[PATCH 2/3] Add DMO RealQ7 board support

[Sascha Hauer]

On Fri, Mar 08, 2013 at 01:51:38PM +0100, Jean-Christophe PLAGNIOL-VILLARD wrote:
> > +
> > +static void mmd_write_reg(struct phy_device *dev, int device, int reg, int val)
> > +{
> > +	phy_write(dev, 0x0d, device);
> > +	phy_write(dev, 0x0e, reg);
> > +	phy_write(dev, 0x0d, (1 << 14) | device);
> > +	phy_write(dev, 0x0e, val);
> > +}
> > +
> > +static void mx6_rgmii_rework(struct phy_device *dev)
> > +{
> > +	/*
> > +	 * min rx data delay, max rx/tx clock delay,
> > +	 * min rx/tx control delay
> > +	 */
> > +	mmd_write_reg(dev, 2, 4, 0);
> > +	mmd_write_reg(dev, 2, 5, 0);
> > +	mmd_write_reg(dev, 2, 8, 0x003ff);
> > +}
> > +
> > +static struct fec_platform_data fec_info = {
> > +	.xcv_type = RGMII,
> > +	.phy_init = mx6_rgmii_rework,
> > +	.phy_addr = -1,
> use phy_fix_up as done on sama5d3xek
> 
> the phy_init need do be dropped now
> > +};
> > +
> > +static void realq7_enet_init(void)
> > +{
> > +	mxc_iomux_v3_setup_multiple_pads(realq7_pads_gpio, ARRAY_SIZE(realq7_pads_gpio));
> > +	gpio_direction_output(RQ7_GPIO_ENET_PHYADD2, 0);
> > +	gpio_direction_output(RQ7_GPIO_ENET_MODE0, 1);
> > +	gpio_direction_output(RQ7_GPIO_ENET_MODE1, 1);
> > +	gpio_direction_output(RQ7_GPIO_ENET_MODE2, 1);
> > +	gpio_direction_output(RQ7_GPIO_ENET_MODE3, 1);
> > +	gpio_direction_output(RQ7_GPIO_ENET_EN_CLK125, 1);
> > +
> > +	gpio_direction_output(25, 0);
> > +	mdelay(50);
> > +
> > +	gpio_direction_output(25, 1);
> > +	mdelay(50);
> > +
> > +	mxc_iomux_v3_setup_multiple_pads(realq7_pads_enet, ARRAY_SIZE(realq7_pads_enet));
> > +
> > +	imx6_add_fec(&fec_info);
> > +}
> > +
> > +static int realq7_mem_init(void)
> > +{
> > +	arm_add_mem_device("ram0", 0x10000000, SZ_2G);
> > +
> > +	return 0;
> > +}
> > +mem_initcall(realq7_mem_init);
> > +
> > +static int realq7_spi_cs[] = { IMX_GPIO_NR(1, 12), };
> > +
> > +static struct spi_imx_master realq7_spi_0_data = {
> > +	.chipselect = realq7_spi_cs,
> > +	.num_chipselect = ARRAY_SIZE(realq7_spi_cs),
> > +};
> > +
> > +static const struct spi_board_info realq7_spi_board_info[] = {
> > +	{
> > +		.name = "m25p80",
> > +		.max_speed_hz = 40000000,
> > +		.bus_num = 4,
> > +		.chip_select = 0,
> > +	}
> > +};
> > +
> > +static struct esdhc_platform_data realq7_emmc_data = {
> > +	.cd_type = ESDHC_CD_PERMANENT,
> > +	.caps = MMC_MODE_8BIT,
> > +	.devname = "emmc",
> > +};
> we was discussion of symlink on devfs my idea was to use it here instead of
> the devname

The sysfs symlink support alone does not fix this. Who should create the
link?

> > +
> > +	armlinux_set_bootparams((void *)0x10000100);
> > +	armlinux_set_architecture(3769);
> why a magic instead of a macro?

Can be dropped. It's devicetree only, so we don't need an architecture
id. I doubt there is one even registered.

Sascha

> > +++ b/arch/arm/boards/dmo-mx6-realq7/env/init/hostname
> > @@ -0,0 +1,8 @@
> > +#!/bin/sh
> > +
> > +if [ "$1" = menu ]; then
> > +	init-menu-add-entry "$0" "hostname"
> > +	exit
> > +fi
> > +
> > +global.hostname=realq7
> in config-board?

ok.

> > +
> > +	.boot_data.start	= APP_DEST,
> > +	.boot_data.size		= 192 * 1024,
> barebox_image_size

ok. This btw will not work with CONFIG_RELOCATABLE as is since the
linker cannot generate this value then.

> > +	reg32_write(0x021e80a4, 0x0000047f);
> > +	reg32_write(0x021e80a8, 0x0000c34f);
> > +	reg32_write(0x021e8080, 0x00000001);
> can we have not all of those magic?

No, I won't do the decoding now. This time can be invested better.

Sascha

-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |