[PATCH 3/5] ARM: omap: move GPMC calls under config define

Marc Kleine-Budde mkl at pengutronix.de
Mon Apr 20 02:09:57 PDT 2015


On 04/20/2015 10:55 AM, Lucas Stach wrote:
> Fixes build failures on a few boards if CONFIG_OMAP_GPMC
> is not set.
> 
> Signed-off-by: Lucas Stach <l.stach at pengutronix.de>
> ---
>  arch/arm/boards/beagle/board.c                   |  4 +++-
>  arch/arm/boards/phytec-phycard-omap3/pca-a-l1.c  | 11 +++++++----
>  arch/arm/boards/phytec-phycard-omap4/pca-a-xl2.c | 10 +++++++---
>  arch/arm/boards/phytec-phycore-omap4460/board.c  |  9 +++++++--
>  4 files changed, 24 insertions(+), 10 deletions(-)
> 
> diff --git a/arch/arm/boards/beagle/board.c b/arch/arm/boards/beagle/board.c
> index 775621069c27..c7fd5a30542e 100644
> --- a/arch/arm/boards/beagle/board.c
> +++ b/arch/arm/boards/beagle/board.c
> @@ -74,11 +74,13 @@ static struct i2c_board_info i2c_devices[] = {
>  	},
>  };
>  
> +#ifdef CONFIG_OMAP_GPMC
>  static struct gpmc_nand_platform_data nand_plat = {
>  	.device_width = 16,
>  	.ecc_mode = OMAP_ECC_HAMMING_CODE_HW_ROMCODE,
>  	.nand_cfg = &omap3_nand_cfg,
>  };
> +#endif
>  
>  static int beagle_mem_init(void)
>  {
> @@ -100,8 +102,8 @@ static int beagle_devices_init(void)
>  #ifdef CONFIG_OMAP_GPMC
>  	/* WP is made high and WAIT1 active Low */
>  	gpmc_generic_init(0x10);
> -#endif
>  	omap_add_gpmc_nand_device(&nand_plat);
> +#endif
>  
>  	omap3_add_mmc1(NULL);
>  
> diff --git a/arch/arm/boards/phytec-phycard-omap3/pca-a-l1.c b/arch/arm/boards/phytec-phycard-omap3/pca-a-l1.c
> index 1c2e7f7429a2..0f3b79752d26 100644
> --- a/arch/arm/boards/phytec-phycard-omap3/pca-a-l1.c
> +++ b/arch/arm/boards/phytec-phycard-omap3/pca-a-l1.c
> @@ -77,7 +77,7 @@ static int pcaal1_init_console(void)
>  }
>  console_initcall(pcaal1_init_console);
>  
> -#ifdef CONFIG_DRIVER_NET_SMC911X
> +#if defined(CONFIG_DRIVER_NET_SMC911X) && defined(CONFIG_OMAP_GPMC)
>  /** GPMC timing for our SMSC9221 device */
>  static struct gpmc_config smsc_cfg = {
>  	.cfg = {
> @@ -132,23 +132,26 @@ struct omap_hsmmc_platform_data pcaal1_hsmmc_plat = {
>  	.f_max = 26000000,
>  };
>  
> +#ifdef CONFIG_OMAP_GPMC
>  static struct gpmc_nand_platform_data nand_plat = {
>  	.device_width = 16,
>  	.ecc_mode = OMAP_ECC_BCH8_CODE_HW,
>  	.nand_cfg = &omap3_nand_cfg,
>  };
> +#endif
>  
>  static int pcaal1_init_devices(void)
>  {
> +#ifdef CONFIG_OMAP_GPMC
>  	omap_add_gpmc_nand_device(&nand_plat);
> -
> -	omap3_add_mmc1(&pcaal1_hsmmc_plat);
> -
>  #ifdef CONFIG_DRIVER_NET_SMC911X
>  	pcaal1_setup_net_chip();
>  	add_generic_device("smc911x", DEVICE_ID_DYNAMIC, NULL, SMC911X_BASE, SZ_4K,
>  			   IORESOURCE_MEM, NULL);
>  #endif
> +#endif
> +
> +	omap3_add_mmc1(&pcaal1_hsmmc_plat);
>  
>  	armlinux_set_architecture(MACH_TYPE_PCAAL1);
>  
> diff --git a/arch/arm/boards/phytec-phycard-omap4/pca-a-xl2.c b/arch/arm/boards/phytec-phycard-omap4/pca-a-xl2.c
> index 78890ba5a978..e2ce6060e20a 100644
