Hello,<br><br>I have a problem with b43 driver.<br>Here's some information of my system (debian sid)<br><br># dmesg |grep b43<br>[ 2.046367] b43-pci-bridge 0000:04:05.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17<br>
[ 7.860803] b43-phy0: Broadcom 4318 WLAN found (core revision 9)<br>[ 8.039770] Registered led device: b43-phy0::tx<br>[ 8.039784] Registered led device: b43-phy0::rx<br>[ 8.039797] Registered led device: b43-phy0::assoc<br>
[ 8.039810] Registered led device: b43-phy0::radio<br>[ 10.672291] b43 ssb0:0: firmware: requesting b43/ucode5.fw<br>[ 10.710304] b43 ssb0:0: firmware: requesting b43/pcm5.fw<br>[ 10.713597] b43 ssb0:0: firmware: requesting b43/b0g0initvals5.fw<br>
[ 10.730028] b43 ssb0:0: firmware: requesting b43/b0g0bsinitvals5.fw<br>[ 10.852266] b43-phy0: Loading firmware version 478.104 (2008-07-01 00:50:23)<br><br><br># uname -a<br>Linux debiancasa 2.6.34 #1 SMP PREEMPT Mon May 24 22:41:39 CEST 2010 i686 GNU/Linux<br>
<br><br># lspci -vvn|grep 43 -A7<br>04:05.0 0280: 14e4:4318 (rev 02)<br> Subsystem: 1043:100f<br> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-<br> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-<br>
Latency: 64<br> Interrupt: pin A routed to IRQ 17<br> Region 0: Memory at f79f6000 (32-bit, non-prefetchable) [size=8K]<br> Kernel driver in use: b43-pci-bridge<br><br>04:0a.0 0c00: 104c:8023 (prog-if 10 [OHCI])<br>
Subsystem: 1028:0215<br> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-<br> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-<br>
Latency: 64 (500ns min, 1000ns max), Cache Line Size: 64 bytes<br> Interrupt: pin A routed to IRQ 18<br><br># lsmod |grep b43<br>b43 97693 0 <br>mac80211 110180 1 b43<br>cfg80211 95149 2 b43,mac80211<br>
led_class 1575 1 b43<br><br><br>When I bring up the interface (ifup wlan0) <br><br>[12246.900516] b43-phy0: Loading firmware version 478.104 (2008-07-01 00:50:23)<br>[12246.988328] ADDRCONF(NETDEV_UP): wlan0: link is not ready<br>
[12416.648176] wlan0: authenticate with 00:18:4d:2e:85:4a (try 1)<br>[12416.848040] wlan0: authenticate with 00:18:4d:2e:85:4a (try 2)<br>[12417.048048] wlan0: authenticate with 00:18:4d:2e:85:4a (try 3)<br>[12417.248026] wlan0: authentication with 00:18:4d:2e:85:4a timed out<br>
[12463.932235] wlan0: direct probe to 00:18:4d:2e:85:4a (try 1)<br>[12464.132034] wlan0: direct probe to 00:18:4d:2e:85:4a (try 2)<br>[12464.332034] wlan0: direct probe to 00:18:4d:2e:85:4a (try 3)<br>[12464.532023] wlan0: direct probe to 00:18:4d:2e:85:4a timed out<br>
[12517.684235] wlan0: direct probe to 00:18:4d:2e:85:4a (try 1)<br>[12517.884034] wlan0: direct probe to 00:18:4d:2e:85:4a (try 2)<br>[12518.084530] wlan0: direct probe to 00:18:4d:2e:85:4a (try 3)<br>[12518.284034] wlan0: direct probe to 00:18:4d:2e:85:4a timed out<br>
<br>..and I can't connect to my access point..<br>My /etc/network/interfaces:<br><br>....<br><br># wireless<br>auto wlan0<br>iface wlan0 inet static<br> #wireless-mode managed<br> wpa-driver wext<br> wpa-conf /etc/wpa_supplicant/wpa_supplicant.conf<br>
# static ip settings<br> address 192.168.0.100<br> netmask 255.255.255.0<br> #network 192.168.0.0<br> #broadcast 192.168.0.255<br> gateway 192.168.0.1<br><br>Could someone plese give me a suggest ?<br>
<br>Thanks a lot.<br>Fabrizio<br><br><br>