[PATCH 1/2] ssb: add PCI ID 0x4350
spameden
spameden at gmail.com
Sat Dec 29 18:02:58 EST 2012
2012/12/29 Hauke Mehrtens <hauke at hauke-m.de>:
> Please stop top posting
>
> A: Because we read from top to bottom, left to right.
> Q: Why should I start my reply below the quoted text?
>
> A: Because it messes up the order in which people normally read text.
> Q: Why is top-posting such a bad thing?
>
> A: The lost context.
> Q: What makes top-posted replies harder to read than bottom-posted?
>
> A: Yes.
> Q: Should I trim down the quoted part of an email to which I'm replying?
>
> http://www.idallen.com/topposting.html
I'm sorry If I did it wrong.
>
>
> On 12/27/2012 07:26 AM, spameden wrote:
>> Hi guys I have the same device.
>>
>> I'm wondering if it's fully supported or not by b43 driver.
>>
>> Here
>> http://linuxwireless.org/en/users/Drivers/b43?highlight=%2814e4%29#Supported_devices
>> I can see it's listed as supported in N-phy, but as Aitor said on
>> OpenWRT only b/g mode supported for some reason..
>
> n-phy is the name of the phy, the hardware supports ieee80211n, but b43
> does not support ieee80211n at all.
thanks for clarification!
>
>> I can provide all needed info for this device, I have it in my old ASUS
>> WL-500gP v1.
>>
>> On the other note there is a leaked broadcom source of wl driver from
>> Belkin F7D4401 v1.00.39 (it was posted online), I hope it helps:
>
> We already have a spec for this phy and the n specific stuff should also
> be in the phy code b43 uses, someone has just to add support for
> ieee80211n to b43 in general.
ok I'm gonna wait for the retail support I guess..
>
>> http://uploadmirrors.com/download/XLVMMGAJ/Belkin-F7D4401-v1.00.39.tar.7z
>> http://www.mirrorcreator.com/files/1DJEOCRJ/Belkin-F7D4401-v1.00.39.tar.7z_links
>> http://www.digzip.com/files/1L27MJRC/Belkin-F7D4401-v1.00.39.tar.7z
>> http://www.multiupload.nl/P6B0GK9U6R
>>
>> hopefully it'd help.
>>
>> 2012/10/27 Aitor Cuartango <aitor.cuartango at gmail.com
>> <mailto:aitor.cuartango at gmail.com>>
>>
>> If you need more information about the device let me know.
>>
>> With the last openwrt's trunk i can create a wifi network but only
>> in b/g mode.
>>
>> I've test editing manually /etc/config/wireless and change :
>> option hwmode '11g'
>> with
>> option hwmode '11ng'
>>
>> but it does not starts, perhaps i need to do more changes in this
>> file...
>>
>>
>> Thanks all!
>> aitor
>>
>>
>> 2012/10/25 Hauke Mehrtens <hauke at hauke-m.de <mailto:hauke at hauke-m.de>>:
>> > On 10/25/2012 06:47 PM, Rafał Miłecki wrote:
>> >> 2012/10/25 Hauke Mehrtens <hauke at hauke-m.de
>> <mailto:hauke at hauke-m.de>>:
>> >>> 14e4:4350 is found on a Broadcom BCM43222.
>> >>
>> >> Huh, I expected BCM43222 to be BCMA based, interesting. Could you
>> >> provide ssb log for scanning (cores listing) and PHY&RADIO info?
>> >>
>> >
>> > It is not my device, but Aitor found it, here are the details:
>> > http://comments.gmane.org/gmane.comp.embedded.openwrt.user/2031
>> >
>> > Here is the log you requested, without the patches:
>> > ...
>> > b43-pci-bridge 0000:00:02.0: setting latency timer to 64
>> > ssb: Found chip with id 0xA8D6, rev 0x00 and package 0x08
>> > ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x1E, vendor 0x4243)
>> > ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x10, vendor 0x4243)
>> > ssb: Core 2 found: PCI (cc 0x804, rev 0x0E, vendor 0x4243)
>> > ssb: chipcommon status is 0x40040
>> > ssb: Found rev 2 PMU (capabilities 0x044C3002)
>> > ssb: ERROR: PLL init unknown for device A8D6
>> > ssb: ERROR: PMU resource config unknown for device A8D6
>> > ssb: SPROM offset is 0x1000
>> > ssb: SPROM revision 8 detected.
>> > b43-phy0: Broadcom 43222 WLAN found (core revision 16)
>> > ssb: Sonics Silicon Backplane found on PCI device 0000:00:02.0
>> > ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
>> > ...
>> >
>> > Hauke
>
>
More information about the b43-dev
mailing list