Beagleboard: crash during the boot time

[ManuelCurcio at Eaton.com]

Hi,

I try to run barebox on the beagleboard with the default configuration
(am335x_defconfig & am335x_mlo_defconfig), however the board crashes
with the following trace : 


barebox 2014.12.0-00117-g631be8e #61 Wed Dec 24 14:58:09 GMT 2014


Board: TI AM335x BeagleBone
detected 'BeagleBone White'
omap-hsmmc 48060000.mmc: registered as 48060000.mmc
booting from MMC
mmc0: detected SD card version 2.0
mmc0: registered mmc0


barebox 2014.12.0-00117-g631be8e #60 Wed Dec 24 14:58:02 GMT 2014


Board: TI AM335x BeagleBone
detected 'BeagleBone White'
cpsw 4a100000.ethernet: detected phy mask 0x1
mdio_bus: miibus0: probed
eth0: got preset MAC address: 00:18:31:8e:61:71
cpsw 4a100000.ethernet: probe failed: I/O error
unable to handle paging request at address 0x6e6f62f2
pc : [<8fe2e29e>]    lr : [<8fe0764d>]
sp : 8ffffe68  ip : 87f1f068  fp : 8fe62a40
r10: 87f1f040  r9 : 87f12078  r8 : 87f1f0fc
r7 : ffffffff  r6 : 87f1f068  r5 : 8fe62a40  r4 : 6e6f62f2
r3 : 00000000  r2 : 00000000  r1 : 87f1f068  r0 : 6e6f62f2
Flags: nZCV  IRQs off  FIQs on  Mode SVC_32
[<8fe2e29e>] (strcmp+0xc/0x1a) from [<8fe0764d>] (get_device_by_name_id
+0x19/0x38)
[<8fe0764d>] (get_device_by_name_id+0x19/0x38) from [<8fe07967>]
(register_device+0x17/0xcc)
[<8fe07967>] (register_device+0x17/0xcc) from [<8fe25d6f>]
(of_platform_device_create+0x183/0x1b0)
[<8fe25d6f>] (of_platform_device_create+0x183/0x1b0) from [<8fe25dc7>]
(of_platform_bus_create+0x2b/0x68)
[<8fe25dc7>] (of_platform_bus_create+0x2b/0x68) from [<8fe25e4f>]
(of_platform_populate+0x23/0x40)
[<8fe25e4f>] (of_platform_populate+0x23/0x40) from [<8fe07a9f>]
(platform_probe+0x9/0xa)
[<8fe07a9f>] (platform_probe+0x9/0xa) from [<8fe07695>] (device_probe
+0x11/0x44)
[<8fe07695>] (device_probe+0x11/0x44) from [<8fe076ed>] (match.part.1
+0x25/0x2a)
[<8fe076ed>] (match.part.1+0x25/0x2a) from [<8fe077f9>] (register_driver
+0x4d/0x74)
[<8fe077f9>] (register_driver+0x4d/0x74) from [<8fe0080b>]
(start_barebox+0x17/0xbc)
[<8fe0080b>] (start_barebox+0x17/0xbc) from [<8fe3cd03>] (__start
+0xa7/0xbc)
[<8fe3cd03>] (__start+0xa7/0xbc) from [<8fe00005>] (__bare_init_start
+0x1/0xc)

[<8fe3c729>] (unwind_backtrace+0x1/0x58) from [<8fe2ed4d>] (panic
+0x1d/0x34)
[<8fe2ed4d>] (panic+0x1d/0x34) from [<8fe3cbc1>] (do_exception+0xd/0x10)
[<8fe3cbc1>] (do_exception+0xd/0x10) from [<8fe3cc29>] (do_data_abort
+0x21/0x2c)
[<8fe3cc29>] (do_data_abort+0x21/0x2c) from [<8fe3c8e8>] (data_abort
+0x48/0x60)


If I remove the ethernet driver of the configuration, barebox doesn't
crash. 
Some one knows this issue ? Some one have a solution or can help me to
find a solution  ?

Thanks you ! & Merry Christmas !

Best regards

Manuel 


-----------------------------
Eaton Industries (France) S.A.S ~ Siège social: 110 Rue Blaise Pascal, Immeuble Le Viséo - Bâtiment A Innovallée, 38330, Montbonnot-St.-Martin, France ~ Lieu d'enregistrement au registre du commerce: Grenoble ~ Numéro d'enregistrement: 509 653 176 ~ Capital social souscrit et liberé:€ 16215441 ~ Numéro de TVA: FR47509653176

-----------------------------