns\n", "Maximum DQS to DQ Skew (tDQSQ)", s->tdqsq);
> + printf("%-50s 0.%d ns\n", "Maximum Read Data Hold Skew (tQHS)", s->tqhs);
> +
> + printf("\n---=== Manufacturing Information ===---\n");
> +
> + printf("%-50s", "Manufacturer JEDEC ID");
> + for (i = 64; i < 72; i++)
> + printf(" %02x", record[i]);
> +
> + printf("\n");
> + if (s->mloc)
> + printf("%-50s 0x%02x\n", "Manufacturing Location Code", s->mloc);
> +
> + printf("%-50s ", "Part Number");
> + for (i = 73; i < 91; i++) {
> + if (record[i] >= 32 && record[i] < 127)
> + printf("%c", record[i]);
> + else
> + printf("%d", record[i]);
> + }
> + printf("\n");
> + printf("%-50s 20%d-W%d\n", "Manufacturing Date", record[93], record[94]);
> + printf("%-50s 0x", "Assembly Serial Number");
> + for (i = 95; i < 99; i++)
> + printf("%02X", record[i]);
> +}
> diff --git a/include/ddr_spd.h b/include/ddr_spd.h
> index fc03bac..01fe73c 100644
> --- a/include/ddr_spd.h
> +++ b/include/ddr_spd.h
> @@ -228,6 +228,7 @@ struct ddr3_spd_eeprom_s {
> uint8_t cust[80]; /* 176-255 Open for Customer Use */
> };
>
> +extern void ddr_spd_print(uint8_t *record);
> extern uint32_t ddr3_spd_checksum_pass(const struct ddr3_spd_eeprom_s *spd);
> extern uint32_t ddr2_spd_checksum_pass(const struct ddr2_spd_eeprom_s *spd);
>
> --
> 2.1.4
>
>
> _______________________________________________
> barebox mailing list
> barebox at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/barebox
--
--
Best regards,
Antony Pavlov
More information about the barebox
mailing list