[PATCH] i.MX28: unbreak ethernet

[Eric Bénard]

since the switch to common clock, ethernet driver doesn't works and
and access to the network leads to :
eth0: Read MDIO failed...
unable to handle NULL pointer dereference at address 0x000000c7

The problem is that bit 31 (SLEEP) of register HW_CLKCTRL_ENET is kept
to its default value (1) which means : "put Ethernet block in sleep mode.
CLK_H_MAC0(1), CLK_H_MAC0(1)_S, and CLK_ENET0(1)_TX are gated off.
Ethernet can be wakeup remotely in sleep mode"
In that case the FEC don't get its clock.

This patch fix the problem by toggling this bit when FEC's clock is
enabled.

Tested on i.MX28EVK.

Signed-off-by: Eric Bénard <eric at eukrea.com>
---
 drivers/clk/mxs/clk-imx28.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/drivers/clk/mxs/clk-imx28.c b/drivers/clk/mxs/clk-imx28.c
index ed38d4b..05b3c2a 100644
--- a/drivers/clk/mxs/clk-imx28.c
+++ b/drivers/clk/mxs/clk-imx28.c
@@ -68,7 +68,7 @@ enum imx28_clk {
 	emi_xtal, lcdif_div, etm_div, ptp, saif0_div, saif1_div,
 	clk32k_div, rtc, lradc, spdif_div, clk32k, pwm, uart, ssp0,
 	ssp1, ssp2, ssp3, gpmi, spdif, emi, saif0, saif1, lcdif, etm,
-	fec, can0, can1, usb0, usb1, usb0_phy, usb1_phy, enet_out,
+	fec_sleep, fec, can0, can1, usb0, usb1, usb0_phy, usb1_phy, enet_out,
 	lcdif_comp, clk_max
 };
 
@@ -124,7 +124,8 @@ int __init mx28_clocks_init(void __iomem *regs)
 	clks[emi] = mxs_clk_gate("emi", "emi_sel", EMI, 31);
 	clks[lcdif] = mxs_clk_gate("lcdif", "lcdif_div", LCDIF, 31);
 	clks[etm] = mxs_clk_gate("etm", "etm_div", ETM, 31);
-	clks[fec] = mxs_clk_gate("fec", "hbus", ENET, 30);
+	clks[fec_sleep] = mxs_clk_gate("fec_sleep", "hbus", ENET, 31);
+	clks[fec] = mxs_clk_gate("fec", "fec_sleep", ENET, 30);
 	clks[usb0_phy] = mxs_clk_gate("usb0_phy", "pll0", PLL0CTRL0, 18);
 	clks[usb1_phy] = mxs_clk_gate("usb1_phy", "pll1", PLL1CTRL0, 18);
 	clks[enet_out] = clk_gate("enet_out", "pll2", ENET, 18);
-- 
1.8.3.1