[PATCH 4/5] ARM: mvebu: Allow multiple SoCs

[Sascha Hauer]

On Mon, Sep 15, 2014 at 11:12:03PM +0200, Sebastian Hesselbarth wrote:
> On 09/15/2014 11:13 AM, Sascha Hauer wrote:
> > On Mon, Sep 15, 2014 at 10:00:40AM +0200, Sebastian Hesselbarth wrote:
> >> On 09/15/2014 09:41 AM, Sascha Hauer wrote:
> >>> Now that the correct SoC specific memory fixup function is called
> >>> we can allow to select multiple SoCs in Kconfig.
> >>>
> >>> Signed-off-by: Sascha Hauer <s.hauer at pengutronix.de>
> >>
> >> Sascha,
> >>
> >> thanks for the patches, I'll give them a try later. FWIW, this
> >> patch allows to build Kirkwood together with Dove and Armada ones,
> >> which will not work at all. Kirkwood is armv5, while the others
> >> are armv7. There is no way you run a multiv7 barebox on kirkwood,
> >> right?
> > 
> > Oh, I didn't realize that Kirkwood is armv5. It should work though.
> > The only reason to additionally add a mvebu_v7_config is to make
> > Thumb2 mode available to the SoCs that support it.
> 
> I did some initial testing on Kirkwood Guruplug. In mvebu_defconfig
> you select CONFIG_AEABI=y resulting in
> 
> $ readelf -h barebox | grep Flags
>   Flags:                             0x5000000, Version5 EABI
> 
> And failing on Kirkwood at some places with
> 
> Board: Globalscale Technologies Guruplug Server Plus
> SoC: Marvell 6281 rev 3
> mdio_bus: miibus0: probed
> unable to handle paging request at address 0x01f0ebac
> pc : [<03e0de20>]    lr : [<03e0de08>]
> sp : 03fffeb0  ip : 03fffea8  fp : 00000001
> r10: 03ff4000  r9 : 01000e00  r8 : 01003a84
> r7 : 01f07324  r6 : 03e55f88  r5 : 01f0eaa4  r4 : 01f0eaa8
> r3 : 00000000  r2 : 00000040  r1 : 00000104  r0 : 01f11094
> Flags: Nzcv  IRQs off  FIQs off  Mode SVC_32
> [<03e0de20>] (mdio_bus_probe+0x150/0x188) from [<03e0cb24>]
> (device_probe+0x1c/0x70)
> [<03e0cb24>] (device_probe+0x1c/0x70) from [<03e0cbbc>]
> (match.part.2+0x44/0x50)
> [<03e0cbbc>] (match.part.2+0x44/0x50) from [<03e0cda8>]
> (register_device+0x118/0x168)
> [<03e0cda8>] (register_device+0x118/0x168) from [<03e0d2e8>]
> (phy_register_device+0x2c/0x94)
> [<03e0d2e8>] (phy_register_device+0x2c/0x94) from [<03e0df9c>]
> (mdiobus_register+0x144/0x18c)
> [<03e0df9c>] (mdiobus_register+0x144/0x18c) from [<03e0ce8c>]
> (platform_probe+0x10/0x14)
> [<03e0ce8c>] (platform_probe+0x10/0x14) from [<03e0cb24>]
> (device_probe+0x1c/0x70)
> [<03e0cb24>] (device_probe+0x1c/0x70) from [<03e0cbbc>]
> (match.part.2+0x44/0x50)
> [<03e0cbbc>] (match.part.2+0x44/0x50) from [<03e0cc58>]
> (register_driver+0x90/0xc8)
> [<03e0cc58>] (register_driver+0x90/0xc8) from [<03e00ae8>]
> (start_barebox+0x28/0x130)
> [<03e00ae8>] (start_barebox+0x28/0x130) from [<03e3e3e8>]
> (__start+0xf8/0x10c)
> [<03e3e3e8>] (__start+0xf8/0x10c) from [<03e00004>]
> (__bare_init_start+0x0/0x10)
> 
> [<03e3dce0>] (unwind_backtrace+0x0/0xa0) from [<03e240a8>] (panic+0x28/0x48)
> [<03e240a8>] (panic+0x28/0x48) from [<03e3e220>] (do_exception+0x10/0x14)
> [<03e3e220>] (do_exception+0x10/0x14) from [<03e3e2ac>]
> (do_data_abort+0x2c/0x38)
> [<03e3e2ac>] (do_data_abort+0x2c/0x38) from [<03e3dee8>]
> (data_abort+0x48/0x60)
> 
> I first noticed that with orion-mdio disabled and on calling
> devinfo. Looks like u64 dereferencing is definitely causing
> this but I admit, I haven't looked at mdio.

Uh, that's strange. I never had any problems with enabling/disabling this
options.

> 
> Disabling CONFIG_AEABI gives
> 
> $ readelf -h barebox | grep Flags
>   Flags:                             0x600, GNU EABI, software FP, VFP
> 
> which also works in a Multi-SoC image on Kirkwood.
> 
> >>>  #
> >>>
> >>> -if ARCH_KIRKWOOD
> > 
> > Instead of removing this I could turn this into
> > 
> > comment "Kirkwood based boards"
> 
> I am not too much into v5/v7 differences (or EABI FWIW). If
> you say, a multi_v5+v7 image is fine, I am too.

In the Kernel compiling for armv5 and armv7 is not possible due to
changes in the spinlock implementations. Doing that would involve
patching the Kernel binary during startup. We don't have locking
in barebox. So until we introduce locking we don't have a problem ;)

> 
> I'll continue testing on !KIRKWOOD tomorrow evening.

Thanks

Sascha

-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |