[PATCH 2/5] usb/gadget: add pxa27x_udc driver
Robert Jarzmik
robert.jarzmik at free.fr
Wed Nov 23 22:01:27 EST 2011
From: Robert Jarzmik <robert.jarzmik at atosorigin.com>
Adapt mainline kernel pxa27x_udc driver to barebox :
- remove function header comments as they are in mainline
- test it with serial gadget
Signed-off-by: Robert Jarzmik <robert.jarzmik at free.fr>
---
arch/arm/mach-pxa/include/mach/udc_pxa2xx.h | 26 +
drivers/usb/gadget/Kconfig | 7 +
drivers/usb/gadget/Makefile | 1 +
drivers/usb/gadget/pxa27x_udc.c | 1524 +++++++++++++++++++++++++++
drivers/usb/gadget/pxa27x_udc.h | 393 +++++++
5 files changed, 1951 insertions(+), 0 deletions(-)
create mode 100644 arch/arm/mach-pxa/include/mach/udc_pxa2xx.h
create mode 100644 drivers/usb/gadget/pxa27x_udc.c
create mode 100644 drivers/usb/gadget/pxa27x_udc.h
diff --git a/arch/arm/mach-pxa/include/mach/udc_pxa2xx.h b/arch/arm/mach-pxa/include/mach/udc_pxa2xx.h
new file mode 100644
index 0000000..dcdd36a
--- /dev/null
+++ b/arch/arm/mach-pxa/include/mach/udc_pxa2xx.h
@@ -0,0 +1,26 @@
+/*
+ * arch/arm/mach-pxa/include/mach/udc_pxa2xx.h
+ *
+ * This supports machine-specific differences in how the PXA2xx
+ * USB Device Controller (UDC) is wired.
+ *
+ * It is set in linux/arch/arm/mach-pxa/<machine>.c or in
+ * linux/arch/mach-ixp4xx/<machine>.c and used in
+ * the probe routine of linux/drivers/usb/gadget/pxa2xx_udc.c
+ */
+
+struct pxa2xx_udc_mach_info {
+ int (*udc_is_connected)(void); /* do we see host? */
+ void (*udc_command)(int cmd);
+#define PXA2XX_UDC_CMD_CONNECT 0 /* let host see us */
+#define PXA2XX_UDC_CMD_DISCONNECT 1 /* so host won't see us */
+
+ /* Boards following the design guidelines in the developer's manual,
+ * with on-chip GPIOs not Lubbock's weird hardware, can have a sane
+ * VBUS IRQ and omit the methods above. Store the GPIO number
+ * here. Note that sometimes the signals go through inverters...
+ */
+ bool gpio_pullup_inverted;
+ int gpio_pullup; /* high == pullup activated */
+};
+
diff --git a/drivers/usb/gadget/Kconfig b/drivers/usb/gadget/Kconfig
index b8375c6..472c591 100644
--- a/drivers/usb/gadget/Kconfig
+++ b/drivers/usb/gadget/Kconfig
@@ -14,6 +14,13 @@ config USB_GADGET_DRIVER_ARC
prompt "Arc OTG device core"
depends on ARCH_IMX
select USB_GADGET_DUALSPEED
+
+config USB_GADGET_DRIVER_PXA27X
+ bool
+ prompt "PXA27x gadget driver"
+ depends on ARCH_PXA
+ select USB_GADGET_DUALSPEED
+ select POLLER
endchoice
choice
diff --git a/drivers/usb/gadget/Makefile b/drivers/usb/gadget/Makefile
index 804bb91..e034786 100644
--- a/drivers/usb/gadget/Makefile
+++ b/drivers/usb/gadget/Makefile
@@ -3,3 +3,4 @@ obj-$(CONFIG_USB_GADGET) += composite.o config.o usbstring.o epautoconf.o
obj-$(CONFIG_USB_GADGET_SERIAL) += u_serial.o serial.o f_serial.o f_acm.o
obj-$(CONFIG_USB_GADGET_DFU) += dfu.o
obj-$(CONFIG_USB_GADGET_DRIVER_ARC) += fsl_udc.o
+obj-$(CONFIG_USB_GADGET_DRIVER_PXA27X) += pxa27x_udc.o
diff --git a/drivers/usb/gadget/pxa27x_udc.c b/drivers/usb/gadget/pxa27x_udc.c
new file mode 100644
index 0000000..d0dbee9
--- /dev/null
+++ b/drivers/usb/gadget/pxa27x_udc.c
@@ -0,0 +1,1524 @@
+/*
+ * Handles the Intel 27x USB Device Controller (UDC)
+ *
+ * Inspired by original driver by Frank Becker, David Brownell, and others.
+ * Copyright (C) 2008 Robert Jarzmik
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ * Taken from linux-2.6 kernel and adapted to barebox.
+ */
+#include <common.h>
+#include <errno.h>
+#include <clock.h>
+#include <io.h>
+#include <gpio.h>
+#include <init.h>
+#include <poller.h>
+
+#include <usb/ch9.h>
+#include <usb/gadget.h>
+
+#include "pxa27x_udc.h"
+#include <mach/udc_pxa2xx.h>
+#include <mach/pxa-regs.h>
+
+#define DRIVER_VERSION "2008-04-18"
+#define DRIVER_DESC "PXA 27x USB Device Controller driver"
+
+static const char driver_name[] = "pxa27x_udc";
+static struct pxa_udc *the_controller;
+
+static void handle_ep(struct pxa_ep *ep);
+
+static int is_match_usb_pxa(struct udc_usb_ep *udc_usb_ep, struct pxa_ep *ep,
+ int config, int interface, int altsetting)
+{
+ if (usb_endpoint_num(&udc_usb_ep->desc) != ep->addr)
+ return 0;
+ if (usb_endpoint_dir_in(&udc_usb_ep->desc) != ep->dir_in)
+ return 0;
+ if (usb_endpoint_type(&udc_usb_ep->desc) != ep->type)
+ return 0;
+ if ((ep->config != config) || (ep->interface != interface)
+ || (ep->alternate != altsetting))
+ return 0;
+ return 1;
+}
+
+static struct pxa_ep *find_pxa_ep(struct pxa_udc *udc,
+ struct udc_usb_ep *udc_usb_ep)
+{
+ int i;
+ struct pxa_ep *ep;
+ int cfg = udc->config;
+ int iface = udc->last_interface;
+ int alt = udc->last_alternate;
+
+ if (udc_usb_ep == &udc->udc_usb_ep[0])
+ return &udc->pxa_ep[0];
+
+ for (i = 1; i < NR_PXA_ENDPOINTS; i++) {
+ ep = &udc->pxa_ep[i];
+ if (is_match_usb_pxa(udc_usb_ep, ep, cfg, iface, alt))
+ return ep;
+ }
+ return NULL;
+}
+
+static void update_pxa_ep_matches(struct pxa_udc *udc)
+{
+ int i;
+ struct udc_usb_ep *udc_usb_ep;
+
+ for (i = 1; i < NR_USB_ENDPOINTS; i++) {
+ udc_usb_ep = &udc->udc_usb_ep[i];
+ if (udc_usb_ep->pxa_ep)
+ udc_usb_ep->pxa_ep = find_pxa_ep(udc, udc_usb_ep);
+ }
+}
+
+static void pio_irq_enable(struct pxa_ep *ep)
+{
+ struct pxa_udc *udc = ep->dev;
+ int index = EPIDX(ep);
+ u32 udcicr0 = udc_readl(udc, UDCICR0);
+ u32 udcicr1 = udc_readl(udc, UDCICR1);
+
+ if (index < 16)
+ udc_writel(udc, UDCICR0, udcicr0 | (3 << (index * 2)));
+ else
+ udc_writel(udc, UDCICR1, udcicr1 | (3 << ((index - 16) * 2)));
+}
+
+static void pio_irq_disable(struct pxa_ep *ep)
+{
+ struct pxa_udc *udc = ep->dev;
+ int index = EPIDX(ep);
+ u32 udcicr0 = udc_readl(udc, UDCICR0);
+ u32 udcicr1 = udc_readl(udc, UDCICR1);
+
+ if (index < 16)
+ udc_writel(udc, UDCICR0, udcicr0 & ~(3 << (index * 2)));
+ else
+ udc_writel(udc, UDCICR1, udcicr1 & ~(3 << ((index - 16) * 2)));
+}
+
+static inline void udc_set_mask_UDCCR(struct pxa_udc *udc, int mask)
+{
+ u32 udccr = udc_readl(udc, UDCCR);
+ udc_writel(udc, UDCCR,
+ (udccr & UDCCR_MASK_BITS) | (mask & UDCCR_MASK_BITS));
+}
+
+static inline void udc_clear_mask_UDCCR(struct pxa_udc *udc, int mask)
+{
+ u32 udccr = udc_readl(udc, UDCCR);
+ udc_writel(udc, UDCCR,
+ (udccr & UDCCR_MASK_BITS) & ~(mask & UDCCR_MASK_BITS));
+}
+
+static inline void ep_write_UDCCSR(struct pxa_ep *ep, int mask)
+{
+ if (is_ep0(ep))
+ mask |= UDCCSR0_ACM;
+ udc_ep_writel(ep, UDCCSR, mask);
+}
+
+static int ep_count_bytes_remain(struct pxa_ep *ep)
+{
+ if (ep->dir_in)
+ return -EOPNOTSUPP;
+ return udc_ep_readl(ep, UDCBCR) & 0x3ff;
+}
+
+static int ep_is_empty(struct pxa_ep *ep)
+{
+ int ret;
+
+ if (!is_ep0(ep) && ep->dir_in)
+ return -EOPNOTSUPP;
+ if (is_ep0(ep))
+ ret = !(udc_ep_readl(ep, UDCCSR) & UDCCSR0_RNE);
+ else
+ ret = !(udc_ep_readl(ep, UDCCSR) & UDCCSR_BNE);
+ return ret;
+}
+
+static int ep_is_full(struct pxa_ep *ep)
+{
+ if (is_ep0(ep))
+ return udc_ep_readl(ep, UDCCSR) & UDCCSR0_IPR;
+ if (!ep->dir_in)
+ return -EOPNOTSUPP;
+ return !(udc_ep_readl(ep, UDCCSR) & UDCCSR_BNF);
+}
+
+static int epout_has_pkt(struct pxa_ep *ep)
+{
+ if (!is_ep0(ep) && ep->dir_in)
+ return -EOPNOTSUPP;
+ if (is_ep0(ep))
+ return udc_ep_readl(ep, UDCCSR) & UDCCSR0_OPC;
+ return udc_ep_readl(ep, UDCCSR) & UDCCSR_PC;
+}
+
+static void set_ep0state(struct pxa_udc *udc, int state)
+{
+ struct pxa_ep *ep = &udc->pxa_ep[0];
+ char *old_stname = EP0_STNAME(udc);
+
+ udc->ep0state = state;
+ ep_dbg(ep, "state=%s->%s, udccsr0=0x%03x, udcbcr=%d\n", old_stname,
+ EP0_STNAME(udc), udc_ep_readl(ep, UDCCSR),
+ udc_ep_readl(ep, UDCBCR));
+}
+
+static void ep0_idle(struct pxa_udc *dev)
+{
+ set_ep0state(dev, WAIT_FOR_SETUP);
+}
+
+static __init void pxa_ep_setup(struct pxa_ep *ep)
+{
+ u32 new_udccr;
+
+ new_udccr = ((ep->config << UDCCONR_CN_S) & UDCCONR_CN)
+ | ((ep->interface << UDCCONR_IN_S) & UDCCONR_IN)
+ | ((ep->alternate << UDCCONR_AISN_S) & UDCCONR_AISN)
+ | ((EPADDR(ep) << UDCCONR_EN_S) & UDCCONR_EN)
