[PATCH 01/10] USB: import ch11.h from Linux
Sebastian Hesselbarth
sebastian.hesselbarth at gmail.com
Wed Jul 23 06:51:42 PDT 2014
Linux has an extra include for chapter 11 (Hub Specification) of USB 2.0
spec. We already have a ch9.h, so import the one from Linux.
Barebox specific changes will be patched up later.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth at gmail.com>
---
To: Sascha Hauer <s.hauer at pengutronix.de>
Cc: barebox at lists.infradead.org
---
include/usb/ch11.h | 277 +++++++++++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 277 insertions(+)
create mode 100644 include/usb/ch11.h
diff --git a/include/usb/ch11.h b/include/usb/ch11.h
new file mode 100644
index 000000000000..331499d597fa
--- /dev/null
+++ b/include/usb/ch11.h
@@ -0,0 +1,277 @@
+/*
+ * This file holds Hub protocol constants and data structures that are
+ * defined in chapter 11 (Hub Specification) of the USB 2.0 specification.
+ *
+ * It is used/shared between the USB core, the HCDs and couple of other USB
+ * drivers.
+ */
+
+#ifndef __LINUX_CH11_H
+#define __LINUX_CH11_H
+
+#include <linux/types.h> /* __u8 etc */
+
+/* This is arbitrary.
+ * From USB 2.0 spec Table 11-13, offset 7, a hub can
+ * have up to 255 ports. The most yet reported is 10.
+ *
+ * Current Wireless USB host hardware (Intel i1480 for example) allows
+ * up to 22 devices to connect. Upcoming hardware might raise that
+ * limit. Because the arrays need to add a bit for hub status data, we
+ * use 31, so plus one evens out to four bytes.
+ */
+#define USB_MAXCHILDREN 31
+
+/*
+ * Hub request types
+ */
+
+#define USB_RT_HUB (USB_TYPE_CLASS | USB_RECIP_DEVICE)
+#define USB_RT_PORT (USB_TYPE_CLASS | USB_RECIP_OTHER)
+
+/*
+ * Hub class requests
+ * See USB 2.0 spec Table 11-16
+ */
+#define HUB_CLEAR_TT_BUFFER 8
+#define HUB_RESET_TT 9
+#define HUB_GET_TT_STATE 10
+#define HUB_STOP_TT 11
+
+/*
+ * Hub class additional requests defined by USB 3.0 spec
+ * See USB 3.0 spec Table 10-6
+ */
+#define HUB_SET_DEPTH 12
+#define HUB_GET_PORT_ERR_COUNT 13
+
+/*
+ * Hub Class feature numbers
+ * See USB 2.0 spec Table 11-17
+ */
+#define C_HUB_LOCAL_POWER 0
+#define C_HUB_OVER_CURRENT 1
+
+/*
+ * Port feature numbers
+ * See USB 2.0 spec Table 11-17
+ */
+#define USB_PORT_FEAT_CONNECTION 0
+#define USB_PORT_FEAT_ENABLE 1
+#define USB_PORT_FEAT_SUSPEND 2 /* L2 suspend */
+#define USB_PORT_FEAT_OVER_CURRENT 3
+#define USB_PORT_FEAT_RESET 4
+#define USB_PORT_FEAT_L1 5 /* L1 suspend */
+#define USB_PORT_FEAT_POWER 8
+#define USB_PORT_FEAT_LOWSPEED 9 /* Should never be used */
+#define USB_PORT_FEAT_C_CONNECTION 16
+#define USB_PORT_FEAT_C_ENABLE 17
+#define USB_PORT_FEAT_C_SUSPEND 18
+#define USB_PORT_FEAT_C_OVER_CURRENT 19
+#define USB_PORT_FEAT_C_RESET 20
+#define USB_PORT_FEAT_TEST 21
+#define USB_PORT_FEAT_INDICATOR 22
+#define USB_PORT_FEAT_C_PORT_L1 23
+
+/*
+ * Port feature selectors added by USB 3.0 spec.
