[PATCH V2 3.18 7/7] b43: N-PHY: support setting custom TX power
Rafał Miłecki
zajec5 at gmail.com
Thu Jul 31 12:59:48 PDT 2014
Signed-off-by: Rafał Miłecki <zajec5 at gmail.com>
---
Notes: I still need to implement helper for B43_MACCTL_PHY_LOCK, but
this may require wider changes, so will be handled in another patch.
V2: Make struct b43_ppr part of struct b43_phy_n
---
drivers/net/wireless/b43/b43.h | 1 +
drivers/net/wireless/b43/phy_n.c | 84 ++++++++++++++++++++++++++++++++++------
drivers/net/wireless/b43/phy_n.h | 4 ++
3 files changed, 77 insertions(+), 12 deletions(-)
diff --git a/drivers/net/wireless/b43/b43.h b/drivers/net/wireless/b43/b43.h
index d55bd86..c0dda0b 100644
--- a/drivers/net/wireless/b43/b43.h
+++ b/drivers/net/wireless/b43/b43.h
@@ -457,6 +457,7 @@ enum {
#define B43_MACCTL_RADIOLOCK 0x00080000 /* Radio lock */
#define B43_MACCTL_BEACPROMISC 0x00100000 /* Beacon Promiscuous */
#define B43_MACCTL_KEEP_BADPLCP 0x00200000 /* Keep frames with bad PLCP */
+#define B43_MACCTL_PHY_LOCK 0x00200000
#define B43_MACCTL_KEEP_CTL 0x00400000 /* Keep control frames */
#define B43_MACCTL_KEEP_BAD 0x00800000 /* Keep bad frames (FCS) */
#define B43_MACCTL_PROMISC 0x01000000 /* Promiscuous mode */
diff --git a/drivers/net/wireless/b43/phy_n.c b/drivers/net/wireless/b43/phy_n.c
index 57a3ab2..cf625d8 100644
--- a/drivers/net/wireless/b43/phy_n.c
+++ b/drivers/net/wireless/b43/phy_n.c
@@ -34,6 +34,7 @@
#include "radio_2056.h"
#include "radio_2057.h"
#include "main.h"
+#include "ppr.h"
struct nphy_txgains {
u16 tx_lpf[2];
@@ -3606,16 +3607,6 @@ static void b43_nphy_iq_cal_gain_params(struct b43_wldev *dev, u16 core,
* Tx and Rx
**************************************************/
-static void b43_nphy_op_adjust_txpower(struct b43_wldev *dev)
-{//TODO
-}
-
-static enum b43_txpwr_result b43_nphy_op_recalc_txpower(struct b43_wldev *dev,
- bool ignore_tssi)
-{//TODO
- return B43_TXPWR_RES_DONE;
-}
-
/* http://bcm-v4.sipsolutions.net/802.11/PHY/N/TxPwrCtrlEnable */
static void b43_nphy_tx_power_ctrl(struct b43_wldev *dev, bool enable)
{
@@ -4069,6 +4060,7 @@ static void b43_nphy_tx_power_ctl_setup(struct b43_wldev *dev)
s16 a1[2], b0[2], b1[2];
u8 idle[2];
+ u8 ppr_max;
s8 target[2];
s32 num, den, pwr;
u32 regval[64];
@@ -4147,7 +4139,12 @@ static void b43_nphy_tx_power_ctl_setup(struct b43_wldev *dev)
b1[0] = b1[1] = -1393;
}
}
- /* target[0] = target[1] = nphy->tx_power_max; */
+
+ ppr_max = b43_ppr_get_max(dev, &nphy->tx_pwr_max_ppr);
+ if (ppr_max) {
+ target[0] = ppr_max;
+ target[1] = ppr_max;
+ }
if (dev->phy.rev >= 3) {
if (sprom->fem.ghz2.tssipos)
@@ -5889,6 +5886,69 @@ static void b43_nphy_set_rx_core_state(struct b43_wldev *dev, u8 mask)
b43_mac_enable(dev);
}
+static enum b43_txpwr_result b43_nphy_op_recalc_txpower(struct b43_wldev *dev,
+ bool ignore_tssi)
+{
+ struct b43_phy *phy = &dev->phy;
+ struct b43_phy_n *nphy = dev->phy.n;
+ struct ieee80211_channel *channel = dev->wl->hw->conf.chandef.chan;
+ struct b43_ppr *ppr = &nphy->tx_pwr_max_ppr;
+ u8 max; /* qdBm */
+ bool tx_pwr_state;
+
+ if (nphy->tx_pwr_last_recalc_freq == channel->center_freq &&
+ nphy->tx_pwr_last_recalc_limit == phy->desired_txpower)
+ return B43_TXPWR_RES_DONE;
+
+ /* Make sure we have a clean PPR */
+ b43_ppr_clear(dev, ppr);
+
+ /* HW limitations */
+ b43_ppr_load_max_from_sprom(dev, ppr, B43_BAND_2G);
+
+ /* Regulatory & user settings */
+ max = INT_TO_Q52(phy->chandef->chan->max_power);
+ if (phy->desired_txpower)
+ max = min_t(u8, max, INT_TO_Q52(phy->desired_txpower));
+ b43_ppr_apply_max(dev, ppr, max);
+ if (b43_debug(dev, B43_DBG_XMITPOWER))
+ b43dbg(dev->wl, "Calculated TX power: " Q52_FMT "\n",
+ Q52_ARG(b43_ppr_get_max(dev, ppr)));
+
+ /* TODO: Enable this once we get gains working */
+#if 0
+ /* Some extra gains */
+ hw_gain = 6; /* N-PHY specific */
+ if (b43_current_band(dev->wl) == IEEE80211_BAND_2GHZ)
+ hw_gain += sprom->antenna_gain.a0;
+ else
+ hw_gain += sprom->antenna_gain.a1;
+ b43_ppr_add(dev, ppr, -hw_gain);
+#endif
+
+ /* Make sure we didn't go too low */
+ b43_ppr_apply_min(dev, ppr, INT_TO_Q52(8));
+
+ /* Apply */
+ tx_pwr_state = nphy->txpwrctrl;
+ b43_mac_suspend(dev);
+ b43_nphy_tx_power_ctl_setup(dev);
+ if (dev->dev->core_rev == 11 || dev->dev->core_rev == 12) {
+ b43_maskset32(dev, B43_MMIO_MACCTL, ~0, B43_MACCTL_PHY_LOCK);
+ b43_read32(dev, B43_MMIO_MACCTL);
+ udelay(1);
+ }
+ b43_nphy_tx_power_ctrl(dev, nphy->txpwrctrl);
+ if (dev->dev->core_rev == 11 || dev->dev->core_rev == 12)
+ b43_maskset32(dev, B43_MMIO_MACCTL, ~B43_MACCTL_PHY_LOCK, 0);
+ b43_mac_enable(dev);
+
+ nphy->tx_pwr_last_recalc_freq = channel->center_freq;
+ nphy->tx_pwr_last_recalc_limit = phy->desired_txpower;
+
+ return B43_TXPWR_RES_DONE;
+}
+
/**************************************************
* N-PHY init
**************************************************/
@@ -6422,6 +6482,7 @@ static int b43_nphy_op_allocate(struct b43_wldev *dev)
nphy = kzalloc(sizeof(*nphy), GFP_KERNEL);
if (!nphy)
return -ENOMEM;
+
dev->phy.n = nphy;
return 0;
@@ -6662,5 +6723,4 @@ const struct b43_phy_operations b43_phyops_n = {
.switch_channel = b43_nphy_op_switch_channel,
.get_default_chan = b43_nphy_op_get_default_chan,
.recalc_txpower = b43_nphy_op_recalc_txpower,
- .adjust_txpower = b43_nphy_op_adjust_txpower,
};
diff --git a/drivers/net/wireless/b43/phy_n.h b/drivers/net/wireless/b43/phy_n.h
index 30bec81..a6da2c3 100644
--- a/drivers/net/wireless/b43/phy_n.h
+++ b/drivers/net/wireless/b43/phy_n.h
@@ -2,6 +2,7 @@
#define B43_NPHY_H_
#include "phy_common.h"
+#include "ppr.h"
/* N-PHY registers. */
@@ -967,6 +968,9 @@ struct b43_phy_n {
struct b43_phy_n_txpwrindex txpwrindex[2];
struct b43_phy_n_pwr_ctl_info pwr_ctl_info[2];
struct b43_chanspec txiqlocal_chanspec;
+ struct b43_ppr tx_pwr_max_ppr;
+ u16 tx_pwr_last_recalc_freq;
+ int tx_pwr_last_recalc_limit;
u8 txrx_chain;
u16 tx_rx_cal_phy_saveregs[11];
--
1.8.4.5
More information about the b43-dev
mailing list