+ | ((EPXFERTYPE(ep) << UDCCONR_ET_S) & UDCCONR_ET)
+ | ((ep->dir_in) ? UDCCONR_ED : 0)
+ | ((ep->fifo_size << UDCCONR_MPS_S) & UDCCONR_MPS)
+ | UDCCONR_EE;
+
+ udc_ep_writel(ep, UDCCR, new_udccr);
+}
+
+static __init void pxa_eps_setup(struct pxa_udc *dev)
+{
+ unsigned int i;
+
+ dev_dbg(dev->dev, "%s: dev=%p\n", __func__, dev);
+
+ for (i = 1; i < NR_PXA_ENDPOINTS; i++)
+ pxa_ep_setup(&dev->pxa_ep[i]);
+}
+
+static struct usb_request *pxa_ep_alloc_request(struct usb_ep *_ep)
+{
+ struct pxa27x_request *req;
+
+ req = xzalloc(sizeof *req);
+ if (!req)
+ return NULL;
+
+ INIT_LIST_HEAD(&req->queue);
+ req->in_use = 0;
+ req->udc_usb_ep = container_of(_ep, struct udc_usb_ep, usb_ep);
+
+ return &req->req;
+}
+
+static void pxa_ep_free_request(struct usb_ep *_ep, struct usb_request *_req)
+{
+ struct pxa27x_request *req;
+
+ req = container_of(_req, struct pxa27x_request, req);
+ WARN_ON(!list_empty(&req->queue));
+ kfree(req);
+}
+
+static void ep_add_request(struct pxa_ep *ep, struct pxa27x_request *req)
+{
+ if (unlikely(!req))
+ return;
+ ep_vdbg(ep, "req:%p, lg=%d, udccsr=0x%03x\n", req,
+ req->req.length, udc_ep_readl(ep, UDCCSR));
+
+ req->in_use = 1;
+ list_add_tail(&req->queue, &ep->queue);
+ pio_irq_enable(ep);
+}
+
+static void ep_del_request(struct pxa_ep *ep, struct pxa27x_request *req)
+{
+ if (unlikely(!req))
+ return;
+ ep_vdbg(ep, "req:%p, lg=%d, udccsr=0x%03x\n", req,
+ req->req.length, udc_ep_readl(ep, UDCCSR));
+
+ list_del_init(&req->queue);
+ req->in_use = 0;
+ if (!is_ep0(ep) && list_empty(&ep->queue))
+ pio_irq_disable(ep);
+}
+
+static void req_done(struct pxa_ep *ep, struct pxa27x_request *req, int status)
+{
+ ep_del_request(ep, req);
+ if (likely(req->req.status == -EINPROGRESS))
+ req->req.status = status;
+ else
+ status = req->req.status;
+
+ if (status && status != -ESHUTDOWN)
+ ep_dbg(ep, "complete req %p stat %d len %u/%u\n",
+ &req->req, status,
+ req->req.actual, req->req.length);
+
+ req->req.complete(&req->udc_usb_ep->usb_ep, &req->req);
+}
+
+static void ep_end_out_req(struct pxa_ep *ep, struct pxa27x_request *req)
+{
+ req_done(ep, req, 0);
+}
+
+static void ep0_end_out_req(struct pxa_ep *ep, struct pxa27x_request *req)
+{
+ set_ep0state(ep->dev, OUT_STATUS_STAGE);
+ ep_end_out_req(ep, req);
+ ep0_idle(ep->dev);
+}
+
+static void ep_end_in_req(struct pxa_ep *ep, struct pxa27x_request *req)
+{
+ req_done(ep, req, 0);
+}
+
+static void ep0_end_in_req(struct pxa_ep *ep, struct pxa27x_request *req)
+{
+ set_ep0state(ep->dev, IN_STATUS_STAGE);
+ ep_end_in_req(ep, req);
+}
+
+static void nuke(struct pxa_ep *ep, int status)
+{
+ struct pxa27x_request *req;
+
+ while (!list_empty(&ep->queue)) {
+ req = list_entry(ep->queue.next, struct pxa27x_request, queue);
+ req_done(ep, req, status);
+ }
+}
+
+static int read_packet(struct pxa_ep *ep, struct pxa27x_request *req)
+{
+ u32 *buf;
+ int bytes_ep, bufferspace, count, i;
+
+ bytes_ep = ep_count_bytes_remain(ep);
+ bufferspace = req->req.length - req->req.actual;
+
+ buf = (u32 *)(req->req.buf + req->req.actual);
+
+ if (likely(!ep_is_empty(ep)))
+ count = min(bytes_ep, bufferspace);
+ else /* zlp */
+ count = 0;
+
+ for (i = count; i > 0; i -= 4)
+ *buf++ = udc_ep_readl(ep, UDCDR);
+ req->req.actual += count;
+
+ ep_write_UDCCSR(ep, UDCCSR_PC);
+
+ return count;
+}
+
+static int write_packet(struct pxa_ep *ep, struct pxa27x_request *req,
+ unsigned int max)
+{
+ int length, count, remain, i;
+ u32 *buf;
+ u8 *buf_8;
+
+ buf = (u32 *)(req->req.buf + req->req.actual);
+ prefetch(buf);
+
+ length = min(req->req.length - req->req.actual, max);
+ req->req.actual += length;
+
+ remain = length & 0x3;
+ count = length & ~(0x3);
+ for (i = count; i > 0 ; i -= 4)
+ udc_ep_writel(ep, UDCDR, *buf++);
+
+ buf_8 = (u8 *)buf;
+ for (i = remain; i > 0; i--)
+ udc_ep_writeb(ep, UDCDR, *buf_8++);
+
+ ep_vdbg(ep, "length=%d+%d, udccsr=0x%03x\n", count, remain,
+ udc_ep_readl(ep, UDCCSR));
+
+ return length;
+}
+
+static int read_fifo(struct pxa_ep *ep, struct pxa27x_request *req)
+{
+ int count, is_short, completed = 0;
+
+ while (epout_has_pkt(ep)) {
+ count = read_packet(ep, req);
+
+ is_short = (count < ep->fifo_size);
+ ep_dbg(ep, "read udccsr:%03x, count:%d bytes%s req %p %d/%d\n",
+ udc_ep_readl(ep, UDCCSR), count, is_short ? "/S" : "",
+ &req->req, req->req.actual, req->req.length);
+
+ /* completion */
+ if (is_short || req->req.actual == req->req.length) {
+ completed = 1;
+ break;
+ }
+ /* finished that packet. the next one may be waiting... */
+ }
+ return completed;
+}
+
+static int write_fifo(struct pxa_ep *ep, struct pxa27x_request *req)
+{
+ unsigned max;
+ int count, is_short, is_last = 0, completed = 0, totcount = 0;
+ u32 udccsr;
+
+ max = ep->fifo_size;
+ do {
+ is_short = 0;
+
+ udccsr = udc_ep_readl(ep, UDCCSR);
+ if (udccsr & UDCCSR_PC) {
+ ep_vdbg(ep, "Clearing Transmit Complete, udccsr=%x\n",
+ udccsr);
+ ep_write_UDCCSR(ep, UDCCSR_PC);
+ }
+ if (udccsr & UDCCSR_TRN) {
+ ep_vdbg(ep, "Clearing Underrun on, udccsr=%x\n",
+ udccsr);
+ ep_write_UDCCSR(ep, UDCCSR_TRN);
+ }
+
+ count = write_packet(ep, req, max);
+ totcount += count;
+
+ /* last packet is usually short (or a zlp) */
+ if (unlikely(count < max)) {
+ is_last = 1;
+ is_short = 1;
+ } else {
+ if (likely(req->req.length > req->req.actual)
+ || req->req.zero)
+ is_last = 0;
+ else
+ is_last = 1;
+ /* interrupt/iso maxpacket may not fill the fifo */
+ is_short = unlikely(max < ep->fifo_size);
+ }
+
+ if (is_short)
+ ep_write_UDCCSR(ep, UDCCSR_SP);
+
+ /* requests complete when all IN data is in the FIFO */
+ if (is_last) {
+ completed = 1;
+ break;
+ }
+ } while (!ep_is_full(ep));
+
+ ep_dbg(ep, "wrote count:%d bytes%s%s, left:%d req=%p\n",
+ totcount, is_last ? "/L" : "", is_short ? "/S" : "",
+ req->req.length - req->req.actual, &req->req);
+
+ return completed;
+}
+
+static int read_ep0_fifo(struct pxa_ep *ep, struct pxa27x_request *req)
+{
+ int count, is_short, completed = 0;
+
+ while (epout_has_pkt(ep)) {
+ count = read_packet(ep, req);
+ ep_write_UDCCSR(ep, UDCCSR0_OPC);
+
+ is_short = (count < ep->fifo_size);
+ ep_dbg(ep, "read udccsr:%03x, count:%d bytes%s req %p %d/%d\n",
+ udc_ep_readl(ep, UDCCSR), count, is_short ? "/S" : "",
+ &req->req, req->req.actual, req->req.length);
+
+ if (is_short || req->req.actual >= req->req.length) {
+ completed = 1;
+ break;
+ }
+ }
+
+ return completed;
+}
+
+static int write_ep0_fifo(struct pxa_ep *ep, struct pxa27x_request *req)
+{
+ unsigned count;
+ int is_last, is_short;
+
+ count = write_packet(ep, req, EP0_FIFO_SIZE);
+
+ is_short = (count < EP0_FIFO_SIZE);
+ is_last = ((count == 0) || (count < EP0_FIFO_SIZE));
+
+ /* Sends either a short packet or a 0 length packet */
+ if (unlikely(is_short))
+ ep_write_UDCCSR(ep, UDCCSR0_IPR);
+
+ ep_dbg(ep, "in %d bytes%s%s, %d left, req=%p, udccsr0=0x%03x\n",
+ count, is_short ? "/S" : "", is_last ? "/L" : "",
+ req->req.length - req->req.actual,
+ &req->req, udc_ep_readl(ep, UDCCSR));
+
+ return is_last;
+}
+
+static int pxa_ep_queue(struct usb_ep *_ep, struct usb_request *_req)
+{
+ struct udc_usb_ep *udc_usb_ep;
+ struct pxa_ep *ep;
+ struct pxa27x_request *req;
+ struct pxa_udc *dev;
+ int rc = 0;
+ int is_first_req;
+ unsigned length;
+
+ req = container_of(_req, struct pxa27x_request, req);
+ udc_usb_ep = container_of(_ep, struct udc_usb_ep, usb_ep);
+
+ if (unlikely(!_req || !_req->complete || !_req->buf))
+ return -EINVAL;
+
+ if (unlikely(!_ep))
+ return -EINVAL;
+
+ dev = udc_usb_ep->dev;
+ ep = udc_usb_ep->pxa_ep;
+ if (unlikely(!ep))
+ return -EINVAL;
+
+ dev = ep->dev;
+ if (unlikely(!dev->driver || dev->gadget.speed == USB_SPEED_UNKNOWN)) {
+ ep_dbg(ep, "bogus device state\n");
+ return -ESHUTDOWN;
+ }
+
+ /* iso is always one packet per request, that's the only way
+ * we can report per-packet status. that also helps with dma.
+ */
+ if (unlikely(EPXFERTYPE_is_ISO(ep)
+ && req->req.length > ep->fifo_size))
+ return -EMSGSIZE;
+
+ is_first_req = list_empty(&ep->queue);
+ ep_dbg(ep, "queue req %p(first=%s), len %d buf %p\n",
+ _req, is_first_req ? "yes" : "no",
+ _req->length, _req->buf);
+
+ if (!ep->enabled) {
+ _req->status = -ESHUTDOWN;
+ rc = -ESHUTDOWN;
+ goto out_locked;
+ }
+
+ if (req->in_use) {
+ ep_err(ep, "refusing to queue req %p (already queued)\n", req);
+ goto out_locked;
+ }
+
+ length = _req->length;
+ _req->status = -EINPROGRESS;
+ _req->actual = 0;
+
+ ep_add_request(ep, req);
+
+ if (is_ep0(ep)) {
+ switch (dev->ep0state) {
+ case WAIT_ACK_SET_CONF_INTERF:
+ if (length == 0) {
+ ep_end_in_req(ep, req);
+ } else {
+ ep_err(ep, "got a request of %d bytes while"
+ "in state WAIT_ACK_SET_CONF_INTERF\n",
+ length);
+ ep_del_request(ep, req);
+ rc = -EL2HLT;
+ }
+ ep0_idle(ep->dev);
+ break;
+ case IN_DATA_STAGE:
+ if (!ep_is_full(ep))
+ if (write_ep0_fifo(ep, req))
+ ep0_end_in_req(ep, req);
+ break;
+ case OUT_DATA_STAGE:
+ if ((length == 0) || !epout_has_pkt(ep))
+ if (read_ep0_fifo(ep, req))
+ ep0_end_out_req(ep, req);
+ break;
+ default:
+ ep_err(ep, "odd state %s to send me a request\n",
+ EP0_STNAME(ep->dev));
+ ep_del_request(ep, req);
+ rc = -EL2HLT;
+ break;
+ }
+ } else {
+ handle_ep(ep);
+ }
+
+out:
+ return rc;
+out_locked:
+ goto out;
+}
+
+static int pxa_ep_dequeue(struct usb_ep *_ep, struct usb_request *_req)
+{
+ struct pxa_ep *ep;
+ struct udc_usb_ep *udc_usb_ep;
+ struct pxa27x_request *req;
+ int rc = -EINVAL;
+
+ if (!_ep)
+ return rc;
+ udc_usb_ep = container_of(_ep, struct udc_usb_ep, usb_ep);
+ ep = udc_usb_ep->pxa_ep;
+ if (!ep || is_ep0(ep))
+ return rc;
+
+ /* make sure it's actually queued on this endpoint */
+ list_for_each_entry(req, &ep->queue, queue) {
+ if (&req->req == _req) {
+ rc = 0;
+ break;
+ }
+ }
+
+ if (!rc)
+ req_done(ep, req, -ECONNRESET);
+ return rc;
+}
+
+static int pxa_ep_set_halt(struct usb_ep *_ep, int value)
+{
+ struct pxa_ep *ep;
+ struct udc_usb_ep *udc_usb_ep;
+ int rc;
+
+
+ if (!_ep)
+ return -EINVAL;
+ udc_usb_ep = container_of(_ep, struct udc_usb_ep, usb_ep);
+ ep = udc_usb_ep->pxa_ep;
+ if (!ep || is_ep0(ep))
+ return -EINVAL;
+
+ if (value == 0) {
+ /*
+ * This path (reset toggle+halt) is needed to implement
+ * SET_INTERFACE on normal hardware. but it can't be
+ * done from software on the PXA UDC, and the hardware
+ * forgets to do it as part of SET_INTERFACE automagic.
+ */
+ ep_dbg(ep, "only host can clear halt\n");
+ return -EROFS;
+ }
+
+ rc = -EAGAIN;
+ if (ep->dir_in && (ep_is_full(ep) || !list_empty(&ep->queue)))
+ goto out;
+
+ /* FST, FEF bits are the same for control and non control endpoints */
+ rc = 0;
+ ep_write_UDCCSR(ep, UDCCSR_FST | UDCCSR_FEF);
+ if (is_ep0(ep))
+ set_ep0state(ep->dev, STALL);
+
+out:
+ return rc;
+}
+
+static int pxa_ep_fifo_status(struct usb_ep *_ep)
+{
+ struct pxa_ep *ep;
+ struct udc_usb_ep *udc_usb_ep;
+
+ if (!_ep)
+ return -ENODEV;
+ udc_usb_ep = container_of(_ep, struct udc_usb_ep, usb_ep);
+ ep = udc_usb_ep->pxa_ep;
+ if (!ep || is_ep0(ep))
+ return -ENODEV;
+
+ if (ep->dir_in)
+ return -EOPNOTSUPP;
+ if (ep->dev->gadget.speed == USB_SPEED_UNKNOWN || ep_is_empty(ep))
+ return 0;
+ else
+ return ep_count_bytes_remain(ep) + 1;
+}
+
+static void pxa_ep_fifo_flush(struct usb_ep *_ep)
+{
+ struct pxa_ep *ep;
+ struct udc_usb_ep *udc_usb_ep;
+
+ if (!_ep)
+ return;
+ udc_usb_ep = container_of(_ep, struct udc_usb_ep, usb_ep);
+ ep = udc_usb_ep->pxa_ep;
+ if (!ep || is_ep0(ep))
+ return;
+
+ if (unlikely(!list_empty(&ep->queue)))
+ ep_dbg(ep, "called while queue list not empty\n");
+ ep_dbg(ep, "called\n");
+
+ /* for OUT, just read and discard the FIFO contents. */
+ if (!ep->dir_in) {
+ while (!ep_is_empty(ep))
+ udc_ep_readl(ep, UDCDR);
+ } else {
+ /* most IN status is the same, but ISO can't stall */
+ ep_write_UDCCSR(ep,
+ UDCCSR_PC | UDCCSR_FEF | UDCCSR_TRN
+ | (EPXFERTYPE_is_ISO(ep) ? 0 : UDCCSR_SST));
+ }
+}
+
+static int pxa_ep_enable(struct usb_ep *_ep,
+ const struct usb_endpoint_descriptor *desc)
+{
+ struct pxa_ep *ep;
+ struct udc_usb_ep *udc_usb_ep;
+ struct pxa_udc *udc;
+
+ if (!_ep || !desc)
+ return -EINVAL;
+
+ udc_usb_ep = container_of(_ep, struct udc_usb_ep, usb_ep);
+ if (udc_usb_ep->pxa_ep) {
+ ep = udc_usb_ep->pxa_ep;
+ ep_warn(ep, "usb_ep %s already enabled, doing nothing\n",
+ _ep->name);
+ } else {
+ ep = find_pxa_ep(udc_usb_ep->dev, udc_usb_ep);
+ }
+
+ if (!ep || is_ep0(ep)) {
+ dev_err(udc_usb_ep->dev->dev,
+ "unable to match pxa_ep for ep %s\n",
+ _ep->name);
+ return -EINVAL;
+ }
+
+ if ((desc->bDescriptorType != USB_DT_ENDPOINT)
+ || (ep->type != usb_endpoint_type(desc))) {
+ ep_err(ep, "type mismatch\n");
+ return -EINVAL;
+ }
+
+ if (ep->fifo_size < le16_to_cpu(desc->wMaxPacketSize)) {
+ ep_err(ep, "bad maxpacket\n");
+ return -ERANGE;
+ }
+
+ udc_usb_ep->pxa_ep = ep;
+ udc = ep->dev;
+
+ if (!udc->driver || udc->gadget.speed == USB_SPEED_UNKNOWN) {
+ ep_err(ep, "bogus device state\n");
+ return -ESHUTDOWN;
+ }
+
+ ep->enabled = 1;
+
+ /* flush fifo (mostly for OUT buffers) */
+ pxa_ep_fifo_flush(_ep);
+
+ ep_dbg(ep, "enabled\n");
+ return 0;
+}
+
+static int pxa_ep_disable(struct usb_ep *_ep)
+{
+ struct pxa_ep *ep;
+ struct udc_usb_ep *udc_usb_ep;
+
+ if (!_ep)
+ return -EINVAL;
+
+ udc_usb_ep = container_of(_ep, struct udc_usb_ep, usb_ep);
+ ep = udc_usb_ep->pxa_ep;
+ if (!ep || is_ep0(ep) || !list_empty(&ep->queue))
+ return -EINVAL;
+
+ ep->enabled = 0;
+ nuke(ep, -ESHUTDOWN);
+
+ pxa_ep_fifo_flush(_ep);
+ udc_usb_ep->pxa_ep = NULL;
+
+ ep_dbg(ep, "disabled\n");
+ return 0;
+}
+
+static struct usb_ep_ops pxa_ep_ops = {
+ .enable = pxa_ep_enable,
+ .disable = pxa_ep_disable,
+
+ .alloc_request = pxa_ep_alloc_request,
+ .free_request = pxa_ep_free_request,
+
+ .queue = pxa_ep_queue,
+ .dequeue = pxa_ep_dequeue,
+
+ .set_halt = pxa_ep_set_halt,
+ .fifo_status = pxa_ep_fifo_status,
+ .fifo_flush = pxa_ep_fifo_flush,
+};
+
+static void dplus_pullup(struct pxa_udc *udc, int on)
+{
+ if (on) {
+ if (udc->mach->gpio_pullup > 0)
+ gpio_set_value(udc->mach->gpio_pullup,
+ !udc->mach->gpio_pullup_inverted);
+ if (udc->mach->udc_command)
+ udc->mach->udc_command(PXA2XX_UDC_CMD_CONNECT);
+ } else {
+ if (udc->mach->gpio_pullup > 0)
+ gpio_set_value(udc->mach->gpio_pullup,
+ udc->mach->gpio_pullup_inverted);
+ if (udc->mach->udc_command)
+ udc->mach->udc_command(PXA2XX_UDC_CMD_DISCONNECT);
+ }
+ udc->pullup_on = on;
+}
+
+/**
+ * pxa_udc_get_frame - Returns usb frame number
+ * @_gadget: usb gadget
+ */
+static int pxa_udc_get_frame(struct usb_gadget *_gadget)
+{
+ struct pxa_udc *udc = to_gadget_udc(_gadget);
+
+ return udc_readl(udc, UDCFNR) & 0x7ff;
+}
+
+static int pxa_udc_wakeup(struct usb_gadget *_gadget)
+{
+ struct pxa_udc *udc = to_gadget_udc(_gadget);
+
+ /* host may not have enabled remote wakeup */
+ if ((udc_readl(udc, UDCCR) & UDCCR_DWRE) == 0)
+ return -EHOSTUNREACH;
+ udc_set_mask_UDCCR(udc, UDCCR_UDR);
+ return 0;
+}
+
+static void udc_enable(struct pxa_udc *udc);
+static void udc_disable(struct pxa_udc *udc);
+
+static int should_enable_udc(struct pxa_udc *udc)
+{
+ int put_on;
+
+ put_on = ((udc->pullup_on) && (udc->driver));
+ put_on &= udc->vbus_sensed;
+ return put_on;
+}
+
+static int should_disable_udc(struct pxa_udc *udc)
+{
+ int put_off;
+
+ put_off = ((!udc->pullup_on) || (!udc->driver));
+ put_off |= !udc->vbus_sensed;
+ return put_off;
+}
+
+static int pxa_udc_pullup(struct usb_gadget *_gadget, int is_active)
+{
+ struct pxa_udc *udc = to_gadget_udc(_gadget);
+
+ if ((udc->mach->gpio_pullup < 0) && !udc->mach->udc_command)
+ return -EOPNOTSUPP;
+
+ dplus_pullup(udc, is_active);
+
+ if (should_enable_udc(udc))
+ udc_enable(udc);
+ if (should_disable_udc(udc))
+ udc_disable(udc);
+ return 0;
+}
+
+static int pxa_udc_vbus_session(struct usb_gadget *_gadget, int is_active)
+{
+ struct pxa_udc *udc = to_gadget_udc(_gadget);
+
+ udc->vbus_sensed = is_active;
+ if (should_enable_udc(udc))
+ udc_enable(udc);
+ if (should_disable_udc(udc))
+ udc_disable(udc);
+
+ return 0;
+}
+
+static const struct usb_gadget_ops pxa_udc_ops = {
+ .get_frame = pxa_udc_get_frame,
+ .wakeup = pxa_udc_wakeup,
+ .pullup = pxa_udc_pullup,
+ .vbus_session = pxa_udc_vbus_session,
+};
+
+static void clk_enable(void)
+{
+ CKEN |= CKEN_USB;
+}
+
+static void clk_disable(void)
+{
+ CKEN &= ~CKEN_USB;
+}
+
+static void udc_disable(struct pxa_udc *udc)
+{
+ if (!udc->enabled)
+ return;
+
+ udc_writel(udc, UDCICR0, 0);
+ udc_writel(udc, UDCICR1, 0);
+
+ udc_clear_mask_UDCCR(udc, UDCCR_UDE);
+ clk_disable();
+
+ ep0_idle(udc);
+ udc->gadget.speed = USB_SPEED_UNKNOWN;
+
+ udc->enabled = 0;
+}
+
+static __init void udc_init_data(struct pxa_udc *dev)
+{
+ int i;
+ struct pxa_ep *ep;
+
+ /* device/ep0 records init */
+ INIT_LIST_HEAD(&dev->gadget.ep_list);
+ INIT_LIST_HEAD(&dev->gadget.ep0->ep_list);
+ dev->udc_usb_ep[0].pxa_ep = &dev->pxa_ep[0];
+ ep0_idle(dev);
+
+ /* PXA endpoints init */
+ for (i = 0; i < NR_PXA_ENDPOINTS; i++) {
+ ep = &dev->pxa_ep[i];
+
+ ep->enabled = is_ep0(ep);
+ INIT_LIST_HEAD(&ep->queue);
+ }
+
+ /* USB endpoints init */
+ for (i = 1; i < NR_USB_ENDPOINTS; i++)
+ list_add_tail(&dev->udc_usb_ep[i].usb_ep.ep_list,
+ &dev->gadget.ep_list);
+}
+
+static void udc_enable(struct pxa_udc *udc)
+{
+ if (udc->enabled)
+ return;
+
+ udc_writel(udc, UDCICR0, 0);
+ udc_writel(udc, UDCICR1, 0);
+ udc_clear_mask_UDCCR(udc, UDCCR_UDE);
+
+ clk_enable();
+
+ ep0_idle(udc);
+ udc->gadget.speed = USB_SPEED_FULL;
+ memset(&udc->stats, 0, sizeof(udc->stats));
+
+ udc_set_mask_UDCCR(udc, UDCCR_UDE);
+ ep_write_UDCCSR(&udc->pxa_ep[0], UDCCSR0_ACM);
+ udelay(2);
+ if (udc_readl(udc, UDCCR) & UDCCR_EMCE)
+ dev_err(udc->dev, "Configuration errors, udc disabled\n");
+
+ /*
+ * Caller must be able to sleep in order to cope with startup transients
+ */
+ mdelay(100);
+
+ /* enable suspend/resume and reset irqs */
+ udc_writel(udc, UDCICR1,
+ UDCICR1_IECC | UDCICR1_IERU
+ | UDCICR1_IESU | UDCICR1_IERS);
+
+ pio_irq_enable(&udc->pxa_ep[0]);
+ udc->enabled = 1;
+}
+
+int usb_gadget_register_driver(struct usb_gadget_driver *driver)
+{
+ struct pxa_udc *udc = the_controller;
+ int retval;
+
+ if (!driver || driver->speed < USB_SPEED_FULL || !driver->bind
+ || !driver->disconnect || !driver->setup)
+ return -EINVAL;
+ if (!udc)
+ return -ENODEV;
+ if (udc->driver)
+ return -EBUSY;
+
+ /* first hook up the driver ... */
+ udc->driver = driver;
+ dplus_pullup(udc, 1);
+
+ retval = driver->bind(&udc->gadget);
+ if (retval) {
+ dev_err(udc->dev, "bind to function %s --> error %d\n",
+ driver->function, retval);
+ goto bind_fail;
+ }
+ dev_dbg(udc->dev, "registered gadget function '%s'\n",
+ driver->function);
+
+ if (should_enable_udc(udc))
+ udc_enable(udc);
+ return 0;
+
+bind_fail:
+ return retval;
+}
+EXPORT_SYMBOL(usb_gadget_register_driver);
+
+static void stop_activity(struct pxa_udc *udc, struct usb_gadget_driver *driver)
+{
+ int i;
+
+ /* don't disconnect drivers more than once */
+ if (udc->gadget.speed == USB_SPEED_UNKNOWN)
+ driver = NULL;
+ udc->gadget.speed = USB_SPEED_UNKNOWN;
+
+ for (i = 0; i < NR_USB_ENDPOINTS; i++)
+ pxa_ep_disable(&udc->udc_usb_ep[i].usb_ep);
+
+ if (driver)
+ driver->disconnect(&udc->gadget);
+}
+
+int usb_gadget_unregister_driver(struct usb_gadget_driver *driver)
+{
+ struct pxa_udc *udc = the_controller;
+
+ if (!udc)
+ return -ENODEV;
+ if (!driver || driver != udc->driver || !driver->unbind)
+ return -EINVAL;
+
+ stop_activity(udc, driver);
+ udc_disable(udc);
+ dplus_pullup(udc, 0);
+
+ driver->disconnect(&udc->gadget);
+ driver->unbind(&udc->gadget);
+ udc->driver = NULL;
+
+ /*
+ dev_info(udc->dev, "unregistered gadget driver '%s'\n",
+ driver->driver.name);
+ */
+ return 0;
+}
+EXPORT_SYMBOL(usb_gadget_unregister_driver);
+
+static void handle_ep0_ctrl_req(struct pxa_udc *udc,
+ struct pxa27x_request *req)
+{
+ struct pxa_ep *ep = &udc->pxa_ep[0];
+ union {
+ struct usb_ctrlrequest r;
+ u32 word[2];
+ } u;
+ int i;
+ int have_extrabytes = 0;
+
+ nuke(ep, -EPROTO);
+
+ /*
+ * In the PXA320 manual, in the section about Back-to-Back setup
+ * packets, it describes this situation. The solution is to set OPC to
+ * get rid of the status packet, and then continue with the setup
+ * packet. Generalize to pxa27x CPUs.
+ */
+ if (epout_has_pkt(ep) && (ep_count_bytes_remain(ep) == 0))
+ ep_write_UDCCSR(ep, UDCCSR0_OPC);
+
+ /* read SETUP packet */
+ for (i = 0; i < 2; i++) {
+ if (unlikely(ep_is_empty(ep)))
+ goto stall;
+ u.word[i] = udc_ep_readl(ep, UDCDR);
+ }
+
+ have_extrabytes = !ep_is_empty(ep);
+ while (!ep_is_empty(ep)) {
+ i = udc_ep_readl(ep, UDCDR);
+ ep_err(ep, "wrong to have extra bytes for setup : 0x%08x\n", i);
+ }
+
+ ep_dbg(ep, "SETUP %02x.%02x v%04x i%04x l%04x\n",
+ u.r.bRequestType, u.r.bRequest,
+ le16_to_cpu(u.r.wValue), le16_to_cpu(u.r.wIndex),
+ le16_to_cpu(u.r.wLength));
+ if (unlikely(have_extrabytes))
+ goto stall;
+
+ if (u.r.bRequestType & USB_DIR_IN)
+ set_ep0state(udc, IN_DATA_STAGE);
+ else
+ set_ep0state(udc, OUT_DATA_STAGE);
+
+ /* Tell UDC to enter Data Stage */
+ ep_write_UDCCSR(ep, UDCCSR0_SA | UDCCSR0_OPC);
+
+ i = udc->driver->setup(&udc->gadget, &u.r);
+ if (i < 0)
+ goto stall;
+out:
+ return;
+stall:
+ ep_dbg(ep, "protocol STALL, udccsr0=%03x err %d\n",
+ udc_ep_readl(ep, UDCCSR), i);
+ ep_write_UDCCSR(ep, UDCCSR0_FST | UDCCSR0_FTF);
+ set_ep0state(udc, STALL);
+ goto out;
+}
+
+static void handle_ep0(struct pxa_udc *udc, int fifo_irq, int opc_irq)
+{
+ u32 udccsr0;
+ struct pxa_ep *ep = &udc->pxa_ep[0];
+ struct pxa27x_request *req = NULL;
+ int completed = 0;
+
+ if (!list_empty(&ep->queue))
+ req = list_entry(ep->queue.next, struct pxa27x_request, queue);
+
+ udccsr0 = udc_ep_readl(ep, UDCCSR);
+ ep_dbg(ep, "state=%s, req=%p, udccsr0=0x%03x, udcbcr=%d, irq_msk=%x\n",
+ EP0_STNAME(udc), req, udccsr0, udc_ep_readl(ep, UDCBCR),
+ (fifo_irq << 1 | opc_irq));
+
+ if (udccsr0 & UDCCSR0_SST) {
+ ep_dbg(ep, "clearing stall status\n");
+ nuke(ep, -EPIPE);
+ ep_write_UDCCSR(ep, UDCCSR0_SST);
+ ep0_idle(udc);
+ }
+
+ if (udccsr0 & UDCCSR0_SA) {
+ nuke(ep, 0);
+ set_ep0state(udc, SETUP_STAGE);
+ }
+
+ switch (udc->ep0state) {
+ case WAIT_FOR_SETUP:
+ /*
+ * Hardware bug : beware, we cannot clear OPC, since we would
+ * miss a potential OPC irq for a setup packet.
+ * So, we only do ... nothing, and hope for a next irq with
+ * UDCCSR0_SA set.
+ */
+ break;
+ case SETUP_STAGE:
+ udccsr0 &= UDCCSR0_CTRL_REQ_MASK;
+ if (likely(udccsr0 == UDCCSR0_CTRL_REQ_MASK))
+ handle_ep0_ctrl_req(udc, req);
+ break;
+ case IN_DATA_STAGE: /* GET_DESCRIPTOR */
+ if (epout_has_pkt(ep))
+ ep_write_UDCCSR(ep, UDCCSR0_OPC);
+ if (req && !ep_is_full(ep))
+ completed = write_ep0_fifo(ep, req);
+ if (completed)
+ ep0_end_in_req(ep, req);
+ break;
+ case OUT_DATA_STAGE: /* SET_DESCRIPTOR */
+ if (epout_has_pkt(ep) && req)
+ completed = read_ep0_fifo(ep, req);
+ if (completed)
+ ep0_end_out_req(ep, req);
+ break;
+ case STALL:
+ ep_write_UDCCSR(ep, UDCCSR0_FST);
+ break;
+ case IN_STATUS_STAGE:
+ /*
+ * Hardware bug : beware, we cannot clear OPC, since we would
+ * miss a potential PC irq for a setup packet.
+ * So, we only put the ep0 into WAIT_FOR_SETUP state.
+ */
+ if (opc_irq)
+ ep0_idle(udc);
+ break;
+ case OUT_STATUS_STAGE:
+ case WAIT_ACK_SET_CONF_INTERF:
+ ep_warn(ep, "should never get in %s state here!!!\n",
+ EP0_STNAME(ep->dev));
+ ep0_idle(udc);
+ break;
+ }
+}
+
+static void handle_ep(struct pxa_ep *ep)
+{
+ struct pxa27x_request *req;
+ int completed;
+ u32 udccsr;
+ int is_in = ep->dir_in;
+ int loop = 0;
+
+ do {
+ completed = 0;
+ udccsr = udc_ep_readl(ep, UDCCSR);
+
+ if (likely(!list_empty(&ep->queue)))
+ req = list_entry(ep->queue.next,
+ struct pxa27x_request, queue);
+ else
+ req = NULL;
+
+ ep_dbg(ep, "req:%p, udccsr 0x%03x loop=%d\n",
+ req, udccsr, loop++);
+
+ if (unlikely(udccsr & (UDCCSR_SST | UDCCSR_TRN)))
+ udc_ep_writel(ep, UDCCSR,
+ udccsr & (UDCCSR_SST | UDCCSR_TRN));
+ if (!req)
+ break;
+
+ if (unlikely(is_in)) {
+ if (likely(!ep_is_full(ep)))
+ completed = write_fifo(ep, req);
+ } else {
+ if (likely(epout_has_pkt(ep)))
+ completed = read_fifo(ep, req);
+ }
+
+ if (completed) {
+ if (is_in)
+ ep_end_in_req(ep, req);
+ else
+ ep_end_out_req(ep, req);
+ }
+ } while (completed);
+
+ return;
+}
+
+static void pxa27x_change_configuration(struct pxa_udc *udc, int config)
+{
+ struct usb_ctrlrequest req ;
+
+ dev_dbg(udc->dev, "config=%d\n", config);
+
+ udc->config = config;
+ udc->last_interface = 0;
+ udc->last_alternate = 0;
+
+ req.bRequestType = 0;
+ req.bRequest = USB_REQ_SET_CONFIGURATION;
+ req.wValue = config;
+ req.wIndex = 0;
+ req.wLength = 0;
+
+ set_ep0state(udc, WAIT_ACK_SET_CONF_INTERF);
+ udc->driver->setup(&udc->gadget, &req);
+}
+
+static void pxa27x_change_interface(struct pxa_udc *udc, int iface, int alt)
+{
+ struct usb_ctrlrequest req;
+
+ dev_dbg(udc->dev, "interface=%d, alternate setting=%d\n", iface, alt);
+
+ udc->last_interface = iface;
+ udc->last_alternate = alt;
+
+ req.bRequestType = USB_RECIP_INTERFACE;
+ req.bRequest = USB_REQ_SET_INTERFACE;
+ req.wValue = alt;
+ req.wIndex = iface;
+ req.wLength = 0;
+
+ set_ep0state(udc, WAIT_ACK_SET_CONF_INTERF);
+ ep_write_UDCCSR(&udc->pxa_ep[0], UDCCSR0_AREN);
+ udc->driver->setup(&udc->gadget, &req);
+}
+
+static void irq_handle_data(struct pxa_udc *udc)
+{
+ int i;
+ struct pxa_ep *ep;
+ u32 udcisr0 = udc_readl(udc, UDCISR0) & UDCCISR0_EP_MASK;
+ u32 udcisr1 = udc_readl(udc, UDCISR1) & UDCCISR1_EP_MASK;
+
+ if (udcisr0 & UDCISR_INT_MASK) {
+ udc_writel(udc, UDCISR0, UDCISR_INT(0, UDCISR_INT_MASK));
+ handle_ep0(udc, !!(udcisr0 & UDCICR_FIFOERR),
+ !!(udcisr0 & UDCICR_PKTCOMPL));
+ }
+
+ udcisr0 >>= 2;
+ for (i = 1; udcisr0 != 0 && i < 16; udcisr0 >>= 2, i++) {
+ if (!(udcisr0 & UDCISR_INT_MASK))
+ continue;
+
+ udc_writel(udc, UDCISR0, UDCISR_INT(i, UDCISR_INT_MASK));
+
+ WARN_ON(i >= ARRAY_SIZE(udc->pxa_ep));
+ if (i < ARRAY_SIZE(udc->pxa_ep)) {
+ ep = &udc->pxa_ep[i];
+ if (ep->enabled)
+ handle_ep(ep);
+ }
+ }
+
+ for (i = 16; udcisr1 != 0 && i < 24; udcisr1 >>= 2, i++) {
+ udc_writel(udc, UDCISR1, UDCISR_INT(i - 16, UDCISR_INT_MASK));
+ if (!(udcisr1 & UDCISR_INT_MASK))
+ continue;
+
+ WARN_ON(i >= ARRAY_SIZE(udc->pxa_ep));
+ if (i < ARRAY_SIZE(udc->pxa_ep)) {
+ ep = &udc->pxa_ep[i];
+ if (ep->enabled)
+ handle_ep(ep);
+ }
+ }
+
+}
+
+static void irq_udc_suspend(struct pxa_udc *udc)
+{
+ udc_writel(udc, UDCISR1, UDCISR1_IRSU);
+
+ if (udc->gadget.speed != USB_SPEED_UNKNOWN
+ && udc->driver && udc->driver->suspend)
+ udc->driver->suspend(&udc->gadget);
+ ep0_idle(udc);
+}
+
+static void irq_udc_resume(struct pxa_udc *udc)
+{
+ udc_writel(udc, UDCISR1, UDCISR1_IRRU);
+
+ if (udc->gadget.speed != USB_SPEED_UNKNOWN
+ && udc->driver && udc->driver->resume)
+ udc->driver->resume(&udc->gadget);
+}
+
+static void irq_udc_reconfig(struct pxa_udc *udc)
+{
+ unsigned config, interface, alternate, config_change;
+ u32 udccr = udc_readl(udc, UDCCR);
+
+ udc_writel(udc, UDCISR1, UDCISR1_IRCC);
+
+ config = (udccr & UDCCR_ACN) >> UDCCR_ACN_S;
+ config_change = (config != udc->config);
+ if (config_change)
+ update_pxa_ep_matches(udc);
+ udc_set_mask_UDCCR(udc, UDCCR_SMAC);
+ ep_write_UDCCSR(&udc->pxa_ep[0], UDCCSR0_AREN);
+
+ pxa27x_change_configuration(udc, config);
+ interface = (udccr & UDCCR_AIN) >> UDCCR_AIN_S;
+ alternate = (udccr & UDCCR_AAISN) >> UDCCR_AAISN_S;
+
+ /*
+ * barebox specific: do not call change interface, as change_config has
+ * already setup the gadget.
+ * pxa27x_change_interface(udc, interface, alternate);
+ */
+}
+
+static void irq_udc_reset(struct pxa_udc *udc)
+{
+ u32 udccr = udc_readl(udc, UDCCR);
+ struct pxa_ep *ep = &udc->pxa_ep[0];
+
+ dev_info(udc->dev, "USB reset\n");
+ udc_writel(udc, UDCISR1, UDCISR1_IRRS);
+
+ if ((udccr & UDCCR_UDA) == 0) {
+ dev_dbg(udc->dev, "USB reset start\n");
+ stop_activity(udc, udc->driver);
+ }
+ udc->gadget.speed = USB_SPEED_FULL;
+
+ nuke(ep, -EPROTO);
+ ep_write_UDCCSR(ep, UDCCSR0_FTF | UDCCSR0_OPC);
+ ep0_idle(udc);
+}
+
+int usb_gadget_poll(void)
+{
+ struct pxa_udc *udc = the_controller;
+ u32 udcisr0 = udc_readl(udc, UDCISR0);
+ u32 udcisr1 = udc_readl(udc, UDCISR1);
+ u32 udccr = udc_readl(udc, UDCCR);
+ u32 udcisr1_spec;
+ int ret = 0;
+
+ udc->vbus_sensed = udc->mach->udc_is_connected();
+ if (should_enable_udc(udc))
+ udc_enable(udc);
+ if (should_disable_udc(udc)) {
+ stop_activity(udc, udc->driver);
+ udc_disable(udc);
+ }
+
+ if (!udc->enabled)
+ return -EIO;
+
+ dev_dbg(udc->dev, "Interrupt, UDCISR0:0x%08x, UDCISR1:0x%08x, "
+ "UDCCR:0x%08x\n", udcisr0, udcisr1, udccr);
+
+ udcisr1_spec = udcisr1 & 0xf8000000;
+ if (unlikely(udcisr1_spec & UDCISR1_IRSU))
+ irq_udc_suspend(udc);
+ if (unlikely(udcisr1_spec & UDCISR1_IRRU))
+ irq_udc_resume(udc);
+ if (unlikely(udcisr1_spec & UDCISR1_IRCC))
+ irq_udc_reconfig(udc);
+ if (unlikely(udcisr1_spec & UDCISR1_IRRS))
+ irq_udc_reset(udc);
+ if (udcisr1_spec)
+ ret = 1;
+
+ if ((udcisr0 & UDCCISR0_EP_MASK) | (udcisr1 & UDCCISR1_EP_MASK)) {
+ irq_handle_data(udc);
+ ret = 1;
+ }
+
+ return ret;
+}
+
+static struct pxa_udc memory = {
+ .gadget = {
+ .ops = &pxa_udc_ops,
+ .ep0 = &memory.udc_usb_ep[0].usb_ep,
+ .name = driver_name,
+ },
+
+ .udc_usb_ep = {
+ USB_EP_CTRL,
+ USB_EP_OUT_BULK(1),
+ USB_EP_IN_BULK(2),
+ USB_EP_IN_ISO(3),
+ USB_EP_OUT_ISO(4),
+ USB_EP_IN_INT(5),
+ },
+
+ .pxa_ep = {
+ PXA_EP_CTRL,
+ /* Endpoints for gadget zero */
+ PXA_EP_OUT_BULK(1, 1, 3, 0, 0),
+ PXA_EP_IN_BULK(2, 2, 3, 0, 0),
+ /* Endpoints for ether gadget, file storage gadget */
+ PXA_EP_OUT_BULK(3, 1, 1, 0, 0),
+ PXA_EP_IN_BULK(4, 2, 1, 0, 0),
+ PXA_EP_IN_ISO(5, 3, 1, 0, 0),
+ PXA_EP_OUT_ISO(6, 4, 1, 0, 0),
+ PXA_EP_IN_INT(7, 5, 1, 0, 0),
+ /* Endpoints for RNDIS, serial */
+ PXA_EP_OUT_BULK(8, 1, 2, 0, 0),
+ PXA_EP_IN_BULK(9, 2, 2, 0, 0),
+ PXA_EP_IN_INT(10, 5, 2, 0, 0),
+ /*
+ * All the following endpoints are only for completion. They
+ * won't never work, as multiple interfaces are really broken on
+ * the pxa.
+ */
+ PXA_EP_OUT_BULK(11, 1, 2, 1, 0),
+ PXA_EP_IN_BULK(12, 2, 2, 1, 0),
+ /* Endpoint for CDC Ether */
+ PXA_EP_OUT_BULK(13, 1, 1, 1, 1),
+ PXA_EP_IN_BULK(14, 2, 1, 1, 1),
+ }
+};
+
+static int __init pxa_udc_probe(struct device_d *dev)
+{
+ struct pxa_udc *udc = &memory;
+ int gpio;
+
+ udc->regs = dev_request_mem_region(dev, 0);
+ if (!udc->regs)
+ return -ENXIO;
+
+ udc->dev = dev;
+ udc->mach = dev->platform_data;
+
+ gpio = udc->mach->gpio_pullup;
+ if (gpio >= 0) {
+ gpio_direction_output(gpio,
+ udc->mach->gpio_pullup_inverted);
+ }
+
+ udc->vbus_sensed = 0;
+
+ the_controller = udc;
+ udc_init_data(udc);
+ pxa_eps_setup(udc);
+ return 0;
+}
+
+#define pxa27x_clear_otgph() do {} while (0)
+
+static struct driver_d udc_driver = {
+ .name = "pxa27x-udc",
+ .probe = pxa_udc_probe,
+};
+
+static int pxa27x_udc_poller(struct poller_struct *poller)
+{
+ return usb_gadget_poll();
+}
+static struct poller_struct poller = {
+ .func = pxa27x_udc_poller
+};
+
+static int __init pxa27x_udc_init(void)
+{
+ register_driver(&udc_driver);
+ poller_register(&poller);
+ return 0;
+}
+
+device_initcall(pxa27x_udc_init);
diff --git a/drivers/usb/gadget/pxa27x_udc.h b/drivers/usb/gadget/pxa27x_udc.h
new file mode 100644
index 0000000..eace2e4
--- /dev/null
+++ b/drivers/usb/gadget/pxa27x_udc.h
@@ -0,0 +1,393 @@
+/*
+ * linux/drivers/usb/gadget/pxa27x_udc.h
+ * Intel PXA27x on-chip full speed USB device controller
+ *
+ * Inspired by original driver by Frank Becker, David Brownell, and others.
+ * Copyright (C) 2008 Robert Jarzmik
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ * Taken from linux-2.6 kernel and adapted to barebox.