+ * See USB 3.0 spec Table 10-7
+ */
+#define USB_PORT_FEAT_LINK_STATE 5
+#define USB_PORT_FEAT_U1_TIMEOUT 23
+#define USB_PORT_FEAT_U2_TIMEOUT 24
+#define USB_PORT_FEAT_C_PORT_LINK_STATE 25
+#define USB_PORT_FEAT_C_PORT_CONFIG_ERROR 26
+#define USB_PORT_FEAT_REMOTE_WAKE_MASK 27
+#define USB_PORT_FEAT_BH_PORT_RESET 28
+#define USB_PORT_FEAT_C_BH_PORT_RESET 29
+#define USB_PORT_FEAT_FORCE_LINKPM_ACCEPT 30
+
+#define USB_PORT_LPM_TIMEOUT(p) (((p) & 0xff) << 8)
+
+/* USB 3.0 hub remote wake mask bits, see table 10-14 */
+#define USB_PORT_FEAT_REMOTE_WAKE_CONNECT (1 << 8)
+#define USB_PORT_FEAT_REMOTE_WAKE_DISCONNECT (1 << 9)
+#define USB_PORT_FEAT_REMOTE_WAKE_OVER_CURRENT (1 << 10)
+
+/*
+ * Hub Status and Hub Change results
+ * See USB 2.0 spec Table 11-19 and Table 11-20
+ */
+struct usb_port_status {
+ __le16 wPortStatus;
+ __le16 wPortChange;
+} __attribute__ ((packed));
+
+/*
+ * wPortStatus bit field
+ * See USB 2.0 spec Table 11-21
+ */
+#define USB_PORT_STAT_CONNECTION 0x0001
+#define USB_PORT_STAT_ENABLE 0x0002
+#define USB_PORT_STAT_SUSPEND 0x0004
+#define USB_PORT_STAT_OVERCURRENT 0x0008
+#define USB_PORT_STAT_RESET 0x0010
+#define USB_PORT_STAT_L1 0x0020
+/* bits 6 to 7 are reserved */
+#define USB_PORT_STAT_POWER 0x0100
+#define USB_PORT_STAT_LOW_SPEED 0x0200
+#define USB_PORT_STAT_HIGH_SPEED 0x0400
+#define USB_PORT_STAT_TEST 0x0800
+#define USB_PORT_STAT_INDICATOR 0x1000
+/* bits 13 to 15 are reserved */
+
+/*
+ * Additions to wPortStatus bit field from USB 3.0
+ * See USB 3.0 spec Table 10-10
+ */
+#define USB_PORT_STAT_LINK_STATE 0x01e0
+#define USB_SS_PORT_STAT_POWER 0x0200
+#define USB_SS_PORT_STAT_SPEED 0x1c00
+#define USB_PORT_STAT_SPEED_5GBPS 0x0000
+/* Valid only if port is enabled */
+/* Bits that are the same from USB 2.0 */
+#define USB_SS_PORT_STAT_MASK (USB_PORT_STAT_CONNECTION | \
+ USB_PORT_STAT_ENABLE | \
+ USB_PORT_STAT_OVERCURRENT | \
+ USB_PORT_STAT_RESET)
+
+/*
+ * Definitions for PORT_LINK_STATE values
+ * (bits 5-8) in wPortStatus
+ */
+#define USB_SS_PORT_LS_U0 0x0000
+#define USB_SS_PORT_LS_U1 0x0020
+#define USB_SS_PORT_LS_U2 0x0040
+#define USB_SS_PORT_LS_U3 0x0060
+#define USB_SS_PORT_LS_SS_DISABLED 0x0080
+#define USB_SS_PORT_LS_RX_DETECT 0x00a0
+#define USB_SS_PORT_LS_SS_INACTIVE 0x00c0
+#define USB_SS_PORT_LS_POLLING 0x00e0
+#define USB_SS_PORT_LS_RECOVERY 0x0100
+#define USB_SS_PORT_LS_HOT_RESET 0x0120
+#define USB_SS_PORT_LS_COMP_MOD 0x0140
+#define USB_SS_PORT_LS_LOOPBACK 0x0160
+
+/*
+ * wPortChange bit field
+ * See USB 2.0 spec Table 11-22 and USB 2.0 LPM ECN Table-4.10
+ * Bits 0 to 5 shown, bits 6 to 15 are reserved
+ */
+#define USB_PORT_STAT_C_CONNECTION 0x0001
+#define USB_PORT_STAT_C_ENABLE 0x0002
+#define USB_PORT_STAT_C_SUSPEND 0x0004
+#define USB_PORT_STAT_C_OVERCURRENT 0x0008
+#define USB_PORT_STAT_C_RESET 0x0010
+#define USB_PORT_STAT_C_L1 0x0020
+/*
+ * USB 3.0 wPortChange bit fields
+ * See USB 3.0 spec Table 10-11
+ */
+#define USB_PORT_STAT_C_BH_RESET 0x0020
+#define USB_PORT_STAT_C_LINK_STATE 0x0040
+#define USB_PORT_STAT_C_CONFIG_ERROR 0x0080
+
+/*
+ * wHubCharacteristics (masks)
+ * See USB 2.0 spec Table 11-13, offset 3
