[PATCH 1/5] mtd: nand: remove NAND_ATMEL_PMECC

[Raphaël Poggi]

Ok, I did it because we need a structure member to retrieve
"atmel,has-pmecc" from device tree.

Is this ok if I add the has_pmecc member (feed by atmel_nand_of_init),
let the NAND_ATMEL_PMECC, and the if will be like :

if (IS_ENABLED(CONFIG_NAND_ATMEL_PMECC) || pdata->has_pmecc)

With this we can handle device tree/non device tree probing.

Or maybe you have a better idea.

Best regards,
Raphaël Poggi

2014-08-06 6:08 GMT+02:00 Jean-Christophe PLAGNIOL-VILLARD
<plagnioj at jcrosoft.com>:
> On 11:14 Tue 05 Aug     , Rapha??l Poggi wrote:
>> By removing this CONFIG_, we can use a structure member to retrieve the config,
>> either through the plateform data or through the device tree. So we can handle cases
>> when the driver is probed using device tree or not.
> NACK
>
> this is use to reduce barebox size
>
> keep the NAND_ATMEL_PMECC
>
> so we choose to enable it or not
>
> Best Regards,
> J.
>>
>> Signed-off-by: Raphaël Poggi <poggi.raph at gmail.com>
>> ---
>>  arch/arm/mach-at91/include/mach/board.h |    1 +
>>  drivers/mtd/nand/Kconfig                |    8 --------
>>  drivers/mtd/nand/atmel_nand.c           |    2 +-
>>  3 files changed, 2 insertions(+), 9 deletions(-)
>>
>> diff --git a/arch/arm/mach-at91/include/mach/board.h b/arch/arm/mach-at91/include/mach/board.h
>> index aa0fdae..e2307ed 100644
>> --- a/arch/arm/mach-at91/include/mach/board.h
>> +++ b/arch/arm/mach-at91/include/mach/board.h
>> @@ -63,6 +63,7 @@ struct atmel_nand_data {
>>       u8              bus_width_16;   /* buswidth is 16 bit */
>>       u8              ecc_mode;       /* NAND_ECC_* */
>>       u8              on_flash_bbt;   /* Use flash based bbt */
>> +     u8              has_pmecc;      /* Use PMECC */
>>       u8              bus_on_d0;
>>
>>       u8              pmecc_corr_cap;
>> diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
>> index 04fe3c8..d49eae3 100644
>> --- a/drivers/mtd/nand/Kconfig
>> +++ b/drivers/mtd/nand/Kconfig
>> @@ -95,14 +95,6 @@ config NAND_ATMEL
>>       prompt "Atmel (AT91SAM9xxx) NAND driver"
>>       depends on ARCH_AT91
>>
>> -config NAND_ATMEL_PMECC
>> -     bool
>> -     prompt "PMECC support"
>> -     depends on NAND_ATMEL
>> -     select NAND_ECC_HW
>> -     help
>> -       Support for PMECC present on the SoC sam9x5 and sam9n12
>> -
>>  config NAND_S3C24XX
>>       bool
>>       prompt "Samsung S3C24XX NAND driver"
>> diff --git a/drivers/mtd/nand/atmel_nand.c b/drivers/mtd/nand/atmel_nand.c
>> index 337e225..3ec6450 100644
>> --- a/drivers/mtd/nand/atmel_nand.c
>> +++ b/drivers/mtd/nand/atmel_nand.c
>> @@ -1219,7 +1219,7 @@ static int __init atmel_nand_probe(struct device_d *dev)
>>
>>       if (IS_ENABLED(CONFIG_NAND_ECC_HW) &&
>>           nand_chip->ecc.mode == NAND_ECC_HW) {
>> -             if (IS_ENABLED(CONFIG_NAND_ATMEL_PMECC))
>> +             if (pdata->has_pmecc)
>>                       res = atmel_pmecc_nand_init_params(dev, host);
>>               else
>>                       res = atmel_hw_nand_init_params(dev, host);
>> --
>> 1.7.9.5
>>
>>
>> _______________________________________________
>> barebox mailing list
>> barebox at lists.infradead.org
>> http://lists.infradead.org/mailman/listinfo/barebox
>
> _______________________________________________
> barebox mailing list
> barebox at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/barebox