+ */
+
+#ifndef __LINUX_USB_GADGET_PXA27X_H
+#define __LINUX_USB_GADGET_PXA27X_H
+
+/*
+ * Register definitions
+ */
+/* Offsets */
+#define UDCCR 0x0000 /* UDC Control Register */
+#define UDCICR0 0x0004 /* UDC Interrupt Control Register0 */
+#define UDCICR1 0x0008 /* UDC Interrupt Control Register1 */
+#define UDCISR0 0x000C /* UDC Interrupt Status Register 0 */
+#define UDCISR1 0x0010 /* UDC Interrupt Status Register 1 */
+#define UDCFNR 0x0014 /* UDC Frame Number Register */
+#define UDCOTGICR 0x0018 /* UDC On-The-Go interrupt control */
+#define UP2OCR 0x0020 /* USB Port 2 Output Control register */
+#define UP3OCR 0x0024 /* USB Port 3 Output Control register */
+#define UDCCSRn(x) (0x0100 + ((x)<<2)) /* UDC Control/Status register */
+#define UDCBCRn(x) (0x0200 + ((x)<<2)) /* UDC Byte Count Register */
+#define UDCDRn(x) (0x0300 + ((x)<<2)) /* UDC Data Register */
+#define UDCCRn(x) (0x0400 + ((x)<<2)) /* UDC Control Register */
+
+#define UDCCR_OEN (1 << 31) /* On-the-Go Enable */
+#define UDCCR_AALTHNP (1 << 30) /* A-device Alternate Host Negotiation
+ Protocol Port Support */
+#define UDCCR_AHNP (1 << 29) /* A-device Host Negotiation Protocol
+ Support */
+#define UDCCR_BHNP (1 << 28) /* B-device Host Negotiation Protocol
+ Enable */
+#define UDCCR_DWRE (1 << 16) /* Device Remote Wake-up Enable */
+#define UDCCR_ACN (0x03 << 11) /* Active UDC configuration Number */
+#define UDCCR_ACN_S 11
+#define UDCCR_AIN (0x07 << 8) /* Active UDC interface Number */
+#define UDCCR_AIN_S 8
+#define UDCCR_AAISN (0x07 << 5) /* Active UDC Alternate Interface
+ Setting Number */
+#define UDCCR_AAISN_S 5
+#define UDCCR_SMAC (1 << 4) /* Switch Endpoint Memory to Active
+ Configuration */
+#define UDCCR_EMCE (1 << 3) /* Endpoint Memory Configuration
+ Error */
+#define UDCCR_UDR (1 << 2) /* UDC Resume */
+#define UDCCR_UDA (1 << 1) /* UDC Active */
+#define UDCCR_UDE (1 << 0) /* UDC Enable */
+
+#define UDCICR_INT(n, intr) (((intr) & 0x03) << (((n) & 0x0F) * 2))
+#define UDCICR1_IECC (1 << 31) /* IntEn - Configuration Change */
+#define UDCICR1_IESOF (1 << 30) /* IntEn - Start of Frame */
+#define UDCICR1_IERU (1 << 29) /* IntEn - Resume */
+#define UDCICR1_IESU (1 << 28) /* IntEn - Suspend */
+#define UDCICR1_IERS (1 << 27) /* IntEn - Reset */
+#define UDCICR_FIFOERR (1 << 1) /* FIFO Error interrupt for EP */
+#define UDCICR_PKTCOMPL (1 << 0) /* Packet Complete interrupt for EP */
+#define UDCICR_INT_MASK (UDCICR_FIFOERR | UDCICR_PKTCOMPL)
+
+#define UDCISR_INT(n, intr) (((intr) & 0x03) << (((n) & 0x0F) * 2))
+#define UDCISR1_IRCC (1 << 31) /* IntReq - Configuration Change */
+#define UDCISR1_IRSOF (1 << 30) /* IntReq - Start of Frame */
+#define UDCISR1_IRRU (1 << 29) /* IntReq - Resume */
+#define UDCISR1_IRSU (1 << 28) /* IntReq - Suspend */
+#define UDCISR1_IRRS (1 << 27) /* IntReq - Reset */
+#define UDCISR_INT_MASK (UDCICR_FIFOERR | UDCICR_PKTCOMPL)
+
+#define UDCOTGICR_IESF (1 << 24) /* OTG SET_FEATURE command recvd */
+#define UDCOTGICR_IEXR (1 << 17) /* Extra Transceiver Interrupt
+ Rising Edge Interrupt Enable */
+#define UDCOTGICR_IEXF (1 << 16) /* Extra Transceiver Interrupt
+ Falling Edge Interrupt Enable */
+#define UDCOTGICR_IEVV40R (1 << 9) /* OTG Vbus Valid 4.0V Rising Edge
+ Interrupt Enable */
+#define UDCOTGICR_IEVV40F (1 << 8) /* OTG Vbus Valid 4.0V Falling Edge
+ Interrupt Enable */
+#define UDCOTGICR_IEVV44R (1 << 7) /* OTG Vbus Valid 4.4V Rising Edge
+ Interrupt Enable */
+#define UDCOTGICR_IEVV44F (1 << 6) /* OTG Vbus Valid 4.4V Falling Edge
+ Interrupt Enable */
+#define UDCOTGICR_IESVR (1 << 5) /* OTG Session Valid Rising Edge
+ Interrupt Enable */
+#define UDCOTGICR_IESVF (1 << 4) /* OTG Session Valid Falling Edge
+ Interrupt Enable */
+#define UDCOTGICR_IESDR (1 << 3) /* OTG A-Device SRP Detect Rising
+ Edge Interrupt Enable */
+#define UDCOTGICR_IESDF (1 << 2) /* OTG A-Device SRP Detect Falling
+ Edge Interrupt Enable */
+#define UDCOTGICR_IEIDR (1 << 1) /* OTG ID Change Rising Edge
+ Interrupt Enable */
+#define UDCOTGICR_IEIDF (1 << 0) /* OTG ID Change Falling Edge
+ Interrupt Enable */
+
+/* Host Port 2 field bits */
+#define UP2OCR_CPVEN (1 << 0) /* Charge Pump Vbus Enable */
+#define UP2OCR_CPVPE (1 << 1) /* Charge Pump Vbus Pulse Enable */
+ /* Transceiver enablers */
+#define UP2OCR_DPPDE (1 << 2) /* D+ Pull Down Enable */
+#define UP2OCR_DMPDE (1 << 3) /* D- Pull Down Enable */
+#define UP2OCR_DPPUE (1 << 4) /* D+ Pull Up Enable */
+#define UP2OCR_DMPUE (1 << 5) /* D- Pull Up Enable */
+#define UP2OCR_DPPUBE (1 << 6) /* D+ Pull Up Bypass Enable */
+#define UP2OCR_DMPUBE (1 << 7) /* D- Pull Up Bypass Enable */
+#define UP2OCR_EXSP (1 << 8) /* External Transceiver Speed Control */
+#define UP2OCR_EXSUS (1 << 9) /* External Transceiver Speed Enable */
+#define UP2OCR_IDON (1 << 10) /* OTG ID Read Enable */
+#define UP2OCR_HXS (1 << 16) /* Transceiver Output Select */
+#define UP2OCR_HXOE (1 << 17) /* Transceiver Output Enable */
+#define UP2OCR_SEOS (1 << 24) /* Single-Ended Output Select */
+
+#define UDCCSR0_ACM (1 << 9) /* Ack Control Mode */
+#define UDCCSR0_AREN (1 << 8) /* Ack Response Enable */
+#define UDCCSR0_SA (1 << 7) /* Setup Active */
+#define UDCCSR0_RNE (1 << 6) /* Receive FIFO Not Empty */
+#define UDCCSR0_FST (1 << 5) /* Force Stall */
+#define UDCCSR0_SST (1 << 4) /* Sent Stall */
+#define UDCCSR0_DME (1 << 3) /* DMA Enable */
+#define UDCCSR0_FTF (1 << 2) /* Flush Transmit FIFO */
+#define UDCCSR0_IPR (1 << 1) /* IN Packet Ready */
+#define UDCCSR0_OPC (1 << 0) /* OUT Packet Complete */
+
+#define UDCCSR_DPE (1 << 9) /* Data Packet Error */
+#define UDCCSR_FEF (1 << 8) /* Flush Endpoint FIFO */
+#define UDCCSR_SP (1 << 7) /* Short Packet Control/Status */
+#define UDCCSR_BNE (1 << 6) /* Buffer Not Empty (IN endpoints) */
+#define UDCCSR_BNF (1 << 6) /* Buffer Not Full (OUT endpoints) */
+#define UDCCSR_FST (1 << 5) /* Force STALL */
+#define UDCCSR_SST (1 << 4) /* Sent STALL */
+#define UDCCSR_DME (1 << 3) /* DMA Enable */
+#define UDCCSR_TRN (1 << 2) /* Tx/Rx NAK */
+#define UDCCSR_PC (1 << 1) /* Packet Complete */
+#define UDCCSR_FS (1 << 0) /* FIFO needs service */
+
+#define UDCCONR_CN (0x03 << 25) /* Configuration Number */
+#define UDCCONR_CN_S 25
+#define UDCCONR_IN (0x07 << 22) /* Interface Number */
+#define UDCCONR_IN_S 22
+#define UDCCONR_AISN (0x07 << 19) /* Alternate Interface Number */
+#define UDCCONR_AISN_S 19
+#define UDCCONR_EN (0x0f << 15) /* Endpoint Number */
+#define UDCCONR_EN_S 15
+#define UDCCONR_ET (0x03 << 13) /* Endpoint Type: */
+#define UDCCONR_ET_S 13
+#define UDCCONR_ET_INT (0x03 << 13) /* Interrupt */
+#define UDCCONR_ET_BULK (0x02 << 13) /* Bulk */
+#define UDCCONR_ET_ISO (0x01 << 13) /* Isochronous */
+#define UDCCONR_ET_NU (0x00 << 13) /* Not used */
+#define UDCCONR_ED (1 << 12) /* Endpoint Direction */
+#define UDCCONR_MPS (0x3ff << 2) /* Maximum Packet Size */
+#define UDCCONR_MPS_S 2
+#define UDCCONR_DE (1 << 1) /* Double Buffering Enable */
