chip id 4318 regression: WARN_ON_ONCE(sdata->vif.hw_queue[i] >= n_queues))

[Andre Heider]

On Fri, Jun 8, 2012 at 6:08 PM, Johannes Berg <johannes at sipsolutions.net> wrote:
> On Fri, 2012-06-08 at 18:05 +0200, Andre Heider wrote:
>> On Fri, Jun 8, 2012 at 5:59 PM, Johannes Berg <johannes at sipsolutions.net> wrote:
>> > On Fri, 2012-06-08 at 17:56 +0200, Andre Heider wrote:
>> >
>> >> > Hopefully this is better: http://p.sipsolutions.net/017d73ac0688f863.txt
>> >>
>> >> The previous patched all had the mac suspend failure. This one:
>> >>
>> >> drivers/net/wireless/b43/main.c: In function 'b43_qos_upload_all':
>> >> drivers/net/wireless/b43/main.c:3483: error: size of array 'type name'
>> >> is negative
>> >> drivers/net/wireless/b43/main.c: In function 'b43_qos_clear':
>> >> drivers/net/wireless/b43/main.c:3502: error: size of array 'type name'
>> >> is negative
>> >> drivers/net/wireless/b43/main.c: In function 'b43_op_conf_tx':
>> >> drivers/net/wireless/b43/main.c:3578: error: size of array 'type name'
>> >> is negative
>> >
>> > Huh, I thought I compiled it ... guess I had the wrong version.
>> >
>> > http://p.sipsolutions.net/511dda98892d2c9a.txt
>>
>> It's getting warmer:
>>
>> [    9.456216] b43-phy0: Loading OpenSource firmware version 410.31754
>> [    9.473798] b43-phy0: Hardware crypto acceleration not supported by firmware
>> [    9.491781] b43-phy0: QoS not supported by firmware
>> [    9.868750] b43-phy0 debug: Chip initialized
>> [    9.888580] b43-phy0 debug: PIO initialized
>> [    9.899273] b43-phy0 debug: QoS disabled
>> [   10.088420] b43-phy0 debug: Wireless interface started
>> [   10.212209] b43-phy0 debug: Adding Interface type 2
>> [   12.739776] wlan0: authenticate with d8:5d:4c:9c:31:14
>> [   12.796248] wlan0: send auth to d8:5d:4c:9c:31:14 (try 1/3)
>> [   12.811768] wlan0: authenticated
>> [   12.823310] wlan0: associate with d8:5d:4c:9c:31:14 (try 1/3)
>> [   12.844942] wlan0: RX AssocResp from d8:5d:4c:9c:31:14 (capab=0x411
>> status=0 aid=2)
>> [   12.863966] wlan0: associated
>> [   16.319097] ieee80211 phy0: wlan0: No probe response from AP
>> d8:5d:4c:9c:31:14 after 500ms, disconnecting.
>> [   16.349674] cfg80211: Calling CRDA for country: DE
>> [   17.597307] wlan0: authenticate with d8:5d:4c:9c:31:14
>> [   17.638399] wlan0: send auth to d8:5d:4c:9c:31:14 (try 1/3)
>> [   17.851085] wlan0: send auth to d8:5d:4c:9c:31:14 (try 2/3)
>> [   18.063086] wlan0: send auth to d8:5d:4c:9c:31:14 (try 3/3)
>> [   18.275081] wlan0: authentication with d8:5d:4c:9c:31:14 timed out
>>
>> Tried it 3 times, always times out.
>
> So you didn't get the warning, but can you still check what
> info->hw_queue is in pio.c?

always "1"