[PATCH 2/6] raspberry-pi: add leds support

[Jean-Christophe PLAGNIOL-VILLARD]

> On Jan 13, 2015, at 3:58 PM, Antony Pavlov <antonynpavlov at gmail.com> wrote:
> 
> On Tue, 13 Jan 2015 07:26:12 +0100
> Jean-Christophe PLAGNIOL-VILLARD <plagnioj at jcrosoft.com> wrote:
> 
> I have planned to switch raspberry pi to device tree support as Linux does.

but as I do not want to build multi binary switch (leds & co) those to DT make no sense except if we can
chose the DT at runtime

> 
> IMHO POWER LED is not GPIO controlable, please see these schematics

yes it is does, I have a B+ and it’s controllable

Best Regards,
J.
> 
>   http://www.raspberrypi.org/wp-content/uploads/2012/04/Raspberry-Pi-Schematics-R1.0.pdf
>   http://www.raspberrypi.org/documentation/hardware/raspberrypi/schematics/Raspberry-Pi-B-Plus-V1.2-Schematics.pdf
> 
> 
>> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj at jcrosoft.com>
>> ---
>> arch/arm/boards/raspberry-pi/rpi.c | 55 ++++++++++++++++++++++++++++++++++++++
>> 1 file changed, 55 insertions(+)
>> 
>> diff --git a/arch/arm/boards/raspberry-pi/rpi.c b/arch/arm/boards/raspberry-pi/rpi.c
>> index ae1e92a..7d866cc 100644
>> --- a/arch/arm/boards/raspberry-pi/rpi.c
>> +++ b/arch/arm/boards/raspberry-pi/rpi.c
>> @@ -21,6 +21,8 @@
>> #include <linux/clkdev.h>
>> #include <envfs.h>
>> #include <malloc.h>
>> +#include <gpio.h>
>> +#include <led.h>
>> #include <asm/armlinux.h>
>> #include <generated/mach-types.h>
>> 
>> @@ -87,6 +89,49 @@ static int rpi_register_clkdev(u32 clock_id, const char *name)
>> }
>> 
>> 
>> +static struct gpio_led leds[] = {
>> +	{
>> +		.gpio	= -EINVAL,
>> +		.led	= {
>> +			.name = "ACT",
>> +		},
>> +	}, {
>> +		.gpio	= -EINVAL,
>> +		.led	= {
>> +			.name = "PWR",
>> +		},
>> +	},
>> +};
>> +
>> +static void rpi_add_led(void)
>> +{
>> +	int i;
>> +	struct gpio_led *l;
>> +
>> +	for (i = 0; i < ARRAY_SIZE(leds); i++) {
>> +		l = &leds[i];
>> +
>> +		if (gpio_is_valid(l->gpio))
>> +			led_gpio_register(l);
>> +	}
>> +
>> +	l = &leds[0];
>> +	if (gpio_is_valid(l->gpio))
>> +		led_set_trigger(LED_TRIGGER_HEARTBEAT, &l->led);
>> +}
>> +
>> +static void rpi_b_plus_init(void)
>> +{
>> +	leds[0].gpio = 47;
>> +	leds[1].gpio = 35;
>> +}
>> +
>> +static void rpi_b_init(void)
>> +{
>> +	leds[0].gpio = 16;
>> +	leds[0].active_low = 1;
>> +}
>> +
>> #define RPI_MODEL(_id, _name, _init)	\
>> 	[_id] = {				\
>> 		.name			= _name,\
>> @@ -160,6 +205,15 @@ unknown_rev:
>> 	barebox_set_model("RaspberryPi (BCM2835/ARM1176JZF-S)");
>> }
>> 
>> +static void rpi_model_init(void)
>> +{
>> +	rpi_set_usbethaddr();
>> +	if (models[rpi_board_rev].init) {
>> +		models[rpi_board_rev].init();
>> +		rpi_add_led();
>> +	}
>> +}
>> +
>> static int rpi_mem_init(void)
>> {
>> 	u32 size = 0;
>> @@ -220,6 +274,7 @@ static int rpi_env_init(void)
>> 
>> static int rpi_devices_init(void)
>> {
>> +	rpi_model_init();
>> 	bcm2835_register_mci();
>> 	bcm2835_register_fb();
>> 	armlinux_set_architecture(MACH_TYPE_BCM2708);
>> -- 
>> 2.1.3
>> 
>> 
>> _______________________________________________
>> barebox mailing list
>> barebox at lists.infradead.org
>> http://lists.infradead.org/mailman/listinfo/barebox
> 
> 
> -- 
> -- 
> Best regards,
>   Antony Pavlov