> --- a/arch/arm/boards/phytec-phycard-omap4/pca-a-xl2.c
> +++ b/arch/arm/boards/phytec-phycard-omap4/pca-a-xl2.c
> @@ -60,6 +60,7 @@ static int pcaaxl2_mem_init(void)
>  }
>  mem_initcall(pcaaxl2_mem_init);
>  
> +#ifdef CONFIG_OMAP_GPMC
>  static struct gpmc_config net_cfg = {
>  	.cfg = {
>  		0x00001000, /* CONF1 */
> @@ -80,6 +81,7 @@ static void pcaaxl2_network_init(void)
>  	add_ks8851_device(DEVICE_ID_DYNAMIC, net_cfg.base, net_cfg.base + 2,
>  				IORESOURCE_MEM_16BIT, NULL);
>  }
> +#endif
>  
>  static struct i2c_board_info i2c_devices[] = {
>  	{
> @@ -96,11 +98,13 @@ static struct omap_hsmmc_platform_data mmc_device = {
>  #define OMAP4_MMC1_PBIASLITE_PWRDNZ		(1<<22)
>  #define OMAP4_MMC1_PWRDNZ			(1<<26)
>  
> +#ifdef CONFIG_OMAP_GPMC
>  static struct gpmc_nand_platform_data nand_plat = {
>  	.device_width = 16,
>  	.ecc_mode = OMAP_ECC_BCH8_CODE_HW,
>  	.nand_cfg = &omap4_nand_cfg,
>  };
> +#endif
>  
>  static int pcaaxl2_devices_init(void)
>  {
> @@ -116,11 +120,11 @@ static int pcaaxl2_devices_init(void)
>  
>  	omap44xx_add_mmc1(&mmc_device);
>  
> +#ifdef CONFIG_OMAP_GPMC
>  	gpmc_generic_init(0x10);
> -
> -	pcaaxl2_network_init();
> -
>  	omap_add_gpmc_nand_device(&nand_plat);
> +	pcaaxl2_network_init();
> +#endif
>  
>  #ifdef CONFIG_PARTITION
>  	devfs_add_partition("nand0", 0x00000, SZ_128K,
> diff --git a/arch/arm/boards/phytec-phycore-omap4460/board.c b/arch/arm/boards/phytec-phycore-omap4460/board.c
> index 6495a6f6ab0a..1cee75ddb946 100644
> --- a/arch/arm/boards/phytec-phycore-omap4460/board.c
> +++ b/arch/arm/boards/phytec-phycore-omap4460/board.c
> @@ -64,6 +64,7 @@ static int pcm049_mem_init(void)
>  }
>  mem_initcall(pcm049_mem_init);
>  
> +#ifdef CONFIG_OMAP_GPMC
>  static struct gpmc_config net_cfg = {
>  	.cfg = {
>  		0xc1001000,	/* CONF1 */
> @@ -84,6 +85,7 @@ static void pcm049_network_init(void)
>  	add_generic_device("smc911x", DEVICE_ID_DYNAMIC, NULL, 0x2C000000, 0x4000,
>  			   IORESOURCE_MEM, NULL);
>  }
> +#endif
>  
>  static struct i2c_board_info i2c_devices[] = {
>  	{
> @@ -91,11 +93,13 @@ static struct i2c_board_info i2c_devices[] = {
>  	},
>  };
>  
> +#ifdef CONFIG_OMAP_GPMC
>  static struct gpmc_nand_platform_data nand_plat = {
>  	.wait_mon_pin = 1,
>  	.ecc_mode = OMAP_ECC_BCH8_CODE_HW,
>  	.nand_cfg = &omap4_nand_cfg,
>  };
> +#endif

You can use __maybe_unused to avoid the ifdef.

Marc

-- 
Pengutronix e.K.                  | Marc Kleine-Budde           |
Industrial Linux Solutions        | Phone: +49-231-2826-924     |
Vertretung West/Dortmund          | Fax:   +49-5121-206917-5555 |
Amtsgericht Hildesheim, HRA 2686  | http://www.pengutronix.de   |

-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 801 bytes
Desc: OpenPGP digital signature
URL: <http://lists.infradead.org/pipermail/barebox/attachments/20150420/6399615c/attachment-0001.sig>


More information about the barebox mailing list