+ */
+#define HUB_CHAR_LPSM 0x0003 /* Logical Power Switching Mode mask */
+#define HUB_CHAR_COMMON_LPSM 0x0000 /* All ports power control at once */
+#define HUB_CHAR_INDV_PORT_LPSM 0x0001 /* per-port power control */
+#define HUB_CHAR_NO_LPSM 0x0002 /* no power switching */
+
+#define HUB_CHAR_COMPOUND 0x0004 /* hub is part of a compound device */
+
+#define HUB_CHAR_OCPM 0x0018 /* Over-Current Protection Mode mask */
+#define HUB_CHAR_COMMON_OCPM 0x0000 /* All ports Over-Current reporting */
+#define HUB_CHAR_INDV_PORT_OCPM 0x0008 /* per-port Over-current reporting */
+#define HUB_CHAR_NO_OCPM 0x0010 /* No Over-current Protection support */
+
+#define HUB_CHAR_TTTT 0x0060 /* TT Think Time mask */
+#define HUB_CHAR_PORTIND 0x0080 /* per-port indicators (LEDs) */
+
+struct usb_hub_status {
+ __le16 wHubStatus;
+ __le16 wHubChange;
+} __attribute__ ((packed));
+
+/*
+ * Hub Status & Hub Change bit masks
+ * See USB 2.0 spec Table 11-19 and Table 11-20
+ * Bits 0 and 1 for wHubStatus and wHubChange
+ * Bits 2 to 15 are reserved for both
+ */
+#define HUB_STATUS_LOCAL_POWER 0x0001
+#define HUB_STATUS_OVERCURRENT 0x0002
+#define HUB_CHANGE_LOCAL_POWER 0x0001
+#define HUB_CHANGE_OVERCURRENT 0x0002
+
+
+/*
+ * Hub descriptor
+ * See USB 2.0 spec Table 11-13
+ */
+
+#define USB_DT_HUB (USB_TYPE_CLASS | 0x09)
+#define USB_DT_SS_HUB (USB_TYPE_CLASS | 0x0a)
+#define USB_DT_HUB_NONVAR_SIZE 7
+#define USB_DT_SS_HUB_SIZE 12
+
+/*
+ * Hub Device descriptor
+ * USB Hub class device protocols
+ */
+
+#define USB_HUB_PR_FS 0 /* Full speed hub */
+#define USB_HUB_PR_HS_NO_TT 0 /* Hi-speed hub without TT */
+#define USB_HUB_PR_HS_SINGLE_TT 1 /* Hi-speed hub with single TT */
+#define USB_HUB_PR_HS_MULTI_TT 2 /* Hi-speed hub with multiple TT */
+#define USB_HUB_PR_SS 3 /* Super speed hub */
+
+struct usb_hub_descriptor {
+ __u8 bDescLength;
+ __u8 bDescriptorType;
+ __u8 bNbrPorts;
+ __le16 wHubCharacteristics;
+ __u8 bPwrOn2PwrGood;
+ __u8 bHubContrCurrent;
+
+ /* 2.0 and 3.0 hubs differ here */
+ union {
+ struct {
+ /* add 1 bit for hub status change; round to bytes */
+ __u8 DeviceRemovable[(USB_MAXCHILDREN + 1 + 7) / 8];
+ __u8 PortPwrCtrlMask[(USB_MAXCHILDREN + 1 + 7) / 8];
+ } __attribute__ ((packed)) hs;
+
+ struct {
+ __u8 bHubHdrDecLat;
+ __le16 wHubDelay;
+ __le16 DeviceRemovable;
+ } __attribute__ ((packed)) ss;
+ } u;
+} __attribute__ ((packed));
+
+/* port indicator status selectors, tables 11-7 and 11-25 */
+#define HUB_LED_AUTO 0
+#define HUB_LED_AMBER 1
+#define HUB_LED_GREEN 2
+#define HUB_LED_OFF 3
+
+enum hub_led_mode {
+ INDICATOR_AUTO = 0,
+ INDICATOR_CYCLE,
+ /* software blinks for attention: software, hardware, reserved */
+ INDICATOR_GREEN_BLINK, INDICATOR_GREEN_BLINK_OFF,
+ INDICATOR_AMBER_BLINK, INDICATOR_AMBER_BLINK_OFF,
+ INDICATOR_ALT_BLINK, INDICATOR_ALT_BLINK_OFF
+} __attribute__ ((packed));
+
+/* Transaction Translator Think Times, in bits */
+#define HUB_TTTT_8_BITS 0x00
+#define HUB_TTTT_16_BITS 0x20
+#define HUB_TTTT_24_BITS 0x40
+#define HUB_TTTT_32_BITS 0x60
+
+#endif /* __LINUX_CH11_H */
--
2.0.0
More information about the barebox
mailing list