+#define UDCCONR_EE (1 << 0) /* Endpoint Enable */
+
+#define UDCCR_MASK_BITS (UDCCR_OEN | UDCCR_SMAC | UDCCR_UDR | UDCCR_UDE)
+#define UDCCSR_WR_MASK (UDCCSR_DME | UDCCSR_FST)
+#define UDC_FNR_MASK (0x7ff)
+#define UDC_BCR_MASK (0x3ff)
+
+/*
+ * UDCCR = UDC Endpoint Configuration Registers
+ * UDCCSR = UDC Control/Status Register for this EP
+ * UDCBCR = UDC Byte Count Remaining (contents of OUT fifo)
+ * UDCDR = UDC Endpoint Data Register (the fifo)
+ */
+#define ofs_UDCCR(ep) (UDCCRn(ep->idx))
+#define ofs_UDCCSR(ep) (UDCCSRn(ep->idx))
+#define ofs_UDCBCR(ep) (UDCBCRn(ep->idx))
+#define ofs_UDCDR(ep) (UDCDRn(ep->idx))
+
+/* Register access macros */
+#define udc_ep_readl(ep, reg) \
+ readl((ep)->dev->regs + ofs_##reg(ep))
+#define udc_ep_writel(ep, reg, value) \
+ writel((value), ep->dev->regs + ofs_##reg(ep))
+#define udc_ep_readb(ep, reg) \
+ readb((ep)->dev->regs + ofs_##reg(ep))
+#define udc_ep_writeb(ep, reg, value) \
+ writeb((value), ep->dev->regs + ofs_##reg(ep))
+#define udc_readl(dev, reg) \
+ readl((dev)->regs + (reg))
+#define udc_writel(udc, reg, value) \
+ writel((value), (udc)->regs + (reg))
+
+#define UDCCSR_MASK (UDCCSR_FST | UDCCSR_DME)
+#define UDCCISR0_EP_MASK (~0)
+#define UDCCISR1_EP_MASK 0xffff
+#define UDCCSR0_CTRL_REQ_MASK (UDCCSR0_OPC | UDCCSR0_SA | UDCCSR0_RNE)
+
+#define EPIDX(ep) (ep->idx)
+#define EPADDR(ep) (ep->addr)
+#define EPXFERTYPE(ep) (ep->type)
+#define EPNAME(ep) (ep->name)
+#define is_ep0(ep) (!ep->idx)
+#define EPXFERTYPE_is_ISO(ep) (EPXFERTYPE(ep) == USB_ENDPOINT_XFER_ISOC)
+
+/*
+ * Endpoint definition helpers
+ */
+#define USB_EP_DEF(addr, bname, dir, type, maxpkt) \
+{ .usb_ep = { .name = bname, .ops = &pxa_ep_ops, .maxpacket = maxpkt, }, \
+ .desc = { .bEndpointAddress = addr | (dir ? USB_DIR_IN : 0), \
+ .bmAttributes = type, \
+ .wMaxPacketSize = maxpkt, }, \
+ .dev = &memory \
+}
+#define USB_EP_BULK(addr, bname, dir) \
+ USB_EP_DEF(addr, bname, dir, USB_ENDPOINT_XFER_BULK, BULK_FIFO_SIZE)
+#define USB_EP_ISO(addr, bname, dir) \
+ USB_EP_DEF(addr, bname, dir, USB_ENDPOINT_XFER_ISOC, ISO_FIFO_SIZE)
+#define USB_EP_INT(addr, bname, dir) \
+ USB_EP_DEF(addr, bname, dir, USB_ENDPOINT_XFER_INT, INT_FIFO_SIZE)
+#define USB_EP_IN_BULK(n) USB_EP_BULK(n, "ep" #n "in-bulk", 1)
+#define USB_EP_OUT_BULK(n) USB_EP_BULK(n, "ep" #n "out-bulk", 0)
+#define USB_EP_IN_ISO(n) USB_EP_ISO(n, "ep" #n "in-iso", 1)
+#define USB_EP_OUT_ISO(n) USB_EP_ISO(n, "ep" #n "out-iso", 0)
+#define USB_EP_IN_INT(n) USB_EP_INT(n, "ep" #n "in-int", 1)
+#define USB_EP_CTRL USB_EP_DEF(0, "ep0", 0, 0, EP0_FIFO_SIZE)
+
+#define PXA_EP_DEF(_idx, _addr, dir, _type, maxpkt, _config, iface, altset) \
+{ \
+ .dev = &memory, \
+ .name = "ep" #_idx, \
+ .idx = _idx, .enabled = 0, \
+ .dir_in = dir, .addr = _addr, \
+ .config = _config, .interface = iface, .alternate = altset, \
+ .type = _type, .fifo_size = maxpkt, \
+}
+#define PXA_EP_BULK(_idx, addr, dir, config, iface, alt) \
+ PXA_EP_DEF(_idx, addr, dir, USB_ENDPOINT_XFER_BULK, BULK_FIFO_SIZE, \
+ config, iface, alt)
+#define PXA_EP_ISO(_idx, addr, dir, config, iface, alt) \
+ PXA_EP_DEF(_idx, addr, dir, USB_ENDPOINT_XFER_ISOC, ISO_FIFO_SIZE, \
+ config, iface, alt)
+#define PXA_EP_INT(_idx, addr, dir, config, iface, alt) \
+ PXA_EP_DEF(_idx, addr, dir, USB_ENDPOINT_XFER_INT, INT_FIFO_SIZE, \
+ config, iface, alt)
+#define PXA_EP_IN_BULK(i, adr, c, f, a) PXA_EP_BULK(i, adr, 1, c, f, a)
+#define PXA_EP_OUT_BULK(i, adr, c, f, a) PXA_EP_BULK(i, adr, 0, c, f, a)
+#define PXA_EP_IN_ISO(i, adr, c, f, a) PXA_EP_ISO(i, adr, 1, c, f, a)
+#define PXA_EP_OUT_ISO(i, adr, c, f, a) PXA_EP_ISO(i, adr, 0, c, f, a)
+#define PXA_EP_IN_INT(i, adr, c, f, a) PXA_EP_INT(i, adr, 1, c, f, a)
+#define PXA_EP_CTRL PXA_EP_DEF(0, 0, 0, 0, EP0_FIFO_SIZE, 0, 0, 0)
+
+struct pxa27x_udc;
+
+struct stats {
+ unsigned long in_ops;
+ unsigned long out_ops;
+ unsigned long in_bytes;
+ unsigned long out_bytes;
+ unsigned long irqs;
+};
+
+/**
+ * struct udc_usb_ep - container of each usb_ep structure
+ * @usb_ep: usb endpoint
+ * @desc: usb descriptor, especially type and address
+ * @dev: udc managing this endpoint
+ * @pxa_ep: matching pxa_ep (cache of find_pxa_ep() call)
+ */
+struct udc_usb_ep {
+ struct usb_ep usb_ep;
+ struct usb_endpoint_descriptor desc;
+ struct pxa_udc *dev;
+ struct pxa_ep *pxa_ep;
+};
+
+struct pxa_ep {
+ struct pxa_udc *dev;
+
+ struct list_head queue;
+ unsigned enabled:1;
+
+ unsigned idx:5;
+ char *name;
+
+ /*
+ * Specific pxa endpoint data, needed for hardware initialization
+ */
+ unsigned dir_in:1;
+ unsigned addr:4;
+ unsigned config:2;
+ unsigned interface:3;
+ unsigned alternate:3;
+ unsigned fifo_size;
+ unsigned type;
+};
+
+struct pxa27x_request {
+ struct usb_request req;
+ struct udc_usb_ep *udc_usb_ep;
+ unsigned in_use:1;
+ struct list_head queue;
+};
+
+enum ep0_state {
+ WAIT_FOR_SETUP,
+ SETUP_STAGE,
+ IN_DATA_STAGE,
+ OUT_DATA_STAGE,
+ IN_STATUS_STAGE,
+ OUT_STATUS_STAGE,
+ STALL,
+ WAIT_ACK_SET_CONF_INTERF
+};
+
+static char *ep0_state_name[] = {
+ "WAIT_FOR_SETUP", "SETUP_STAGE", "IN_DATA_STAGE", "OUT_DATA_STAGE",
+ "IN_STATUS_STAGE", "OUT_STATUS_STAGE", "STALL",
+ "WAIT_ACK_SET_CONF_INTERF"
+};
+#define EP0_STNAME(udc) ep0_state_name[(udc)->ep0state]
+
+#define EP0_FIFO_SIZE 16U
+#define BULK_FIFO_SIZE 64U
+#define ISO_FIFO_SIZE 256U
+#define INT_FIFO_SIZE 16U
+
+struct udc_stats {
+ unsigned long irqs_reset;
+ unsigned long irqs_suspend;
+ unsigned long irqs_resume;
+ unsigned long irqs_reconfig;
+};
+
+#define NR_USB_ENDPOINTS (1 + 5) /* ep0 + ep1in-bulk + .. + ep3in-iso */
+#define NR_PXA_ENDPOINTS (1 + 14) /* ep0 + epA + epB + .. + epX */
+
+struct pxa_udc {
+ void __iomem *regs;
+ int irq;
+ struct clk *clk;
+ struct device_d *dev;
+
+ struct usb_gadget gadget;
+ struct usb_gadget_driver *driver;
+ struct pxa2xx_udc_mach_info *mach;
+
+ enum ep0_state ep0state;
+ struct udc_stats stats;
+
+ struct udc_usb_ep udc_usb_ep[NR_USB_ENDPOINTS];
+ struct pxa_ep pxa_ep[NR_PXA_ENDPOINTS];
+
+ unsigned enabled:1;
+ unsigned pullup_on:1;
+ unsigned pullup_resume:1;
+ unsigned vbus_sensed:1;
+ unsigned config:2;
+ unsigned last_interface:3;
+ unsigned last_alternate:3;
+
+};
+
+static inline struct pxa_udc *to_gadget_udc(struct usb_gadget *gadget)
+{
+ return container_of(gadget, struct pxa_udc, gadget);
+}
+
+/*
+ * Debugging/message support
+ */
+#define ep_dbg(ep, fmt, arg...) \
+ dev_dbg(ep->dev->dev, "%s:%s: " fmt, EPNAME(ep), __func__, ## arg)
+#define ep_vdbg(ep, fmt, arg...) \
+ dev_dbg(ep->dev->dev, "%s:%s: " fmt, EPNAME(ep), __func__, ## arg)
+#define ep_err(ep, fmt, arg...) \
+ dev_err(ep->dev->dev, "%s:%s: " fmt, EPNAME(ep), __func__, ## arg)
+#define ep_info(ep, fmt, arg...) \
+ dev_info(ep->dev->dev, "%s:%s: " fmt, EPNAME(ep), __func__, ## arg)
+#define ep_warn(ep, fmt, arg...) \
+ dev_warn(ep->dev->dev, "%s:%s:" fmt, EPNAME(ep), __func__, ## arg)
+
+#endif /* __LINUX_USB_GADGET_PXA27X_H */
--
1.7.5.4
More information about the barebox
mailing list